Nail Gun User Manual

ManualsBrandsSnap-On ManualsNail Gun870011

MODEL #870011

FOR CUSTOMER SERVICE

PARA EL SERVICIO

PARA EL CONSUMIDOR

1-888-278-8092

Printed in Taiwan

SNAP-ON

IS A TRADEMARK LICENSED BY SNAP-ON

CORP.,

U.S.A., WHICH DOES NOT MANUFACTURE OR

DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE

DIRECTED TO:

1431 VIA PLATA

LONG BEACH, CA 90810-1462 USA

870011 – Clipped Head Air Nailer _Rev 10/4/07

CLIPPED HEAD FRAMING NAILER

INSTRUCTION MANUAL

THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,

MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND

UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO SO

COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.

IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR SNAP-ON

PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE

DEPARTMENT AT 1-888-278-8092. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION

AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION.

Summary of content (15 pages)

PAGE 1
MODEL #870011 CLIPPED HEAD FRAMING NAILER INSTRUCTION MANUAL FOR CUSTOMER SERVICE PARA EL SERVICIO PARA EL CONSUMIDOR 1-888-278-8092 Printed in Taiwan SNAP-ON ® IS A TRADEMARK LICENSED BY SNAP-ON ® CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE DIRECTED TO: ©COPYRIGHT 2007 ALLTRADE TOOLS, LLC.
PAGE 2
TABLE OF CONTENTS CONGRATULATIONS! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . . . 2-3 IMPORTANT INFORMATION ABOUT THIS MANUAL . . . . . . . . . . . 4 SAFETY WARNINGS AND PRECAUTIONS . . . . . . . . . . . . . . . . . . . 4-7 FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage. NOTE provides additional information that is useful for proper use and maintenance of this tool. If a NOTE is indicated make sure it is fully understood. IMPORTANT INFORMATION ABOUT THIS MANUAL Improper maintenance and operation are responsible for the majority of accidents involving clipped head nailers.
PAGE 4
Do not connect clipped head nailer to an air source capable of generating more than 200 psi (14.06 kg/cm2 G). Over-pressurizing the clipped head nailer will result in bursting, abnormal operation or breakage of the tool. Use only clean, dry, regulated compressed air at levels specified on the tool. Failure to comply can cause severe injury or death to the operator or bystanders. Do not attempt to fasten the trigger in the “ON” position. This could lead to an accidental discharge of the clipped head nailer.
PAGE 5
COMPONENT INSTALLATION Thoroughly clean and maintain the clipped head nailer after every use. Lubricate moving parts to prevent rust and minimize friction-related wear. Wipe down the entire tool and remove all dust from the moving parts. Properly store the clipped head nailer in a suitable case to keep it ready for the next job. All maintenance and repairs should be performed by an authorized repair facility.
PAGE 6
To improve the connection between the quick disconnect and air nailer, and to help prevent oxidation, apply PTFE tape or joint compound to the connector threads before insertion. OPERATION IN SINGLE SEQUENTIAL ACTUATION MODE To select the Single Sequential Actuation Mode (see Figure 1): 3. Snap the air hose onto the quick disconnect on the air nailer. Check for air leaks. 1. Press and hold the red Actuation Selector embedded in the trigger.
PAGE 7
To select Contact Sequential Actuation Mode (see Figure 2): Always disconnect the clipped head nailer before making any adjustments to the nail depth setting. 1. Press and hold Actuation Selector embedded in the trigger. 2. Rotate Actuation Selector up to the Contact Sequential Actuation (TTT). 3. Release Actuation Selector, ensuring locking tab is fully seated in the slot. USING THE HOOK Figure 2 Ensure selector has locked into position.
PAGE 8
USING THE NO-MAR NOSEPIECE Always disconnect the air hose before attaching the no-mar nosepiece. In order to prevent the surface of the work piece from being scratched or damaged, use the no-mar nosepiece. Install no-mar nosepiece by pressing it into place on the nose frame. See Figure 5. Store the no-mar nosepiece in place when not being used. 6. Select Single Sequential Actuation Operation. Check for leaks. Without pulling the trigger, press the work piece contact against the work piece.
PAGE 9
CLEARING JAMS DO NOT hold the trigger in a half-pulled position. This could cause an unexpected nailing to occur if the work piece contact is permitted to re-contact the work piece. Failure to comply could result in damage to work piece. LOCKING AND UNLOCKING THE TRIGGER Always move lever to the locked position immediately after using the nailer to prevent unintended firing of fastener.
PAGE 10
Always visually inspect clipped head nailer before every use. Check on the overall condition and for any loose screws. Tighten any screws that have come loose. See Figure 11. MANDATORY MAINTENANCE All maintenance and repairs should be performed by an authorized repair facility. Call 1-888-278-8092 to obtain a list of repair facilities in your area or to make arrangements to return the tool for service. Visually inspect the work piece contact and trigger to ensure there is free movement. See Figure 12.
PAGE 11
PROBLEM POSSIBLE CAUSE SOLUTION Weak drive. Slow to cycle between nailings. Ensure proper air pressure is being used. Inspect for worn driver blade. Inspect piston O-ring for wear or damage. Increase air pressure, Do not exceed 120 psig (8.3 bars, 8.5 kg/cm2) Contact Customer Service. Nails driven too deep. Check air pressure. Reduce air pressure. Clipped head nailer feeds intermittently or skips nails. Ensure correct nails are being used. Inspect nail feeder mechanism.
PAGE 12
PARTS DIAGRAM PARTS LIST ITEM NO. 21 PART NO. DESCRIPTION 1 K0300-4011 Top Cap Set 2 A0000-0421 Nylon Screw M6*18 3 A0005-1071 Washer 4 A0304-0521 Exhaust Cover 5 A0000-0171 Screw M6*30 6 A0005-0541 Washer 12.5*1.6T 7 A0200-0811 O-Ring 11.8*1.5 8 A0203-0111 Muffler 9 K0300-4021 Top Cap & Screw Set 10 A0003-0331 Screw 11 A0301-1641 Cap, Top 12 A0317-0001 Wear Ring 13 A0100-1971 Spring 14 K0300-2741 Firing Valve Set 15 A0200-2612 O-Ring 39.4*3.
PAGE 13
ITEM NO. PART NO. O-Ring 58*2.5 50 A0401-2031 Body A0200-1952 O-Ring 57.5*3.3 51 A0004-0021 Nylon Nut M5 27 A0303-0811 Cylinder 52 K0500-1501 Trigger Set 28 A0800-0781 Spacer 53 A0011-0201 Spring Pin 3*30 29 A0200-2002 O-Ring 85*3.
PAGE 14
ITEM NO. PART NO. DESCRIPTION 75 A0000-0681 BHSC Screw M5*10 76 A0000-0061 Screw M5*12 77 K0700-4741 Magazine Set 78 A0003-0221 Rivet 79 A0718-0561 Magazine Cover 80 A0105-0191 Nail Detainer 81 A0701-2431 Rail Magazine 82 K0700-4771 Pusher Assembly 83 A0102-0071 Spring 84 A0703-0151 Roller, Negator Spring 85 A0005-0311 Pin Retainer 5.
PAGE 15
gations to the purchaser. Alltrade shall not be responsible or liable for any expense, including freight charges, or repairs made outside Alltrade's facility or an Alltrade designated service, unless expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade bear any responsibility for loss of the unit, loss of time or rental, inconvenience, commercial loss, or consequential damages.