Installation Manual

ManualsBrandsSmittybilt ManualsAutomotiveSmittybilt 76887 XRC Body Cladding for Jeep JK 4-Door

WWW.SMITTYBILT.COM

For Technical Support/Warranty Information please call 310-762-9944

Smittybilt, 400 West Artesia Blvd, Compton, CA 90220

Installation Instructions

Body Cladding

07-11 JK Unlimited (4-Dr)

Part # 76887

Parts Included P# Qty Parts Included P# Qty

Armor front driver (stock fender) 93-7470 1

Armor front pass (stock fender) 93-7476 1

Armor front driver (XRC fender) 93-7471 1

Armor front pass (XRC fender) 93-7477 1

Armor front door plate 93-7472 2

Armor B pillar pass 93-7478 1

Armor B pillar driver 93-7473 1

Armor rear pass (XRC) 93-7479 1

Armor rear driver (XRC) 93-7474 1

Armor rear pass (stock) 93-7480 1

Armor rear driver (stock) 93-7475 1

Hdwr pack nutcert tool 90-6774 1

Hdwr pack Nutcerts 90-6778 3

Hdwr pack SS button heads 90-6836 1

(

Note) A time saving tool to install rivet nuts or "nutcerts" is RIVET NUT GUN P# 5TUW5. Purchased from Grainger. If

you choose not to purchase the rivet nut gun, a basic tool is supplied.

Step 1: Starting on the driver side, Locate and check fit 93-7473. Make sure this panel fits well and is centered

between the doors with no interference. Mark the hole locations and the corners. Do not drill until all panels have been

marked and check fit. See figure A

Figure A

Please read instructions entirely before installing this product. Drilling is required to install this part.

The 4door JK armor panels fit JK's with or without Smittybilt Armor P# 76880 and 76882.

Summary of content (4 pages)

PAGE 1
Installation Instructions Body Cladding 07-11 JK Unlimited (4-Dr) Part # 76887 WWW.SMITTYBILT.COM Please read instructions entirely before installing this product. Drilling is required to install this part. The 4door JK armor panels fit JK's with or without Smittybilt Armor P# 76880 and 76882.
PAGE 2
WWW.SMITTYBILT.COM Installation Instructions Body Cladding 07-11 JK Unlimited (4-Dr) Part # 76887 Step 2: Moving forward, locate and test fit 93-7472 Mark edges and holes. Inspect that the panels will not overlap. View figure A for lay out Step 3: Moving forward again, locate 93-7470 and 93-7471. If your vehicle has Smittybilt fenders (76880) use 937470. If it has stock fenders use 93-7471. Check fit and mark the appropriate part. Step 4: Locate 93-7474 and 93-7475.
PAGE 3
WWW.SMITTYBILT.COM Installation Instructions Body Cladding 07-11 JK Unlimited (4-Dr) Part # 76887 (TIP) To avoid cross threading the nutcert, make sure to start the bolts by hand. A small amount of grease will help avoid the stainless hardware from sticking or galling to the nutcert. Figure C Step 8: Test fit panels one last time. Use the 3/8 stainless button head hardware from hardware pack (90-6836) There is room to move them around do to the enlarged holes in the panel.
PAGE 4
WWW.SMITTYBILT.COM Installation Instructions Body Cladding 07-11 JK Unlimited (4-Dr) Part # 76887 Limited Warranties Smittybilt’s products are covered under the following limited warranties only. Note that the duration of the limited warranty differs according to the material and finish of the product purchased.