TABLE OF CONTENTS TITLE PAGE Athletic Field Painting Pointers 1 44-508 Line Star Drawing 2 44-508 Line Star Parts List 3-4 Spray Boom Drawing 5 40-127 Stainless Steel Tank 6 4085 Spray Gun 7 40-153 Gun and Hose Kit 8 44-201 Sulky Drawing 9 44-201 Sulky Parts List 10 Operating Instructions 11-12 Maintenance Instructions 13 Trouble Shooting 13
ATHLETIC FIELD PAINTING POINTERS 1. To achieve the best results and minimize turf damage, use an athletic field marking paint. Choose water-base, not-toxic, non-phytotoxic paint. 2. Mix the paint thoroughly with proper amounts of water to maintain uniform coverage and color throughout the job. Dilution ratios will vary, but two parts water and one part paint usually works best. Read the paint label to be sure you mix it accurately. 3. Prior to painting, mow the turf to provide an even surface.
2
44-508 LINE STAR PARTS LIST REF# PART# DESCRIPTION QTY.
REF.# PART# DESCRIPTION QTY.
REF.# PART# DESCRIPTION QTY. 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 40-139 40-257 400-030 40-258 44-305 400-060 500-243 500-400 19-658 18-003 638 40-128 40-168 49-017 18-007 400-004 500-314 19-697 19-699 19-698 709-053-8004EVS 400-026 44-305-1 400-112 19-680 Frame Boom Mounting Bracket ½” x 5” Bolt with ½” Lock Nut CT Boom Swivel & Lock Double-Tip Boom Box Side with Flaps 5/16” - 18 x 1” Wing Head Thumb Screw ¼” x 4” Gal.
REF.# PART# DESCRIPTION QTY. 1 3 4 6 7 8 9 10 40-127 40-314 40-316 40-317 40-306 40-319 40-302 40-321 40-321-1 40-323 40-323-1 40-324 40-308 40-309 40-310 40-311 40-312 40-303 40-302 40-304 40-313 Tank, 12-gal.
REF# PART# DESCRIPTION QTY. 1 2 *3 4 5 6 *7 8 9 10 11 *12 13 14 15 16 17 18 19 20 21 *22 23 104-158 709-053 104-228 104-226 104-245 104-222 104-244 104-243 104-242 104-206 104-204 104-241 104-240 104-216 104-246 104-247 104-249 104-234 104-238 104-231 104-250 104-251 104-252 Tip Retainer Spray Tip (Specify Size) Seat Stem and Guide Assy.
* Note: Remove #18-064 plug and insert into # 18-063 cross. REF.# PART# DESCRIPTION QTY. 1 2 3 4 5 6 7 8 9 4085 18-066 707-040 18-003 8800-144 19-658 40-048 18-011 19-725 Spray Gun Nozzle Tip (SS-6503) Adapter ¼” NPT Hose Clamp ¼” NPT Hose Clear ¼” 12” Barb Fitting ¼” NPT Shut off Valve ¼” Close Nipple Gasket 1 1 1 2 1 2 1 1 1 Attach spray gun hose to barb fitting using the 18-003 hose clamp. VALVE DIAGRAM FOR OPERATING INSTRUCTIONS WARNING: Never have valve “A” and “B” open at the same time.
9 44-201 SULKY PARTS LIST
REF# PART# DESCRIPTION QTY.
LATEX WATER BASE PAINT 1. Use nozzle Tip 8004EVS. 2. Completely follow mixing instructions on paint container. The solids must be in suspension. 3. To agitate paint in the LINE STAR, see “Agitating Instructions.” 4. Never use mixed paint without straining. 5. The depth of color of the line will be determined by the percentage of water added to the paint. The user must decide for himself the consistency because of the variation in paints that are obtainable.
11. To drain tank, open drain valve on manifold. WARNING: Do not remove cap from the tank unless pressure is released from tank by opening valve “C”. AGITATING INSTRUCTIONS (SEE FIG. VI) If desired to mix the marking liquid in tank, it can be done as follows: 1. Close valve “A”. 2. Open valve “B”. NOTE: To keep paint from going down the CO2 Regulator line, be sure to open valve “A” when agitating is done. If this is not done, paint can be drawn into the CO2 Regulator, causing damage. 3.
Always drain and flush system with water or appropriate solvent after each use. There is only one grease fitting to lubricate: #29-597 Caster Wheel. See engine manual for maintenance instructions. TROUBLE SHOOTING If the line is not satisfactory, the cause could be one of the following reasons: 1. 2. 3. 4. 5. 6. Paint is too thick and mixed properly. If hoses or nozzle clogs, paint was not strained. Nozzle tip is too small or too large. Nozzle tip may be worn. There may be an air leak in system.
