Parts Manual for TWO-STAGE INTERMEDIATE FRAME SNOW THROWER SERIES 5 & 6 MODEL EI5225 EI75225 EI75246 EI75246E EI8245 EI85245 I5225 I75225 I75246E I8245E I85245E McDonough, GA, 30253 U.S.A. COPYRIGHT © 2006 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED. Manual No.
Table Of Contents PAGE 4 8 10 12 14 16 20 24 30 32 34 GROUP UPPER HANDLES, DASH, CONTROLS CHUTE CRANK CONTROL COLLECTOR HOUSING (3 Piece Bolted) DISCHARGE CHUTE AUGERS, IMPELLER, GEAR CASE, SHAFT TRACTION DRIVE GROUP ENGINE, PULLEYS, IDLER (5 HP Tecumseh) ENGINE, PULLEYS, IDLER (7-1/2, 8, 8-1/2 HP Briggs) WHEELS DECALS ELECTRIC START COMPONENTS TWO-STAGE INTERMEDIATE FRAME SERIES 5 & 6 Manual No.
UPPER HANDLES, DASH, CONTROLS Manual No.
UPPER HANDLES, DASH, CONTROLS Item Part No Qty Description Note or 7091298 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 1919438 1726727 1921332 7027426 1726574 1722638 1726317 1722460 1666255 1916622 1916964 1931317 1720238 1668524 1720240 1715123 1918452 1668185 1924361 1668523 1960705 1921319 1726734 1726983 1726572 7035744 7090391 1960686 1919326 1722633 2 1 4 1 1 1 2 3 1 2 3 2 1 2 1 1 1 2 1 1 1 2 1 1 1 2 2 4 2 1 NUT, 5/16-18 Hex Nyloc BRACKET, Snow Stick- Lower
UPPER HANDLES, DASH, CONTROLS Manual No.
UPPER HANDLES, DASH, CONTROLS Item Part No Qty Description Note 38 39 40 41 42 43 44 45A 45B 46 47 48 49 1726573 1922837 1715654 1960671 1921221 1722631 1920397 7075909 1733209 7091267 1722632 7071895 7027425 1 2 2 2 5 1 2 1 1 1 1 1 1 HANDLE, Upper, Left Hand SCREW, 1/4-20 x 1-1/2” Hex Head Cap SPACER, .268 ID x .394 x .
CHUTE CRANK CONTROL Manual No.
CHUTE CRANK CONTROL Item Part No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1960093 1714084 1667588 7028152 1960074 1720577 1926228 1726939 1918452 1718793 1921319 1960518 1960252 1718593 1960103 1916168 7028159 1960294 7014001 7021828 7011724 7028162 7091070 7091138 7090539 Qty 1 1 3 1 1 1 1 1 1 1 3 2 2 2 1 1 1 2 1 1 1 1 1 1 1 Description Note PUSH NUT, Pal. .375 Dia. Stud Cap KNOB, Spinner BUSHING, .376 x .437 x .20 ROD, Chute, Upper CLIP, .093 Dia.
COLLECTOR HOUSING (3 Piece Bolted) Manual No.
COLLECTOR HOUSING (3 Piece Bolted) Item Part No 1 2 2 3 4 5 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 7072542 7072547 7072567 1930659 7072544 7300099 7200098 1726457 1665982A 108202 7072552 1916965 1931315 7090204 1930641 1960711 1924940 1960687 7091742 7072549 7091315 7091208 7091065 Qty 1 1 1 3 1 1 1 2 1 1 2 4 12 3 12 4 4 4 6 2 3 5 5 Description Note END PLATE, RH- Auger Housing- Red WELDMENT, Auger Housing - 22” - Red WELDMENT, Auger Housing - 24” - Red RETAINER NUT, 5/16-18 END PLATE, LH- Auger
DISCHARGE CHUTE Manual No.
DISCHARGE CHUTE Item Part No Qty Description Note A Chute/Deflector Assy (7075321) includes items 1, 3 & 5.
AUGERS, IMPELLER, GEAR CASE, SHAFT Manual No.
AUGERS, IMPELLER, GEAR CASE, SHAFT Item Part No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 1715091 7090848 7012699 1960474 1715120A 1612093 1666425 936098 1721680 1715580 1670971 1666424 1676027 7091576 1726732 1721676 1676026 1726538 1676024 1726733 7092128 7092125 921133 1726536 1726535 7023590 1668344 1960114 927794 7015894 1612112 7092127 7090052 Qty 1 2 2 1 1 1 1 1 1 1 1 1 2 6 1 1 2 1 1 1 1 6 1 1 1 2 2 4 2 1 1 12 6 Description Note PULLEY, Auger Input
TRACTION DRIVE GROUP Manual No.
TRACTION DRIVE GROUP Item Part No Qty Description Note or 7090361 1 2 3 4 5 1930601 1673994A 7091302 7091320 1669256 3 1 1 1 1 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap BRACKET, Bushing NUT, 3/8-16 Hex, GR 5 or B WASHER, 3/8” Split Lock ASSEMBLY, Shift Arm w/Bushing 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 1666114 7090122 7091305 7091138 1722703 1667341 1917356 7090196 7072432 927794 7091318 1725428 1665995 1678956 1666207 7091829 1667335 7072459 1960353
TRACTION DRIVE GROUP Manual No.
TRACTION DRIVE GROUP Item Part No 38 39 40 41 42 43 44 45 46 47 48 7091214 1719879 1715131 7091598 7091575 1919326 1700473 1666106 7091908 1924366 7091593 Qty 1 1 1 1 1 2 1 1 1 1 1 Description Note KEY, Hi-Pro, #HP-506 DRIVE DISC, w/ Spindle ROD, Pivot COTTER PIN, 1/8 x 3/4” NUT, 5/16-18 Hex Nyloc Light WASHER, .312 (.34 ID x .75 OD) BELLCRANK BUSHING SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 WASHER, Plain, .75 ID x 1.31.OD x .
ENGINE, PULLEYS, IDLER (5 HP Tecumseh) Manual No.
ENGINE, PULLEYS, IDLER (5 HP Tecumseh) Item Part No Qty Description Note or 1921515 1 2 3 7090233 1924874 1715136 4 1 1 SCREW, 5/16-24 x 3/4” Hex Head Cap, GR 5 WASHER, 5/16” Flat WIRE, Belt Stop 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 7090395 3 1 1 3 1 1 2 1 6 2 1 2 4 3 2 4 1 4 1 2 3 1 1 9 1 1 1 1 1 1 1 1 1 1 LOCKWASHER, 5/16” Exterior Tooth * ENGINE, 5HP Tecumseh HOSE, Oil Drain NUT, 5/16-18 Hex Flange Lock- small NUT, 5/16-18 Hex Flange L
ENGINE, PULLEYS, IDLER (5 HP Tecumseh) Manual No.
ENGINE, PULLEYS, IDLER (5 HP Tecumseh) Item Part No Qty Description Note 38 39 925160 7500303 2 1 RIVET, Blind ASSEMBLY, Idler Arm w/Brake Pad 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 7091158 1922755 1668477 1725379 1720237 7092031 924819 1674325 7090201 1720313 7010061 7015861 1930645 7028090 7091075 7034169 7034254 7034251 7034239 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 2 2 2 BOLT, 3/8-16 x 1-3/4 Short Square Neck Carriage, GR 5 WASHER, 3/8” Flat (.41 ID x 1.00 OD x .
ENGINE, PULLEYS, IDLER (7-1/2, 8, 8-1/2 HP Briggs) Manual No.
ENGINE, PULLEYS, IDLER (7-1/2, 8, 8-1/2 HP Briggs) Item Part No 1 2 3A 3B 3C 4 5A 5A 5B 5B 5B 5B 5B 5B 5B 6 7 8 9 10 11 12 13 14 15 16 17 18 19 19 20 21 22 23 24 25 25 1921982 1924874 1725424 7100117 7100118 7090395 1726942 1931277 931277 1715092 7090844 7072556 7028260 1666001 1715559 1929477 1960251 7090122 1674315 1922694 1960687 1715756 7090858 1715111 1919381 7091908 7091908 7027174 Qty 4 1 1 1 1 3 1 1 1 1 1 1 1 1 1 1 3 1 1 2 1 6 2 1 2 4 4 2 4 4 1 4 1 2 3 1 2 Description Note SCREW, 5/16-24 x 1-1
ENGINE, PULLEYS, IDLER (7-1/2, 8, 8-1/2 HP Briggs) Manual No.
ENGINE, PULLEYS, IDLER (7-1/2, 8, 8-1/2 HP Briggs) Item Part No Qty Description Note 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 7072554 7090362 1925125 7091598 1725369 1960268 174870 118414 1717393 1725371 1715118 1669313 925160 7500303 7091158 1922755 1668477 1725379 159106 7092031 924819 1674325 7090201 1720313 7010061 7015861 1724064 1725665 1 9 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 COVER, Bottom- Red SCREW, 1/4-20 x 5/8” Hex Washer Self-Tap W
ENGINE, PULLEYS, IDLER (7-1/2, 8, 8-1/2 HP Briggs) Manual No.
ENGINE, PULLEYS, IDLER (7-1/2, 8, 8-1/2 HP Briggs) Item Part No 64 7090391 Qty 2 Description Note WASHER, 5/16” Internal Tooth Lock Footnotes: NOTE: * See your local Briggs distributor for engine service parts. TWO-STAGE INTERMEDIATE FRAME SERIES 5 & 6 Manual No.
WHEELS Manual No.
WHEELS Item Part No 1 2 3 4 5 6 1666969 172353 1664090 1723286 7027866 7041271 Qty 2 1 1 1 1 2 Description Note KLIK- PIN, .310 ID x 1-3/4” Long VALVE STEM AND CAP TUBE, Tire RIM, 6 x 3.25 (Weldment) TIRE, 15 x 5.00-6, 2 Ply, Carlisle Snow Hog ASSY, Tire and Wheel, 15 x 5.00-6 Carlisle Sno Hog per tire assembly per tire assembly (optional) per tire assembly per tire assembly includes items 2, 4 5 Footnotes: TWO-STAGE INTERMEDIATE FRAME SERIES 5 & 6 Manual No.
DECALS Manual No.
DECALS Item Part No 1 1 2 3A 3B 3C 3D 4 5 6A 6B 7 7 7 7 8A 8B 8C 9 10 11 12 13 13 14 15 Description Note DECAL, Dashboard- RH DECAL, Dashboard- RH- Euro DECAL, Shift Pattern DECAL, Dashboard- LH DECAL, Dashboard- LH- Euro DECAL, Dashboard, Top, LH DECAL, Dashboard, Top, LH (Euro) DECAL, Dash Front - SNAPPER *DECAL, OPEI DECAL - Danger, Auger DECAL, CE- Auger Warning DECAL, Stripe- SNAPPER (5hp, 22”) DECAL, Stripe- SNAPPER (8hp, 24”) DECAL, Stripe- SNAPPER (7.5hp, 22”) DECAL, Stripe- SNAPPER (8.
ELECTRIC START COMPONENTS Manual No.
ELECTRIC START COMPONENTS Item Part No 1 2 3 4 5 6 7600016 7011263 7011264 7011265 7011267 7011268 7011266 Qty 1 1 1 1 1 2 1 Description Note KIT, Electric Start, 230 volt (incl. items 1 thru 6 below) STRAP, Ground (not shown) CLAMP, Regulator (not shown) BRACKET, Regulator (not shown) SCREW, Hex Head BOLT, 5/16-18 x 3/4” Hex Head Cap CLIP, Speed B&S # 226756 B&S # 393514 B&S # 222934 B&S # 95630 B&S # 93343 B&S # 95629 Footnotes: TWO-STAGE INTERMEDIATE FRAME SERIES 5 & 6 Manual No.
Parts Manual for TWO-STAGE INTERMEDIATE FRAME SNOW THROWER SERIES 5 & 6 IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY. McDonough, GA, 30253 U.S.A. COPYRIGHT © 2006 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED. Manual No.
