Owners manual

WWW.SMITTYBILT.COM
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Installation Instructions
Street Light Bar
88-98 Chevy Silverado
1500, 2500, 3500
Part #
1
1
00
6
0
Parts Included Qty
3/8” x 1” Hex Bolt 2
3/8” Flat Washer 2
Step 1: Hold the Light Bar up to the face of the bumper where the round mounting brackets are flat against
the bumper. Use the top of the bumper to align the Light Bar perpendicular to the ground.
Step 2: While the Light bar is positioned on the bumper, mark around the two mounting brackets onto the
bumper. Next, remove the light bar and set aside. You should now have two circular marks on the bumper.
Step 3: Mark a ‘X’ through each circle, this will give you the center. Use a metal punch and hammer to
punch a pilot hole through the center of the circle.
Step 4: Drill a ½” hole through the pilot marks. NOTE: Make sure the holes are free of metal burs.
Step 5: Align the Light Bar mounts to the drilled holes and place a 3/8”x 1” bolt and the 3/8” washer through
the back side of the bumper and thread into the light bar bracket. After final positioning, torque each bolt
location to 15-20 ft/lbs. Installation is now complete. NOTE: Removing the bumper may be easier on some
models.
Model 110020 and 110030
Step 1: Drill out the two square license holes using a ½” drill bit. Make sure all holes are free of metal burs.
Step 2: Proceed with Step 5 above. Note: Mount the license plate back behind the Light Bar Bracket.
LIMITED WARRANTY
Smittybilt (The Company) warrants to the original purchaser of this product that should the product or any part thereof, under normal use and conditions, be proven
defective in material or workmanship within 5 years from the original date of purchase, such defect(s) will be repaired or replaced (At the Company’s option) without charge
for parts or labor.
To obtain repair or replacement within the terms of the warranty, the product is to be delivered with proof of warranty coverage ( e.g. dated bill of sale, receipt),
specification of defect, freight pre-paid with Returns Good Authorization Number from Smittybilt to place of purchase. Items returned to Smittybilt without a Returns
Authorization Number will be refused and returned to sender at the sender’s expense. This warranty does not apply to any product or part thereof which, in the opinion of
the Company, has suffered or been damaged through altercation, improper installation, mishandling, misuse, neglect accident or acts of nature. THE EXTENT OF THE
COMPANY’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE
COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID BY THE PURCHASER FOR THIS PRODUCT.
This warranty is in lieu of all expressed warranties and liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY SHALL
BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED
WARRANTY OF MERCHANTABILITY MUST BE BROUGHTH WITHIN A PERIOD OF 90 DAYS FROM DATE OF ORIGINAL PURCHASE.IN NO CASE SHALL THE
COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED,WHATSOEVER. No person or representative is authorized to assume for the company any liability other than expressed herein in connection with the sale of this
product. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage, therefore above
limitations may not apply to you. This warranty gives the purchaser specific legal rights. The purchaser may have additional rights, which vary from state to state.
Please read instructions entirely before installing this product.
Note: Hardware be inserted into Light
Bar for shipping purposes.
Products licensed to N-fab Inc. by Fichter Deisgns are protected by US patent law and International Copy Right law. US Patent #6588783, #
6874801, #7416202. Other patents and continuances pending. N-fab products configuration also protected by International Trade Dress
Law. All Design and Patent infringements will be prosecuted to the full extent of the law.