COMPRESSION SPRAYER Use and Care Manual CAUTION: Read and follow all instructions Do Not Return This Sprayer To The Store For Help, Information or Parts, Call : 1-800-311-9903 The Fountainhead Group, Inc. 23 Garden St., New York Mills, NY 13417 1-800-311-9903 www.TheFountainheadGroup.com Manual No.
SAFETY PRECAUTIONS TEST SPRAYER WITH WATER BEFORE USING ANY CHEMICALS. • Read owner’s manual completely before operating this sprayer. • Always use goggles, gloves, and protective clothing when using sprayer. • Read and follow all instructions and cautions on label of products used in this sprayer. • Do not leave sprayer in the sun when not in use. • Spray when air is calm to prevent drift of chemicals. • Do not use sprayer near open flame or anything that could cause ignition of the spray.
ASSEMBLY INSTRUCTIONS Assemble Hose To Tank IMPORTANT: Do not attempt to heat or alter hose, hose nut, or barb prior to assembly. 1. Align hose barb tabs, push hose barb into tank until it stops (See Figure A). 2. Slide hose nut into place and turn clockwise to tighten. (See Figure B). NOTE: Do not use tools to tighten hose nut. Assemble Extension, Shut-Off & Nozzle Figure A Figure C Figure B Figure D 1. Install the extension onto the shut-off assembly and tighten the nut securely. (See Figure C) 2.
OPERATING INSTRUCTIONS Filling IMPORTANT: Always make sure the pressure is released from the tank before filling or servicing. If equipped, pull up on the knob of the pressure release valve until all the pressure is released from the tank. Otherwise, squeeze and hold shut-off lever until the unit stops spraying. Then, and only then, it is safe to remove pump. 1. Turn the pump handle counterclockwise to remove the pump (See Figure E). 2. Fill the tank to the desired level. See fill markings on side of tank.
OPERATING INSTRUCTIONS CONTINUED Finish 1. Depressurize the tank as described in Release Tank Pressure section. 2. Turn the pump handle counterclockwise to remove the pump. 3. Empty any remaining liquid according to the product disposal directions. 4. Follow the Cleaning instructions. Cleaning 1. Remove the pump as described in the Finish section. 2. Fill the tank with cool, clean tap water. Replace the pump and tighten securely. 3. Agitate the tank to rinse the chemical from the tank wall and pump. 4.
MAINTENANCE CONTINUED 3. Inspect o-ring. If worn or damaged, remove and replace. Lubricate o-ring with petroleum jelly. (See Figure 4) 4. Inspect check valve in bottom of barrel. If worn or damaged, remove and replace by pressing into hole in bottom of barrel. (See Figure 5) 5. Re-install the barrel into the cap. While holding the cap securely, turn the barrel clockwise to lock the tabs in place. Figure 4 Figure 5 “R” Style 1. Inspect gasket. If worn or damaged, remove and replace. (See Figure 6) 2.
Shut-off Maintenance (Smith Pro II) Always depressurize sprayer before maintenance by activating shut-off and spraying contents out. 1. Unscrew the handle from the shut-off assembly. 2. Remove the filter from the shut-off assembly. 3. Clean any debris from inside the handle, shut-off assembly, or the filter by rinsing with cool, clean water. 4. Reassemble the components as shown and tighten all connections securely. C A B A. Handle B. Filter C.
KITS, PARTS & ACCESSORIES 9G 8-1 8-2 9A 8-3 10G 9B 9E 11B 11A 11D 10C 10E 9D 10A KIT #9 10F 9F 11C 10B KIT #10 9C 10D KIT #11 8-4 11A 11B 11E 7-18 7-14 11C 7-SS 7-21 11E 11F 11G 11F 11D KIT #11-1, 11-2, 11-3 KIT #5 & 5AB 5A KIT #2 2A 5B 2B 5C 11-1 2C 5D 11-2 11-3 2D 5E 2E 5F 2F 5G 2G KIT #5-1, 5-2 4-1 & 4-2 1-1 1-2 1-2 3-2 “O” “R” 3-3 5-3 Page 8
“O” SPRAYER PARTS KEY# 1 PART# DESCRIPTION -2 -3 181036 181120 2 GALLON “O” TANK 3 GALLON “O” TANK “R” SPRAYER PARTS KEY# PART# DESCRIPTION -2 3 -3 -1 182264 182265 182495 2 GALLON “R” TANK (INCLUDES KEY #4) 3 GALLON “R” TANK (INCLUDES KEY #4) VITON PRV ASSEMBLY -2 182500 EPDM PRV ASSEMBLY 4 KIT #2 180398 “O” PUMP 2A 2B 2C 2D 2E 2F 2G 180279 178040 180278 180429 178041 178039V 171015V “O” PUMP HANDLE “O” PUMP CAP “O” PUMP ROD “O” PUMP PISTON ASSEMBLY “O” PUMP BARREL “O” PUMP GASKET, VITON CH
KITS, PARTS & ACCESSORIES KIT #14 KIT #15 15A5 15B 7 4 14A 15C 17 9 14B 15D 14 10 15E 13 12 15F6 14D 15G 3 14C 4 15H KIT #14-1 158 KIT #15-1 15J 16 10 14E 5 15K 11 14F7 15L 9 14G6 15M 10 14H8 15N 15 1 14 15”O” 12 3 14 J 2 15P1 14K 15Q 2 18 13-1A 12-1A 12-1 13 -1 12-1B Page 10
KEY# PART# DESCRIPTION 12-1 12-1A 182490 182678 1 GALLON STAINLESS STEEL TANK PRESSURE RELIEF VALVE FOR 1 GALLON STAINLESS STEEL TANK 12-1B 182677 13-1 182521 13-1A 182679 SHOULDER STRAP FOR 1 OR 3.5 GALLON STAINLESS STEEL TANK 3.5 GALLON STAINLESS STEEL TANK WITH PRESSURE RELIEF VALVE PRESSURE RELIEF VALVE FOR 3.
KITS, PARTS & ACCESSORIES “XL” Shut-Off Off and Wand KIT #23 (18” WAND) KIT #23A (24” WAND) KIT #24 KIT #25 18 16 17 18 B 22C 22B 22F 22A “XB” Shut-Off and Wand KIT #26 27D 27E 22D 27F 22E 21 27C 18 C 27A 27B KIT #27 “ZL” Shut-Off t-Off and Wand KIT #28 (18” WAND) KIT #28A (12” WAND) KIT #29 19 22 KIT #30 22F 20 18 D page 12
KEY# PART# DESCRIPTION KEY# PART# DESCRIPTION 16 182661 22A 176042 17 182565 22B 176171 18 182571 22C 182577 18B 182629 18C 182507 18D 182570 19 182464 20 182639 21 182567 22 182379 24” BRASS WAND ASSEMBLY FOR XL SHUT-OFF 18” BRASS WAND ASSEMBLY FOR XL SHUT-OFF 50” HOSE ASSEMBLY FOR CONCRETE SPRAYER #190448 50” HOSE ASSEMBLY FOR POLY CONCRETE SPRAYER - #190450 50” EPDM HOSE FOR ACETONE SPRAYER - #190451 50” HOSE FOR PEST CONTROL SPRAYER -#190441 18” SS WAND ASSEMBLY FOR ZL SHUT-O
SERVICE KITS, PARTS & ACCESSORIES ARE AVAILABLE BY CONTACTING The Fountainhead Group, Inc. - Customer Service Center Monday - Friday 8 A.M. - 5 P.M., EST Toll Free: 1-800-311-9903 or e-mail: Info@TheFGI.com or Access online at: www.TheFountainheadGroup.
