Wine & Beverage Cooler Manual We know you don’t want to read through this manual, but trust us, there’s good information in here.
IMPORTANT SAFETY PRECAUTIONS To reduce the risk of fire, electrical shock, or injury when using your appliance, follow these basic precautions: IF YOU READ NOTHING ELSE IN THIS MANUAL, PLEASE READ THIS Risk of child becoming trapped in wine cooler, beverage cooler, other refrigeration unit or large boxes. Junked or abandoned appliances, boxes and other containers are still dangerous, even if they will “just sit in the garage for a few days.
What’s in the box? • • • Instruction manual Handle Spare parts (hopefully you won’t need these) I received my wine or beverage cooler, now what? Your wine or beverage cooler was designed to be built into kitchen or bar cabinets or it will work just fine as a stand alone appliance. Your choice. You should place your wine or beverage cooler on a flat, solid floor that is strong enough to support it when it is fully loaded (300-700 lbs).
Step 3. Using a Philips head screwdriver, push on the screw at the top of the door to make sure it’s protruding through the hole as far as possible and screw in to the appropriate hole on the handle. Do not fully tighten the screw into the handle at this point as it will make attaching the lower portion of the handle difficult. Once the upper screw is screwed into the handle, screw the bottom portion into the handle.
BEV116D – 160 Can Beverage Cooler 5
BEV145SRE – 178 Can Beverage Cooler BEV176D – Dual Zone Wine & Beverage Cooler 6
REVERSE THE DOOR SWING • • • These instructions are based on a wine or beverage cooler assembled with a right hinged door. To reserve the door from right hinge to left hinge, you need to retrieve the Upper Left Hinge, and a Bottom Left Hinge from the spare parts pack shipped with your appliance. Save all extra hinges in case you need to change the direction of the door swing in the future. 1．Open the door, and loosen the screws from the support rod of the bottom hinge.
2．Remove the door from the upper hinge and take out the support rod. 3. Unscrew the upper hinge and bottom hinge. 4. Pry out the plastic caps on the left side of the cabinet, and move them to the right side. 5. Install the hinge set that was included with your instruction manual on the opposite side.
6. Rotate the door 180o so that the top is now the bottom, and install it by attaching the support rod with screws. Quick Start Guide The control panel of your wine or beverage cooler has a saftey feature that prevents someone from accidentally changing the temperature or shutting the appliance off. If left untouched for 10 seconds, the control panel will lock and be unresponsive to touch.
Temperature Range Adjustment Your beverage cooler arrived to you with a factory preset temperature range of 41-72°. While some might think that 41° is a perfectly fine temperature to drink beverages, others might think this temperature is not far off from drinking a cup of piping hot tea. If you want to keep your beverages as icy cold as possible, without freezing, we have provided the following instructions to adjust your wine coolers temperature settings so that the lowest temperature is 36°. Step 1.
Best way to store bottles Your cabinet was designed to store a maximum number of standard sized Bordeaux wine bottles (Wine Cooler) / cans (Beverage Cooler). We recommend that you observe the tips below to optimize loading. • Disperse the bottles / cans evenly to avoid concentrating weight in one place. Bottles / cans must not touch either the back of the cabinet or the step at the bottom. • Make sure that the bottles / cans are not all grouped together either at the top or bottom of the cabinet.
• Be sure the appliance stays secure in the upright position during transportation. If your appliance is moved on an incline greater than 30 degrees, you may upset the balance in your compressor and cause damage. Do not do this. Also protect the outside of the appliance with a blanket or similar item. What to do if something goes wrong? Many common issues with your wine cellar can be solved very easily. Try the troubleshooting tips below should you experience any problems.
The appliance seems to make too much Contraction and expansion of the inside noise. walls may cause popping and crackling noises. The appliance is not on a level surface. The door will not close properly. The appliance is not on a level surface. The door was reversed and not properly installed. The gasket is dirty. The shelves are out of position. The area around the door, top, or side Your appliance comes with a heating element is hot.
with house fuses, circuit breakers, house wiring, and plumbing or gas supply systems resulting from such installation. 5. Damage to or failure of this appliance resulting from improper installation, including installation that was not performed in accordance with electrical, gas or plumbing codes. 6. Damage to or failure of this appliance, including discoloration or surface rust, if it is not correctly operated and maintained according to all supplied instructions. 7.
