User Manual

ManualsBrandsSMPL ManualsAssistive TechnologySMPL - Wander Alert Add-On Door Sensor - White

User Guide

1. BOX CONTENTS

2. SIMPLE OVERVIEW

3. SENSORS Door Sensor 1

Motion Sensor 2

4. CONNECT SENSORS TO ALARM

5. SENSOR BATTERY PLACEMENT

6. TROUBLESHOOTING

7. SPECIFICATIONS

8. WARRANTY / TECHNICAL SUPPORT

1. BOX CONTENTS (Select package purchased from the below list)

DOOR SENSOR & ALARM KIT

• 2-piece door sensor (transmitter & magnetic stripe)

• Adhesive tape pre-installed on backside of door sensor and magnet

• 1 portable alarm

• 1 belt clip

• 1 small ‘star’ screwdriver

• 1 button cell battery installed in transmitter (3V CR1632)

• 2 x AAA batteries not included

MOTION SERSOR & ALARM KIT

• 1 motion sensor (with bracket attached)

• Adhesive tape for backside of motion sensor bracket (optional)

• 2 screws and 2 plugs (optional mounting of sensor/bracket)

• 1 portable alarm

• 1 belt clip

• 1 small ‘star’ screwdriver

• 1 button cell battery installed in motion sensor (3V CR2450)

• 2 x AAA batteries not included

Welcome to smpl

ADDITIONAL DOOR SENSOR

• 2-piece door sensor (transmitter & magnetic stripe),

• Adhesive tape pre-installed on backside of Door Sensor and Magnet

• 1 button cell battery installed (3V CR1632)

ADDITIONAL MOTION SENSOR

• 1 motion sensor

• Adhesive tape for backside of motion sensor bracket (optional)

• 2 screws and 2 plugs (optional mounting of sensor/bracket)

• 1 button cell battery installed (3V CR2450)

ADDITIONAL PORTABLE ALARM

• 1 portable alarm

• 1 belt clip

• 1 small ‘star’ screwdriver

• 2 x AAA batteries not included

Summary of content (9 pages)

PAGE 1
TM User Guide 1. BOX CONTENTS 2. SIMPLE OVERVIEW 3. SENSORS Welcome to smpl Door Sensor Motion Sensor 4. CONNECT SENSORS TO ALARM 5. SENSOR BATTERY PLACEMENT 6. TROUBLESHOOTING 7. SPECIFICATIONS 8. WARRANTY / TECHNICAL SUPPORT 1 2 1.
PAGE 2
. OVERVIEW smpl Door or Motion Sensors transmit Radio Frequency (RF) infraction signals to smpl Alarms. (see Fig. 1) • One sensor can signal multiple alarms. • Up to 20 sensors can trigger each alarm. • Designed for Indoor use (not waterproof) Increase monitoring points and alarm locations with additional smpl Sensors and Alarms for increased safety. (see Fig. 2) Fig.
PAGE 3
1. Door Sensor Installation Fig. 3 2 piece Door Sensor Blue indicator Magnet 1.0 x 0.4 inches (25 x 10 mm) Install LESS than 3/4 inch (2cm) apart Sensor 1.75 x 1.2 inches (45 x 30 mm) Test and Install Before ﬁnal installation, please test the alignment on the door (or cabinet) you identiﬁed to monitor. Please follow the simple steps below for headache-free installation. (1) Remove the battery tab from the sensor.
PAGE 4
2. Motion Sensor Installation Familiarize Get alerts when smpl Motion sensors detect movement within 20 ft. Detection range, sensitivity and false alarms are determined by the install location. The motion sensor is comprised of 2 parts, sensor and bracket (pre-installed). See Fig. 7. Fig. 7 SENSOR Blue light indicator BRACKET Install Location Tips • The infrared beam projects straight ahead (detecting heat) and 55° to the right and left (total 110°) as well as downwards at 45° angle. See Fig. 8. Fig.
PAGE 5
4. Once you determined your installation method and location, ﬁrmly attach the sticky pad enclosed on the back of the sensor bracket by pealing one side of the tape. Now peal the other side and lightly press it to the wall location identiﬁed, approximately 6 to 7 feet oﬀ the ground (or as high as you can comfortably reach). Note: The motion sensor can rotate inside the bracket to help point the sensor in the direction of the cross passageway. 5.
PAGE 6
Paring Sensors to Alarms A sensor purchased as part of a kit is already paired with the enclosed alarm and factory default melody is "ding-dong”. If sensor is purchased separately to expand monitored points (or you want to change the melody and/or volume of the paired kit), refer to the below 5 quick steps to pair sensor(s) to alarm(s). Note: You will be required to trigger the sensor quickly when pairing (matching) it to the alarm, so please be located near or beside where the sensor is installed.
PAGE 7
Motion sensor (button cell battery CR2450, 3V) a) Remove mounting bracket from sensor carefully by slowly prying it oﬀ. b) Open bottom grey battery cover by twisting it 1/4 inch counter-clockwise c) Remove the old battery and replace with a new CR2450 button cell battery. Please note that the surface with battery text, i.e. the marking ‘CR2450’ should be facing up. Also, the motion sensor will probably detect your movements and trigger when re-connecting battery.
PAGE 8
Problem: Alarm rings randomly when no one was around to trigger the motion sensor. Reason: There may be random movement of animals, high density frequency interference, heat radiation, or strong air ﬂow in the detection range of sensor. Solution: Identify and eliminate or minimize the source of the false triggers. Problem: Alarm sometimes doesn't ring when someone passes through an expected motion detection area. Reason 1: The movement of passerby may not be detected.
PAGE 9
Motion Sensor Key functions Dimension Battery type Detecting range Wireless range Time interval between 2 detections Low power alert (Yes or No) Waterproof (Yes or No) Rotation angle Operating current Operating voltage Radio transmitting frequency Working temperature Working humidity Beam detects Infrared rays / heat detection Height 1.5 in. X Diameter 1.23 in. (34 mm x 30 mm) 3V CR2450 button battery 20 ft. (4 m) x 170º 250 ft.