:.’ OPERATOR’S MANUAL WIDE BODY CART COLLECTOR Dual Wheel Cart For Use With Turbo Collection System SUNSTAR/ SERIES CART SOVEREIGN/900 SERIES CART MFG. NO. 1691526 Form I 708219 printed in USA l/94-1GCCI LANDLORD/1700 SERIES CART MFG. NO.
,.~.~~ ,.. :L..~ ~~: ‘in. . : :: .:.. ~,: ‘:, .,.: : :. :.,.
Table of Contents Page Standard Fastener Identification Chart.. ..................................................... inside Front Cover Decals ....................................................................................................................................... 1 Specifications ........................................................................................................................... 1 Decals ..................................................................................
6. Hitch and Tube Assembly - SunStar Qw. km 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Series Tube Assy. (Incl. Ref. No. 38) Nut, Hex Full, Lock, #lo-32 Washer, Plain, #l 0 Screw. Phillips, Truss Head, #10-32x l/2 Hose Clamp, 6” Decal, Cleaning Inst. Capscrew, Hex Hd., 7/16-14X l-1/2 Lo&washer, 7/16 Nut, Hex, Full, 7/16 Nut, Hex, Full, l/2-13 Lo&washer, l/2 Bracket, Hitch (Frame) Nut. Hex. Full. 5/S Lockwasher, s/a Bracket, Hitch (Cart) Capscrew, Hex Hd.
Cart Assembly 3. Turn box upside down and install the frame to the Ubracket (figure 4). Align the two prong end (A) in the frame with the ends of the U-bracket and secure with two 112-13 x l-114 hex bolts and locknuts. DO NOT overtighten the locknuts, since the box pivots at this point for dumping. NOTE: Sort out the hardware and arrange by size and type. Refer to figure 1. 1. Install the wheel assemblies (A, figure 2) to the frame (B). Place the head of the swivel wheel on the end of the frame.
. Install the sleeve clamp (C, figure 11) to the connecting sleeve (A) with l/4-20 x l/Z slotted truss head screw (D) and nyloc nut (E). Install the connecting sleeve inside the collar of the cover and position sleeve clamp (C) over the support tube (B). ‘23!i4 Figure 13 A. Straight Rod Figure 11 A. Connecting Sleeve B. Support Tube C. Sleeve Clamp B. Cord Loop C. Bolt D. Truss Head Screw, l/4-20 x 112 E. Nyloc Nut 7.
Discharge Tube Installation Landlord/1700 Series (Mfg. No. 1692095) 1. Install the spring clip (D, figure 18) with two 10-32 x i/2 truss head screws (E), four flat washers (F), and two locknuts (G). 2. Install l/4-20 x 5/8 carriage bolt (H) through hole in turbo housing. Secure with l/4-20 flange locknut (I). 3. Position the lower tube (C) onto turbo housing and hook inside spring clip onto flange locknut (I, installed in step 2). Mark hole location on opposite side of turbo housing for outer spring clip.
Operation Maintenance Grass should be cut often, and not too short. If grass is too long or lush it may be necessary to keep ground speed to a minimum or to cut only half the width to prevent clogging. If grass is high, operate with mower in high cutting position. Cut the grass again in lower cutting position, if desired. The cart cover IS subject to wear and detenoration. Check the cover frequently. Use an * The collector is full when grass builds at the window.
TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE TOLERANCE +20% SIZE SAE GRADE #2 SAE GRADE #5 SAE GRADE #S Q 8 0 In./Lbs. 8-32 8-36 1 O-24 1 O-32 I/4-20 l/4-28 5/i 6-l 8 5/l 6-24 318-l 6 318-24 7116-14 7/l 6-20 l/2-13 I/2-20 9116-l 2 9/l 6-18 518-l 1 518-l 8 314-l 0 314-l 6 718-9 718-l 4 1-8 l-12 InJLbs. In./Lbs. FtJLbs. N m . Ft./Lbs. 19 20 27 31 66 76 11 12 20 23 30 35 50 55 65 75 90, 100 160 180 140 155 220 240 2.1 2.3 3.1 3.5 7.6 8.6 15. 16.3 27.2 31.3 40.8 47.6 68. 74.8 88.4 102. 122.
