Safety Instructions & Operator’s Manual for 21” STEEL DECK WALK MOWERS SERIES 12 & 14 MODELS PUSH MODELS 215012 215014 R215012 N215012 NR215012 FR215012 FR215014 PROPELLED MODELS P216012 EP216012 NP216012 RP215012 RP216012 RP215012T2 FRP216012 NRP215012 NFRP216012 MODEL NUMBER EXPLANATION R P MODEL DESIGNATION SELF-PROPELLED CUTTING WIDTH ENGINE HORSE POWER R – Recycling Model F – Flange Type Deck P – Self Propelled Model N – California Model E – European Model 21 – 21” Cutting Width 50 – 5.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine.
IMPORTANT SAFETY INSTRUCTIONS OPERATION MAINTENANCE AND STORAGE 1. 1. DO NOT store mower or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of reach of children in a well ventilated, unoccupied building. 2. Keep mower and engine free of grass, leaves or excess grease to reduce fire hazard and engine overheating. 3.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS.............................................2 & 3 TABLE OF CONTENTS ............................................................................ 4 SECTION 1 - FAMILIARIZATION.............................................................. 5 SECTION 2 - OPERATING INSTRUCTIONS......................................... 6-8 Pre-start Checklist ...............................................................................................
Section 1 - FAMILIARIZATION FIGURE 1.1 1.1 INTRODUCTION This manual has been prepared for the operators of the SNAPPER WALK BEHIND MOWERS. Its purpose, aside from recommending operating and routine service requirements, is to promote safety through the use of accepted operating practices. Read, Understand and Follow the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3 of this manual and all safety messages on the mower and attachments before operating the mower. 1.
Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check guards, deflectors, grass bag, adapter and covers to make sure all are in place and securely tightened. 2.1.2. Check blade control and wheel drive control to insure they work freely. See Figure 2.1. 2.1.6. Clean exterior surfaces of cutting deck and engine of any accumulation of spilled fuel, dirt, grass, oil, etc.
Section 2 - OPERATING INSTRUCTIONS 2.2.2. PROPELLING MOWER (Self Propelled Models Only) 1. Move ground speed control to the desired speed position. See Figure 2.4. 2. Start engine. Refer to Section “Starting & Operation”. 3. Move wheel drive control against handle to engage wheel drive and propel mower forward. Forward speed can be adjusted while the mower is moving by changing position of the ground speed control. See Figure 2.4. 2.
Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. HOLE DESIGNATES TOP OF BAFFLE (ALWAYS KEEP HOLE IN UP POSITION) FRONT DECK BAFFLE FRONT DECK BAFFLE (SHOWN IN HIGHEST POSITION) 2.
Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention model and serial number. 3.2.2. CHECK GREASE LEVEL IN TRANSMISSION 1. Remove transmission fill plug. Roll machine forward or backward while looking down into plug hole. 2.
Section 3 – MAINTENANCE 3.2.4 CHECK ENGINE DRIVE BELT 1. Visually check engine drive belt for cracking, fraying, severed or belt strands exposed. If worn or damaged, replace belt before operating mower. 3.2.2. CHECK GREASE LEVEL IN TRANSMISSION (Continued from previous page) NOTE: Do not spill grease or oil on surface of drive disc. See Figure 3.3. 3. Reinstall transmission plug. 4. Check grease level after each 25 hours of operation. 3.2.5 CHECK TRANSMISSION POLY-V BELT 1.
Section 4 - REPAIR & ADJUSTMENTS 2. Replace the blade if it is badly chipped, bent, noticeably out of balance or has cracks or notch in either tip. See Figure 4.1 & 4.1A. Replace with new blade. WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING CLUTCH CABLE DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. VINYL SPRING 1/16” TO 1/8” CLEARANCE UPPER SPRING CLUTCH CABLE EYE SPRING HOOK LOWER SPRING 4. Sharpen blade on a grinding wheel at an angle of 22 to 28 degrees.
Section 4 - REPAIR & ADJUSTMENTS USE NEEDLE NOSE PLIERS TO INSTALL DRIVE SPRING WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 4.3 DRIVEN DISC SERVICE If the mower does not propel itself properly, See Figure 4.6.
Section 4 - REPAIR & ADJUSTMENTS WARNING 1/8” MEASUREMENT TO OUTSIDE EDGE OF DRIVE DISC DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. DRIVE DISC SLIDE DRIVEN DISC ASSEMBLY TOWARD OUTSIDE EDGE 4.3.3. DRIVEN DISC ADJUSTMENT (Continued From Previous Page) 2.
Section 4 - REPAIR & ADJUSTMENTS 4.3.5. Replacing Bearing In Driven Disc Assembly If the driven disc bearing fails, remove the driven disc assembly and replace bearing as follows: 1. Using a small flat blade screwdriver, free the clip from the transfer rod. Then remove the transfer rod from the clip and the speed control rod. See Figure 4.11. 2. Using needle nose pliers, unhook the drive spring and slide the driven disc assembly off the hex shaft. See Figure 4.12. 3.
Section 4 - REPAIR & ADJUSTMENTS 4.4.1. Engine Drive Belt Replacement 1. Empty the fuel tank. 2. Unhook the idler spring from the right rear wheel bracket. See Figures 4.16. WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. RIGHT REAR WHEEL BRACKET SLOT IN DECK 4.3.6.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. IDLER SPRING RIGHT WHEEL BRACKET 4.4.1. Engine Drive Belt Replacement (Continued from Previous Page) 5.
TROUBLESHOOTING PROBLEM Engine Will Not Start Using Recoil Starter PROBABLE CAUSE 1. Fuel tank empty. 2. Engine needs choking or priming. CORRECTIVE ACTION 1. Fill fuel tank with fresh fuel. 2. Choke/Prime. Check Engine Manual for Instructions. 3. Place spark plug wire onto spark plug. 3. Spark plug wire disconnected. Engine Stalls or Stops 1. Blade control is released or is not being held securely After Running against handle. 2. Choke control in the “CHOKE” position. 3. Fuel tank empty. 4.
SERVICE SCHEDULE ITEM SERVICE PERFORMED Engine Oil REF. EACH USE X 5 HRS 25 HRS Check Oil Level Page 6 Initial Oil Change Page 9 Periodic Oil Change Page 10 X* Clean Sponge Element X** 50 HRS 100 HRS X Air Cleaner Clean or Replace Engine Manual & Page 10. Engine Manual. Spark Plug Replace Engine Manual.
3 YEAR LIMITED WARRANTY For three (3) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
PRIMARY MAINTENANCE 21
PRIMARY MAINTENANCE 22
PRIMARY MAINTENANCE 23
PRIMARY MAINTENANCE 24
NOTES ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ______________________________
NOTES ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ______________________________
NOTES ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ______________________________
Safety Instructions & Operator’s Manual for 21” STEEL DECK WALK BEHIND MOWERS SERIES 12 & 14 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments.