41 ZECKOROLL REV ‘A’ OCT 2018
IMPORTANT SAFETY INSTRUCTIONS This document contains important safety and operation instructions for tool storage units. Refer to this information often for safe usage and operation. SAVE THESE INSTRUCTIONS Risk of electric shock and fire.
IMPORTANT SAFETY INSTRUCTIONS CONT This document contains important safety and operation instructions for tool storage units. Refer to this information often for safe usage and operation. SAVE THESE INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS Do not install or store this product where it will be exposed to rain, snow, or wet conditions. To reduce the risk of electric shock and fire, never overload receptacles.
MOVING & STORAGE INSTRUCTIONS Close and lock all drawers, doors, and lids and lock unit prior to moving. Disconnect or unplug all power cords and cable assemblies prior to moving unit. Keep these cables safely stored away from roll cab when moving. When not moving roll cab, be sure to apply all brakes. Be sure to lock front caster wheels parallel to the front of the roll cab prior to opening any drawers. Do not open any drawer with swivel caster facing inward. Units can tip or strike you.
FCC Notice This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
Table of Contents Features.........................................................................................6 Specifications.................................................................................6 Manual Locking / Unlocking...........................................................7 Setting Up ECKO Remote Lock.....................................................8 Remote Use...................................................................................8 Maintenance.......................
Maintenance Setting Up ECKO Remote Lock Each remote lock equipped TSU comes pre-programmed from the factory with the drawers locked. Follow these steps to setup your ECKO remote lock for the first time: Remote Battery Replacement 1. Locate keyway location on remote case. 1. Unlock the TSU using the procedure outlined in the manual unlocking/locking section of this manual. 2. Locate your AC/DC adapter and plug into an electrical outlet that is properly installed and grounded. 3.
Remote Pairing Resetting Remote Lock Receiver Module ECKO remotes come from the factory already paired to the ECKO receiver module. This procedure will only be necessary if your remote has lost pairing. Follow these steps to pair the remote(s) with your TSU: 1. Open top drawer of the TSU and locate the ECKO receiver module. 2. Hold down the learn button on the module until it starts to beep. The unit will beep for 1 second. Release the learn button. 3.
Troubleshooting Symptom Possible Cause Remote battery low Receiver module not receiving power Remote lock does not respond, remote lights up Remote not paired with receiver module Remote out of range Solution - Remove and reinstall remote battery - Replace remote battery - Plug AC/DC adapter into outlet and DC jack on rear of roll cab - Check blue power LED on AC/DC adapter - Check connection between DC cord in tool storage unit (TSU) and receiver module - See Remote pairing section of manual - Move clo
Service – Removing Remote Lock Module Follow these steps to remove the ECKO remote lock receiver module: 1. Remove top two drawers from roll cab. 6. Remove nut and lock washer on back of lock. 2. Remove DC jack from remote lock module. Rear of front dress plate view 3. Disengage snap-fit and remove lock cover. 4. Disengage lock rod from cam mechanism. Lock rod is spring loaded. Push toward back of case and twist clock wise (with respect to front) to disengage. 5. Remove cam assembly screw.
Service – Roll Cab Wiring Service – Roll Cab Part Numbers Follow these steps to replace the ECKO receiver module wiring harness: 8-72737BR Receiver Module with Lock Cover 1. Remove top two drawers from roll cab. 2. Remove DC jack from remote lock module. ECKOFOB Remote 8-72737B-9A Wiring Harness Rear of front dress plate view 8-72737A-AC AC/DC Adapter 3. Remove wiring harness – disconnect from plastic wire hangers and remove from rear of unit.
