Quick Start Guide
Manuals
Brands
SNAPMAKER Manuals
3D Printers
3D Printer
54
55
56
57
58
59
60
61
62
63
Table Of Contents
1 Before the start
1.1 Disclaimer
1.2 Expected Use
1.3 Security Information
1.3.1 General Security Information
1.3.2 3D Print security information
1.3.3 Laser safety information
1.3.4 CNC security information
1.3.5 Cover security information
1.3.6 Emergency measures
Burns caused by high-temperature surfaces
Inhaling of smoke and particles
Contact with irritating substances
1.4 Safety Icon
1.5 Specification and parameters
1.6 List of spare parts
1.7 Identifier number
1.8 Assembly and Use Instructions
1.9 About this specification
1.10 Compliance
2 Machine assembly
3 Cover assembly and use
3.1 Outer Cover Assembly
The ① assembled the bottom frame
② assembly support frame
③ mounting side panel and outer cover top
④ assembled the hood doors
⑤ combination cover with machine
The ⑥ installed the backplane and the exhaust sys
⑦ plug in, fix, finish
3.2 Use of the outer cover
3.2.1 Open / close the open and closing detection
3.2.2 Open / close the LED lamp strip and exhaust
4 The 3D printing
4.1 Assemble the 3D printer
4.2 Preparations
4.2.1, Initialize the settings
4.2.2 Calibrate the 3D printing function
1. Load Filament
2. Z-axis offset calibration & hot bed leveling
3. XY axis offset alignment
4.3 Start printing
4.3.1 Install the Snapmaker Luban
4.3.2 Generate the G code
4.3.3 Start the first printing process
4.3.4, Remove the print material
Material outage continuation play & power outage
Replace the module
Firmware update
5 Laser engraving and cutting
5.1 Assemble the laser engraving and cutting machi
5.2 Preparations
5.2.1, Initialize the settings
5.2.2 Calibrate the laser function
1. calibration measurement of material thickness
2. Camera calibration
5.2.3 Fixed materials
5.3 Start the work
5.3.1 Install the Snapmaker Luban
5.3.2 Generate the G code
5.3.3 Start the first operation
Power continued
Replace the module
Firmware update
6 CNC carving and cutting
6.1 Assemble the CNC engraving and cutting machine
6.2 Preparations
6.2.1, Initialize the settings
6.2.2 Fixed materials
6.2.3 Fixed cutting tool
Function introduction: the purpose of the CNC tool
How to fix the CNC tool
6.3 Start the carving
6.3.1 Install the Snapmaker Luban
6.3.2 Generate the G code and send it to the machi
6.3.3 Set the working origin and start the carving
Function introduction: Working origin
How to set up the working origin
6.3.4 Clean up the finished products and machines
Power continued
Firmware update
Replace the module
7 Maintenance and maintenance
7.1 3D Printing
7.1.1 Clean the glass printing board
Remove the consumables residues
Remove solid glue
Remove the grease and dust
7.1.2. Clean the dust proof screen
7.1.3 Clean the spray nozzle
7.2 Laser engraving and cutting
7.2.1 Clean the laser lens shield
7.3 CNC carving and cutting
7.3.1 Fixed nut
5.
Apply
the
mixed
glue
to
the
thread
of
the
nut.
6.
Install
the
nut
into
the
holes
of
the
CNC
carving
and
cut
ting
platform
and
press
for
a
while.
And
wait
f
or
at
least
24
hours
to
ensure
that
the
mixed
glue
is
cured
before
use.
1
...
...
61
62
63
