Triple Bag Catcher Kit No. 7600069 - 7600070 Safety Instructions and Operator’s Manual 1 Instruction Manual No. 7102356 (Rev.
IMPORTANT SAFETY INSTRUCTIONS WARNING All safety instructions and operating instructions in the manuals provided with the Snapper Lawn Tractor and this Grass Catcher attachment must be followed. Read, understand, and follow ALL instructions and warnings in the Operator’s Manual provided with the machine, with this attachment, and ALL instructions and warnings on the machine, engine and attachment.
Installation Instructions Install Grass Bag Support 1) Align the lower U-shaped channel on the Grass Bag Support (7500994) with the Ushaped slot in the top of the Bagger Mount. Insert the channel support fully into the bagger mount. See Figure 2. Install Bagger Mount 1) Remove three bolts – two on the rear of the tractor frame, and the top bolt on the right rear of the tractor frame. See Figure 1. The two rear bolts will be replaced with longer bolts supplied in the kit.
Install Grass Bag Adapter 1) 46” & 52” Models Only – Attach the Latch Pin (M720543) to the appropriate Grass Bag Adapter, using one carriage bolt 1/4-20x5/8 (1960252) and one center lock flange nut 1/4-20 (1930642). See Figure 6 (inset). 2) The Grass Bag Adapter attaches to the deck using two bolts and two wing nuts, provided with the kit. See Figure 6. Note – some model tractors will already have the bolts installed in the deck. You can use them to attach the grass bag adapter.
Install Baffles on 52” Deck (Not required on other size decks) 1) Position the left deck baffle (7400267A) and right deck baffle (7400268A) on the front inside surface of the 52” deck. Align the holes and insert carriage bolts (M720053) with the threaded portion sticking out. Install nuts (7090585) onto the carriage bolts. Tighten securely. See Figure 9. Note – some hardware securing the front roller and gauge wheels will have to be removed to install the baffles.
Operation and Maintenance Instructions INTRODUCTION: Follow operation and maintenance instructions in the Operator’s Manual provided with the Snapper Lawn Tractor. EMPTYING GRASS CATCHER 1) Empty Grass Catcher often to avoid overfilling. Overfilling the grass bags reduces performance and causes clogging of tube, adapter and deck. GRASS CATCHER OPERATION 1) Select desired cutting height. Choose a setting that will not attempt to cut off too much at once, overloading the machine.
GRASS CATCHER MAINTENANCE Grass Catcher components are subject to wear and deterioration during normal usage. Inspect all components frequently for signs of wear and deterioration. Replace worn or damaged components immediately. IF THE GRASS CATCHER BECOMES CLOGGED The grass catcher may become plugged if the conditions are too severe, the catcher is overfilled, or the machine is used improperly. If plugging does occur, attempt the following: BEFORE EACH USE 1) Inspect all Catcher components.
Instruction Manual No. 7102356 (Rev.
Parts Manual 9 Instruction Manual No. 7102356 (Rev.
Bagger Mount Tractor Frame Existing Hardware 1 2 Grass Bag Support 3 4 1 2 10 Instruction Manual No. 7102356 (Rev.
BAGGER MOUNT 1 2 ---- 7400272A 1930595 1927557 7091323 7091544 WELDMENT, MOUNT, GRASS CATCHER BOLT – WHIZ LOCK 5/16-18 X 1-1/4 NUT – HEX FLANGE 5/16-18 WHIZ LOCK HEX FLANGE BOLT, 1/2-13 X 1-1/4 HEX FLANGE NUT, 1/2-13 1 2 2 1 1 GRASS BAG SUPPORT 1 2 -3 4 7500994 7091323 7091544 7300957A M720527 ASSEMBLY, GRASS CATCHER SUPPORT HEX FLANGE BOLT, 1/2-13 X 1-1/4 HEX FLANGE NUT, 1/2-13 ARM, SUPPORT, TRIPLE GRASS CATCHER PIN, CHANNEL MTG, GRASS CATCHER 11 1 2 2 1 1 Instruction Manual No. 7102356 (Rev.
Grass Bag Assembly 2 3 1 Cover Assembly 1 3 2 4 12 Instruction Manual No. 7102356 (Rev.
GRASS BAG ASSEMBLY 1 2 -3 ----- 1733695 1733517 1733709 1703807A 1672023A 1931333 1917356 1917372 BAG, GRASS CATCHER, CLOTH HOOP - BAG TRIPLE TUBE, CLIP, GRASS BAG HANGER, GRASS BAG CLAMP, GRASS BAG CARRIAGE BOLT, 5/16-18 X 3/4 LOCKWASHER, SPRING 5/16 NUT - HEX 5/16-18 NC-2B 3 3 3 3 3 6 6 6 COVER ASSEMBLY 1 ----2 3 4 -- 7500996 1733546 M720537 1960404 1933896 M720525 1960074 1733504A 1925003 ASSEMBLY, COVER AND HANDLE, GRASS CATCHER COVER ASSY - TRIPLE HANDLE, COVER SCREW, TRUSS HEAD PHILLIPS, #10-24
Grass Bag Adapter 2 3 4 6 5 1 6 Grass Tube Assembly 1 2 14 Instruction Manual No. 7102356 (Rev.
GRASS BAG ADAPTER 1 1 1 2 3 4 5 -6 M720551 M720560 7102377 M720543 1960252 1930642 1960223 7011791 M720125 42" BAGGER BOOT 46" BAGGER BOOT 52" BAGGER BOOT PIN, LATCH CARRIAGE BOLT, 1/4-20 X 5/8 NUT – CENTER LOCK FLANGE 1/4-20 CARRIAGE BOLT BOLT RETAINER, 5/16- BLACK NUT, 5/16-18 WINGNUT 1 1 1 1 1 1 2 2 2 GRASS TUBE ASSEMBLY – 42” 1 2 -------- 1733885 7500993 1734299 2171600 M720533 M720076 M720074 1928372 1930642 ELBOW - UPPER TUBE ASSEMBLY, TUBE, CENTRAL TUBE, GRASS CATCHER, CLEAR POLY STRAP - RUBBER
Baffle Assembly 4 2 4 1 3 16 Instruction Manual No. 7102356 (Rev.
BAFFLE ASSEMBLY 1 2 3 1 7400268A 7400267A M720053 7090585 BAFFLE, RIGHT BAFFLE, LEFT CARRIAGE BOLT HEX FLANGE NUT, 5/16-18 17 1 1 2 5 Instruction Manual No. 7102356 (Rev.
Instruction Manual No. 7102356 (Rev.
