| Enclosure QUICK START GUIDE A150 Y.3.B.A.0010-01 V1.0.
Make Something Wonderful Three years ago, when we were designing the Snapmaker Original, we broke the rules of traditional desktop 3D printers and created the first modular 3-in-1 3D printer on the market.
Happy Making Modular System This machine is built for innovators. Our goal is to assist you to make the world a better place with a machine we built with love. The difference could be something as small as a Christmas gift, or something as ambitious as exploring unknown territories of our mankind. Dream big and make it happen. Snapmaker is not only a 3D printer, but also a powerful machine that you can modify with all kinds of addons.
CONTENTS 01 07 36 Before You Start Enclosure Assembly How to Use Before You Start
Before You Start 1.
Before You Start 1.2 Disclaimer Rotate the enclosure parts vertically to a certain degree as shown. Please read and understand the contents of the manual of this product carefully. Failure to read the manual Rotate the enclosure parts horizontally to a certain degree as shown. may lead to personal injury, inferior results or damage to the Snapmaker products. Always make sure that anyone who uses this product knows and understands the contents of the manual to make the most out of it.
Before You Start (2) Detach Touchscreen • Switch off the power and unplug the DC Power Cable. • Disconnect the touchscreen cable from the machine controller and detach the touchscreen. • Detach the touchscreen holder from the machine, and keep it properly.
Enclosure Assembly 01/28 02/28 Assemble the bottom rectangular frame – 1. Assemble the bottom rectangular frame – 2. Each beam of the enclosure frame is engraved with its model name, among which the 24 BEAM A150-1 and 24 BEAM A150-2 vary in length. Make sure to identify the beams by their names and lengths when assembling.
Enclosure Assembly 03/28 Assemble the bottom rectangular frame – 3. 04/28 Attach the Touchscreen Holder.
Enclosure Assembly 05/28 06/28 Attach four 24 Beams. Assemble the top rectangular frame – 1. 90° Notice the position of the LED Strip Port. STEP 04 Do not tighten the screws until Step 9. 24 BEAM A150-3 × 1 Make sure to place the 24 BEAM A1503 in accordance with the direction of the text, with the Hall Switch’s outer covering towards the inside.
Enclosure Assembly 07/28 08/28 Assemble the top rectangular frame – 2. Assemble the top rectangular frame – 3. Notice the position of the LED Strip Port.
Enclosure Assembly 09/28 10/28 Fix the top rectangular frame. Make sure the Enclosure frame is properly assembled by checking the features below. 180° STEP 08 Attach 8 M4 × 28 screws, and tighten all the 16 M4 × 28 screws that are attached in Step 5 and Step 9.
Enclosure Assembly 11/28 12/28 Assemble the Back-Panel Kits. Fix the Back-Panel Kits to the frame. Be sure to put the labeled side of the Exhaust Fan against the Back Panel, with the fan's cable outlet facing up, otherwise the fan will not work properly. 90° STEP 09 M4 × 12 Hex Socket Round Head Screw × 8 1:1 Back Panel × 1 M4 Wing Nut × 4 80×20 Exhaust Fan × 1 Exhaust Duct Connector × 1 Do not tighten the screws excessively lest the acrylic boards should be damaged.
Enclosure Assembly 13/28 Connect the Door Switch Cable to either Door Switch Port of the Enclosure Converter. 14/28 Connect the LED Strips with the Enclosure Converter using two LED Strip Cables.
Enclosure Assembly 15/28 Connect the 80 × 20 Exhaust Fan to the Enclosure Converter. 16/28 Bury the Door Switch Cable and the left LED Strip Cable into the grooves of the beams. Fix the cables with Cable Clips. Tilt the snap joint of the Cable Clip and press it against the groove of the beam to clip it in. The sheet of the Cable Clip should hold the cable inside the adjacent groove.
Enclosure Assembly 17/28 Bury the Exhaust Fan Cable and the right LED Strip Cable into the grooves of the beams. Fix the cables with Cable Clips. 18/28 Transfer the machine to a proper place and enclose the machine with the frame from above. Tilt the snap joint of the Cable Clip and press it against the groove of the beam to clip it in. The sheet of the Cable Clip should hold the cable inside the adjacent groove. Cable Clip × 5 The provided vent duct measures 75mm in diameter and 2m in length.
Enclosure Assembly 19/28 Clamp the Foot Fixtures onto the four feet of the machine, then fix the fixtures onto the enclosure. 20/28 Connect the Enclosure Converter’s Expansion Port with the Addon 3 Port of the machine’s controller using the SMH Expansion Cable. Foot Fixture × 4 M4 × 20 Hex Socket Head Screw × 4 SMH Expansion Cable × 1 1:1 Make sure the connectors are in the right direction.
Enclosure Assembly 21/28 Align the Side Door with the left side face of the frame, then fix the Side Door with screws. 22/28 Connect the Touchscreen to the machine’s Controller and place it on the Touchscreen Holder of the enclosure.
Enclosure Assembly 23/28 Align the Front Door with the front face of the frame, then fix the Front Door with screws. 24/28 Attach the Side Panel.
Enclosure Assembly 25/28 26/28 Attach the Filament Holder. Attach the Top Panel.
Enclosure Assembly 27/28 Put the Handle Hose Clamp around the Exhaust Duct, then enclose the Exhaust Duct Connector with both. Spin the handle clockwise to tighten the clamp. Exhaust Duct × 1 28/28 Connect the Power Module to the machine. Handle Hose Clamp × 1 Make sure the connectors are in the right direction.
3.1 LED Strips & Exhaust Fan Guides & Pictures / Snapmaker How to Use When the machine is not under a 3D printing, laser or CNC process, the LED Strips and the Exhaust Fan can be controlled by entering Home -> Enclosure -> LED Strip or Exhaust Fan on the touchscreen. Before starting a 3D printing, laser or CNC process, it’s recommended to switch ON the LED Strips for a better vision on the work status.
How to Use When the machine is under working condition, you can swipe left on the Touchscreen to control the LED Strips and the Exhaust Fan. 3.2 Change Machine Functions Guides & Pictures / Snapmaker To change the toolheads and the platforms when the machine is enclosed, follow the steps as follow. The H2.5 screwdriver bit will be used. 1. Open the doors. 2. Enter Home -> Controls -> Jog Mode to move the toolhead and platform to proper places that are convenient for detaching. 3.
How to Use To use 3D printing function inside the enclosure, please place the filament as below. 3.3 Door Detection (For Laser & CNC） Guides & Pictures / Snapmaker A built-in smart sensor in the 24 BEAM A150-3 of the enclosure is designed to detect the status of the enclosure doors. When any one of the doors is opened, the laser or CNC process will stop automatically and a notification will be shown on the Touchscreen. To resume the process, close the door and follow the instructions on the Touchscreen.
How to Use Resources This guide is subject to change. For the latest version, go to: https://snapmaker.com/download We are here for you whenever you need general information or technical support: support@snapmaker.com For any sales inquiries, you can reach out to us at: sales@snapmaker.com You can purchase products in our official online store: https://shop.snapmaker.com Share anything you want with other Snapmaker users at our forum: https://forum.snapmaker.
