Safety Instructions & Operator's Manual for L.E. SINGLE STAGE SMALL FRAME SNOW THROWER SERIES 1 MODELS LE3171R LE3191R LE3191E MODEL I MODEL DESIGNATION ENGINE POWER * L I L - Light Weight Frame E - Easy Operation 3 - 3.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following instructions may result in serious injury to the operator or other persons. The owner of the snow thrower must understand these instructions and, furthermore, must allow only persons who understand these instructions to operate snow thrower.
IMPORTANT OPERATIONAL 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. SAFETY PRECAUTIONS Start engine only where exhaust fumes will be safely dissipated. Allow a brief warm-up period, and practice operation of controls outside before putting the machine to work. After striking a foreign object, STOP the engine (motor), remove the key, and remove the wire from spark plug.
IMPORTANT MAINTENANCE 1. 2. 3. 4. 5. SAFETY AND STORAGE INSTRUCTIONS 6. DO NOT store machine or fuel container inside where fumes may reach an open flame, spark, or pilot light as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of reach of children in a well ventilated, unoccupied building. Keep machine and engine free of excess oil, grease and spilled fuel to reduce fire hazard.
TABLE OF CONTENTS SECTION TABLE 1 - IMPORTANT OF CONTENTS SECTION SECTION INSTRUCTIONS .......................... 2-4 ............................................................................. 2 - OPERATING Pre-start Starting Starting Starting SAFETY INSTRUCTIONS 5 ....................................... 6-10 Checklist ........................................................................................... 6-7 & Stopping Engine (Recoil Start Models) ....................................
Section 2 -OPERATING 2.1 INSTRUCTIONS PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check guards, chutes, deflectors and covers to make sure all are in place and securely tightened. 2.1.2. Check auger control to insure it works freely. See Figure 2.1. AUGER CONTROL STANDARD FLUID MEASUREMENT (50:1 Ratio) GASOLINE (Gallons) 0.25 0.50 0.75 1.00 1.25 1.50 2.00 2 CYCLE OIL (Ounces) .64 1.3 1.9 2.6 3.2 3.8 5.
Section 2 -OPERATING 2.1 INSTRUCTIONS PRE-START CHECK LIST (Continued from Previous Page) Make the following checks and perform the service required before each start-up. WARNING DO NOT use an electrical extension cord that is damaged. A damaged electrical extension cord could cause a shock or fire. Thoroughly inspect electrical extension cord before using machine. If cord is damaged, do not use and do not operate machine. Replace damaged cord immediately.
Section 2 -OPERATING 2.2 INSTRUCTIONS STARTING, STOPPING & OPERATION (RECOIL START MODELS) 2.2.1. ENGINE & AUGER 1. Move choke control to the choke "ON" position. See Figure 2.5. NOTE: Stop the auger by releasing the auger control. Stop the engine by turning the key switch to the "OFF" position. (SHOWN IN "OFF POSITION) TURN KEY TO THE "ON" PUSH PRIMER THREE TIMES WARNING Release auger clutch control and make sure auger/impeller has STOPPED before rotating discharge chute or adjusting deflector.
Section 2 -OPERATING INSTRUCTIONS 2.2.4. STOPPING Stop the auger by releasing the auger control. Stop the engine by turning the key switch to the "OFF" position. Always remove key from key switch before leaving machine unattended. See Figure 2.8. RELEASE AUGER CONTROL TO 1. Connect the power cord to the starter switch box on machine's control panel then plug the other end into 120 volt AC receptacle. 2. Turn ignition key to the "ON" position. 3. Move choke control to the choke "ON" position.
Section 2 -OPERATING INSTRUCTIONS DANGER Objects can be thrown by the snow thrower while it is in operation. Thrown objects could cause serious injury to the operator or bystanders. Always wear safety goggles or other suitable eye protection. Keep people and pets away from area. 2.2.6. ENGAGING AUGER 1. Pull auger control against auger. See Figure 2.6. DO NOT clean out discharge chute with hands. Contact with moving parts inside chute will cause serious injury. Use clean out tool provided with machine.
Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the snow thrower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular snow thrower, always mention model and serial number. 3.2 SERVICE - AFTER FIRST 5 HOURS 3.2.3 CHECK AUGER CLUTCH CONTROL CABLE 1. Visually check cable for fraying, kinking or severed cable strands. Replace cable and adjust tension before operating snow thrower.
Section 4 - REPAIR & ADJUSTMENTS 4.1.2. AUGER BELT IDLER PULLEY ADJUSTMENT NOTE: To adjust the idler pulley and properly tension the auger belt, the auger control cable adjustment must first be loosened as described in the following step. Cable adjustment must be checked after completing the idler pulley adjustment. WARNING DO NOT attempt any adjustments, maintenance, service, or repairs with engine running. Stop auger. Stop engine. Remove key. Remove spark plug wire and secure wire away from spark plug.
Section 4 - REPAIR & ADJUSTMENTS 4. Push the spring tensioned idler pulley down and install new belt. See Figure 4.5. WARNING DO NOT attempt any adjustments, maintenance, service,or repairswith engine running.Stop auger. Stop engine. Remove key. Remove spark plug wire and secure wire away from spark plug. BELT COVER RETAINING STUDS SHOWN REMOVED 4.1.2. AUGER BELT IDLER PULLEY ADJUSTMENT (Continued From Previous Page) 3. Loosen nut and bolt that secures the idler pulley to idler arm.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any adjustments, maintenance, service, or repairs with engine running. Stop auger. Stop engine. Remove key. Remove spark plug wire and secure wire away from spark plug. FLITE SHOE 4.1.3. AUGER BELT REPLACEMENT (Continued From Previous Page) 5. Reinstall belt guide. IMPORTANT: Make sure when reinstalling belt guide that it does not touch drive pulley. Belt guide should an equal amount of clearance on both belt guide fingers. See Figure 4.6. 6.
TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Engine Will Not Start 1. Fuel tank empty. 1. Fill fuel tank with flesh fuel/oil mix. Using Recoil Starter 2. Engine needs choking & priming. 1. Power extension cord not plugged into machine or 110 Volt outlet. 2. Move choke control to "CHOKE" position. Push primer bulb three times. 3. Replace spark plug. Attach plug wire onto spark plu_t. 1. Plug power extension cord into machine & into 110 Volt outlet. 2. Power extension cord damaged. 3.
2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
SNAPPER PRODUCT IMPORTANT: KEEP THIS INFORMATION (Complete Model REGISTRATION the following FORM FOR YOUR PERSONAL information RECORDS on your Snapper purchase) purchase Snapper Number Serial Number Date of Purchase Retailer Retailer's Phone It is very warranty Snapper Number important coverage. Please you register You can contact registration Georgia with to ensure card to: 30253. on line at www.sna_er.com. us at our web Representative.
NOTES 18
NOTES 19
Safety Instructions & Operator's Manual for L.E. SINGLE STAGE SMALL FRAME SNOW THROWER SERIES 1 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments.
Safety Instructions & Operator's Manual for L.E. SINGLE STAGE SMALL FRAME SNOW THROWER SERIES 1 MODELS LE3171R LE3191R LE3191E MODEL I MODEL DESIGNATION ENGINE POWER * L I L - Light Weight Frame E - Easy Operation 3 - 3.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following instructions may result in serious injury to the operator or other persons. The owner of the snow thrower must understand these instructions and, furthermore, must allow only persons who understand these instructions to operate snow thrower.
IMPORTANT OPERATIONAL 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. SAFETY PRECAUTIONS Start engine only where exhaust fumes will be safely dissipated. Allow a brief warm-up period, and practice operation of controls outside before putting the machine to work. After striking a foreign object, STOP the engine (motor), remove the key, and remove the wire from spark plug.
IMPORTANT MAINTENANCE 1. 2. 3. 4. 5. SAFETY AND STORAGE INSTRUCTIONS 6. DO NOT store machine or fuel container inside where fumes may reach an open flame, spark, or pilot light as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of reach of children in a well ventilated, unoccupied building. Keep machine and engine free of excess oil, grease and spilled fuel to reduce fire hazard.
TABLE OF CONTENTS SECTION TABLE 1 - IMPORTANT OF CONTENTS SECTION SECTION INSTRUCTIONS .......................... 2-4 ............................................................................. 2 - OPERATING Pre-start Starting Starting Starting SAFETY INSTRUCTIONS 5 ....................................... 6-10 Checklist ........................................................................................... 6-7 & Stopping Engine (Recoil Start Models) ....................................
Section 2 -OPERATING 2.1 INSTRUCTIONS PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check guards, chutes, deflectors and covers to make sure all are in place and securely tightened. 2.1.2. Check auger control to insure it works freely. See Figure 2.1. AUGER CONTROL STANDARD FLUID MEASUREMENT (50:1 Ratio) GASOLINE (Gallons) 0.25 0.50 0.75 1.00 1.25 1.50 2.00 2 CYCLE OIL (Ounces) .64 1.3 1.9 2.6 3.2 3.8 5.
Section 2 -OPERATING 2.1 INSTRUCTIONS PRE-START CHECK LIST (Continued from Previous Page) Make the following checks and perform the service required before each start-up. WARNING DO NOT use an electrical extension cord that is damaged. A damaged electrical extension cord could cause a shock or fire. Thoroughly inspect electrical extension cord before using machine. If cord is damaged, do not use and do not operate machine. Replace damaged cord immediately.
Section 2 -OPERATING 2.2 INSTRUCTIONS STARTING, STOPPING & OPERATION (RECOIL START MODELS) 2.2.1. ENGINE & AUGER 1. Move choke control to the choke "ON" position. See Figure 2.5. NOTE: Stop the auger by releasing the auger control. Stop the engine by turning the key switch to the "OFF" position. (SHOWN IN "OFF POSITION) TURN KEY TO THE "ON" PUSH PRIMER THREE TIMES WARNING Release auger clutch control and make sure auger/impeller has STOPPED before rotating discharge chute or adjusting deflector.
Section 2 -OPERATING INSTRUCTIONS 2.2.4. STOPPING Stop the auger by releasing the auger control. Stop the engine by turning the key switch to the "OFF" position. Always remove key from key switch before leaving machine unattended. See Figure 2.8. RELEASE AUGER CONTROL TO 1. Connect the power cord to the starter switch box on machine's control panel then plug the other end into 120 volt AC receptacle. 2. Turn ignition key to the "ON" position. 3. Move choke control to the choke "ON" position.
Section 2 -OPERATING INSTRUCTIONS DANGER Objects can be thrown by the snow thrower while it is in operation. Thrown objects could cause serious injury to the operator or bystanders. Always wear safety goggles or other suitable eye protection. Keep people and pets away from area. 2.2.6. ENGAGING AUGER 1. Pull auger control against auger. See Figure 2.6. DO NOT clean out discharge chute with hands. Contact with moving parts inside chute will cause serious injury. Use clean out tool provided with machine.
Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the snow thrower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular snow thrower, always mention model and serial number. 3.2 SERVICE - AFTER FIRST 5 HOURS 3.2.3 CHECK AUGER CLUTCH CONTROL CABLE 1. Visually check cable for fraying, kinking or severed cable strands. Replace cable and adjust tension before operating snow thrower.
Section 4 - REPAIR & ADJUSTMENTS 4.1.2. AUGER BELT IDLER PULLEY ADJUSTMENT NOTE: To adjust the idler pulley and properly tension the auger belt, the auger control cable adjustment must first be loosened as described in the following step. Cable adjustment must be checked after completing the idler pulley adjustment. WARNING DO NOT attempt any adjustments, maintenance, service, or repairs with engine running. Stop auger. Stop engine. Remove key. Remove spark plug wire and secure wire away from spark plug.
Section 4 - REPAIR & ADJUSTMENTS 4. Push the spring tensioned idler pulley down and install new belt. See Figure 4.5. WARNING DO NOT attempt any adjustments, maintenance, service,or repairswith engine running.Stop auger. Stop engine. Remove key. Remove spark plug wire and secure wire away from spark plug. BELT COVER RETAINING STUDS SHOWN REMOVED 4.1.2. AUGER BELT IDLER PULLEY ADJUSTMENT (Continued From Previous Page) 3. Loosen nut and bolt that secures the idler pulley to idler arm.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any adjustments, maintenance, service, or repairs with engine running. Stop auger. Stop engine. Remove key. Remove spark plug wire and secure wire away from spark plug. FLITE SHOE 4.1.3. AUGER BELT REPLACEMENT (Continued From Previous Page) 5. Reinstall belt guide. IMPORTANT: Make sure when reinstalling belt guide that it does not touch drive pulley. Belt guide should an equal amount of clearance on both belt guide fingers. See Figure 4.6. 6.
TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Engine Will Not Start 1. Fuel tank empty. 1. Fill fuel tank with flesh fuel/oil mix. Using Recoil Starter 2. Engine needs choking & priming. 1. Power extension cord not plugged into machine or 110 Volt outlet. 2. Move choke control to "CHOKE" position. Push primer bulb three times. 3. Replace spark plug. Attach plug wire onto spark plu_t. 1. Plug power extension cord into machine & into 110 Volt outlet. 2. Power extension cord damaged. 3.
2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
SNAPPER PRODUCT IMPORTANT: KEEP THIS INFORMATION (Complete Model REGISTRATION the following FORM FOR YOUR PERSONAL information RECORDS on your Snapper purchase) purchase Snapper Number Serial Number Date of Purchase Retailer Retailer's Phone It is very warranty Snapper Number important coverage. Please you register You can contact registration Georgia with to ensure card to: 30253. on line at www.sna_er.com. us at our web Representative.
NOTES 18
NOTES 19
Safety Instructions & Operator's Manual for L.E. SINGLE STAGE SMALL FRAME SNOW THROWER SERIES 1 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments.
