OWNER’S MANUAL Thank you for choosing the Sit N Cycle. We take great pride in producing this quality product and hope it will provide many hours of quality exercise to make you feel better, look better and enjoy life to its fullest. The Sit N Cycle is not a typical exercise bike; it is designed to be a low resistance long duration exercise product. This is great for the office or the home for use during activities where an individual would sit for long periods of time.
ALL NEW MATERIALS Consisting of 100% Polyurethane Date of Manufacture 03/15/13 Model # SNC‐16 Lot # 130310 2
“SAFETY INSTRUCTION” WARNING: To reduce the risk of serious injury, read the following safety instructions before using the item 1. Read all warnings posted on the equipment 2. Read this Owner's Manual and follow it carefully before using the equipment. Make sure that it is properly assembled and tightened before use 3. Keep children and pets away from the equipment. Do not allow children and pets to use or play on the equipment .Always keep children and pets away from the equipment when it is in use 4.
Thank you for choosing the Sit N Cycle. We take great pride in producing this quality product and hope it will provide many hours of quality exercise to make you feel better, look better and enjoy life to its fullest. The Sit N Cycle is not a typical exercise bike; it is designed to be a low resistance long duration exercise product. This is great for the office or the home for use during activities where an individual would sit for long periods of time.
“HARDWARE IDENTIFICATION CHART” Unpack the box in a clear area. Review the Hardware Kit List below. This chart is provided to help identify the hardware used in the assembly process. Place the washers, the end of bolts, or screws on the circles to check for the correct diameter. Use the small ruler to check the length of the bolts and screws.
“ASSEMBLY INSTRUCTIONS” STEP 1 – Seat Cushion & Seat Cover Assembly a. For ease of assembly, turn the Lower Seat Cover Assembly (3) and the Seat Cushion (16) upside down. b. Place the Lower Seat Cover Assembly (3) onto the Seat Cushion (16) and secure with two Bolts (M8xp1.25x30mm)(40) as the drawing depicts on the left. STEP 2 – Seat Assembly a. Remove the Main Frame Assembly (1) along with the die-cut Styrofoam (A) from the carton. b. Lay the unit with the Styrofoam attached on the floor.
ASSEMBLY INSTRUCTIONS” STEP 5 – Pedal Assembly a. Note: The Right Pedal (10) has an R stamped on the end of the pedal shaft. The Left Pedal (9) has an L stamped on the end of the pedal shaft. Assembling the pedals on the wrong side may cause damage to the product. The left and right sides are determined from the back of the seated position on the product, Please see the diagram in step 5. Step a.
“OPERATION INSTRUCTIONS” HOW TO MOVE THE ITEM SAFELY Put your fingers into the handle indentation located on the back of the Seat and gently move the item to the desired location. Make sure the floor is level while moving the item. HOW TO ADJUST THE TENSION LEVEL TO INCREASE THE RESISTANCE : Turn the Tension Knob (24) clockwise. TO DECREASE THE RESISTANCE: Turn the Tension Knob (24) counterclockwise.
“PRODUCT PARTS DRAWING” 9
“PART LIST” NO. Item Name Q'TY NO. Item Name Q'TY SNC-1 Main Frame 1 SNC-29 Lock Washer (M8) 4 SNC-2 Rear Support Frame 1 SNC-30 Washer (8×38×2.0t) 2 SNC-3 Seat Frame 1 SNC-31 Washer (6×13×1.0t) 2 SNC-4 Front Decoration Cover 1 SNC-32 Washer (17×25×1.
LIMITED PARTS WARRANTY 991214(1) LIMITED HOME USE WARRANTY – SMOOTH FITNESS Bikes Warranty Warranty Coverage: Smooth Fitness, Inc. ("Smooth Fitness") warrants to the original owner that each new product will be free from defects in workmanship and material, under normal use and conditions.
Customer Service Toll Free 1-888-800-1167 12
