AVN S7000 In-dash Motorised 7” Wide Touchscreen Satellite Navigation, AM/FM Receiver, DVD Player User Manual
SAFETY INFORMATIONS TABLE OF CONTENTS Safety Informations Features Accessories Unit Installation Installation Removal Wiring Connection and Diagram Disc Notes Installing the N7000 Navibox Unit View Front Panel Front Panel Display Remote Control Basic Operation Touch Screen Operations Touch Screen Calibrate Main Menu Radio Operations DVD Operations USB Operations TV Operations iPod Operations AV IN Operations Bluetooth Operations System Setup DVD Setup Menu
• Do not use any chemical solvent, cleaning agent or corrosive detergent to clean away dirt on the surface of the TFT monitor screen. It may cause irreversible damage. • Small black and shiny dots inside the liquid crystal panel are normal for liquid crystal product. • In extremely cold temperatures, the movement of the picture may be slow and the picture may be dark, but this is not a malfunction. The unit will work normally once reach its operating temperature.
ACCESSORIES UNIT INSTALLATION INSTALLATION Please read all of the instructions before beginning the installation. It is strongly recommended to have your unit installed by a professional installation shop.
Securing the Unit to the Mounting Bracket REMOVAL 1. Detach the front panel. Installation Method 1. Install the front panel into the unit. 2. Bend the claws outward for tight fit, if necessary. Install the Mounting Box into the dashboard, tighten the unit in place. 2. Insert the keys that supply to the unit at both sides of the unit (shown as illustrated) until pull the keys to make it possible to remove the unit from the dashboard. 3. Install the Frame to the unit.
WIRING CONNECTION FUSE REPLACEMENT – WARNING! Cautions: • To prevent short circuits, remove the key from the ignition and disconnect the terminal of the battery. • Make the proper input and output cable connections for each unit. • Connect the wiring harness cables in the following order: ground wire, battery wire, ignition wire. • Reconnect the terminal of the battery. • Do not connect the yellow wire of this product directly to the battery terminal.
Notes: • If the TV antenna is mounted near a radio antenna, reception quality may be affected during simultaneous reception of TV and Radio broadcasts. • Please separate Battery Units before setting products to prevent from fire and electric shock. Mounting the antenna near to a radio antenna will result in noise. In this case, consult your dealer concerning mounting location.
INSTALLING THE N7000 NAVI BOX Mounting the Navi box Components The Navi box needs to be mounted in a position where you have access to the SD card. This is critical if you wish to perform speed camera updates or map updates. There are a number of suitable places to mount the Navi box depending on your vehicle including the glove box, under the driver’s or passengers seat or in the boot. It may also be possible to mount under the dash board in some cases.
UNIT VIEW FRONT PANEL 1. [ANGLE -] / 2. [ANGLE +] Adjust the view angle of the monitor to choose the best displaying effect. 1- Continual angle adjustment Hold on pressing the [ANGLE +] / [ANGLE -] buttons to adjust the angle of TFT monitor upward / downward by continual increasing / decreasing. 2- Single step angle adjustment Press the [ANGLE +] / [ANGLE -] buttons to adjust the angle of TFT monitor upward / downward by singly increasing / decreasing. 3.
13. [F.FWD] Press to select fast forward with different speed. FRONT PANEL DISPLAY 14. [F.REV] Press to select fast reverse with different speed. 15. [PREVIOUS] Press to skip to play the pervious track. 16. [NEXT] Press to skip to play the next track. 17. [AUX IN] Connect an external audio device to this jack to listen the sound through your car speakers (jack cable is not supplied). 18. [REMOTE] Infrared Remote Receiver. 19.
9. LD Icon: (Loudness) It displays when the LOUD function is on. REMOTE CONTROL 10. ST Icon: (Stereo) It displays if listened station has stereo broadcast. 11. Disc Type Indicator: It indicates the type of disc played (DVD, CD, VCD and MP3). 1. POWER/SOURCE 2. MUTE 3. NUMBER BUTTONS 4. MENU / * 5. AUDIO / # 6. LOUD / EQ 7. UP (Tune up)/PTY 8. LEFT (Seek Down) 9. ENTER / BAND 10. PROGRAM 11. DOWN (Tune Down)/AF 12. RANDOM / TRANSFER 20 13. PREVIOUS 14. SLOW / END CALL 15. TITLE / PBN 16. ZOOM / CALL 17.
1. [POWER/SOURCE] Same functions as key on front panel. 2. [MUTE] Press the [MUTE] button to switch off the sound; press it again to resume to the previous volume level. 3. [NUMBERS 0~9] For 1~6, press these buttons to store the current radio station or recall the stored station under the Radio Mode. For 0~9, press these buttons to select the tracks, and input the number code. 13. [PREVIOUS] Press to skip to play the pervious track. 14. [SLOW/END CALL] Press to activate slow motion playback.
26. [F.FWD] Press to select fast forward with different speed. 28. [STOP] Press to stop the playback. 29. [ANGLE] Press the [ANGLE] button during playback to select different viewing angles with interactive DVD media. 30. [PLAY/PAUSE] Press to pause the playback when playing; press again to continue playing. 31. [NEXT] Press to skip to play the next track. 32. [A-B/PHONE PAIR] Press to setup A-B repeat playing. Under Bluetooth mode, press this button to pair a Bluetooth cell phone with the unit 33.
Brake Control It is necessary to connect the Brake Control wire to the Hand-brake switch of the car. While driving, the TFT monitor will display the alarm picture (see as follows) in order to ensure the safety. Under the Rear View Mode, the Brake Control function is no effective.
MAIN MENU RADIO OPERATIONS Touch the icon “RADIO” to enter the 1st operation page of RADIO Mode: Touch the icon “MORE” to enter the 2nd page of main menu: 1~6. STORED CHANNEL Manual Store Radio Station Hold on touching the icon, you can store current radio frequency to the stored channel. For example, the current frequency is 98.5MHZ, by hold on touching the icon 1, you can store the radio station of 98.5MHZ to the channel 1. After manual store radio station, the former stored stations will be instead.
Press any button to stop seeking. Seeking will stop automatically when seek an available channel then play this station. The unit will stop on the beginning frequency if no available station after seeking one cycle. Hold on pressing [>] / [<] buttons of remote control to perform same operation. 4. NEXT PAGE Touch the icon to enter the 3rd page of RADIO Mode: 10.
3. MENU Touch the icon to return the main menu. 4. NEXT PAGE Touch the icon to return to the 1st page of RADIO Mode. Radio Data System Operation Touch the icon of AF to enter the RDS Mode: 5. AF (ALTERNATIVE FREQUENCY) Touch this icon or press the [AF] button to activate/deactivate the AF function. When receiving conditions become bad, a station with better receiving conditions is automatically tuned into.
buttons to move the cursor to TA VOLUME, then press [<] / [>] buttons to adjust the volume. No matter how loud the volume is in the other mode, it will broadcast the traffic announcement in the same sound level. When listening to the traffic announcement, use the volume button to adjust the level, but if the volume is louder than the TA initialization volume level, it will not be possible to adjust the volume. When the signal of the Traffic-Program identification (TP) is bad, there will be a beep sound.
7. STOP During movie playback, touch the icon once; the DVD player memorizes the location where you stopped (touch the [PLAY] icon to resume playing from the memorized location). If you touch the icon twice, the playback will start from the beginning of the disc when you touch the [PLAY] icon. Press the [STOP] button of remote control to perform the same operation. 8. NEXT PAGE Touch the icon to enter the 2nd page of DVD Mode. 8. NEXT PAGE Touch the icon to enter the 1st page of DVD Mode.
1~6. STORED CHANNEL Manual Store TV Station Hold on touching the icon, you can store current station to the stored channel. For example, the current station is 3 CH, by hold on touching the icon 1, you can store the radio station of 3 CH, to the channel 1. After manual store TV station, the former stored stations will be instead. The number icons 1 to 6 represent the stored stations. Hold on pressing the number buttons 1~6 on the panel to perform same operation.
2. SYSTEM Touch the icon to switch the TV system as follow: NTSC – PAL/BG – PAL/I – PAL/DK – NTSC 3. MENU Touch the icon to return to main menu. 1. The Number of Playing Song 2. The Total Songs in Play List 3. The Playing Time 4. The Name of Playing Song 4. NEXT PAGE Touch the icon to enter the 1st page of TV Mode. 5. The Name of Artist * Select the Station Directly Press the number buttons of remote control to select the station directly.
Video Operation AV IN OPERATIONS Touch the icon “AV IN” to enter the AV IN Mode: 1. MUTE Touch the icon to mute the sound; touch it again to resume to the previous volume level. 2. MUSIC Touch the icon to switch to the MUSIC operation. 3. MENU Touch the icon to return the main menu. 4. EXIT Touch the icon to exit the TOUCH ICONS display. 1. MUTE Touch the icon to mute the sound; touch it again to resume to the previous volume level. 2.
BLUETOOTH OPERATIONS SETTINGS Touch the BLUETOOTH icon to enter the Bluetooth mode: 2. PHONE CALL Touch the icon to enter the phone calling. 3. PHONE BOOK Touch the icon to enter the phone book lookup. 4. AUDIO Touch the icon to enter the audio device operation. 5. SETTINGS Touch the icon to enter the Bluetooth settings.
5. AUDIO PAIRING Touch the icon, then see the below message on information display: PHONE CALL Then set the audio device to pair it with the unit. Touch the icon again to cancel the pairing, and see the below message on information display: When pairing finished, set the audio device to connect it with the unit, then you can see the audio device name on information display. Press the [MUSIC PAIR] button of remote control under SETTINGS page to perform same operation. 6.
CALLING OUT When call out, you will see the below information: PHONEBOOK Then when talking, you will see the below information: And end the call, you will see the below information: CALLING IN When call in, you will see the below image: During conversation, you will see the below image: < < NOTE: Touch the icon 7~11, to select the item; touch it again to activate the operation.
AUDIO 8. SIM PHONEBOOK The Simbook stored in the paired phone. 9. DIALLED CALL The dialled calls stored in the paired phone. 10. RECEIVED CALL The received calls stored in the paired phone. 11. MISSED CALL The missed calls stored in the paired phone. Touch the icon to enter the phonebook, you will see the below image: 1. PREVIOUS Touch the icon to select the previous track. Press the [PREVIOUS] button of remote control to perform same operation. 2. NEXT Touch the icon to select the next track.
SYSTEM SETUP SYSTEM SETUP Touch the icon “SETUP” or press the [SYSTEM] button of panel to enter the SETUP of system parameters: RADIO AREA: TV AREA: BLUETOOTH: DEFAULT: USA – JAPAN – OIRT – EUROPE – ASIA – USA US – CCIR – IT – AUS – NZ – US OFF – ON – OFF The unit will restore all default settings of Sound Parameter, Picture Parameter & Tuner Parameter. VIDEO SETUP 1. SYSTEM SETUP 2. VIDEO SETUP 3. AUDIO SETUP 4. MAUD SETUP (More Audio) 5.
AUDIO SETUP BASS: TREBLE: BALANCE: FADER: - 15 ~ + 15 - 15 ~ + 15 L 15 ~ R 15 F 15 ~ R 15 MAUD SETUP (MORE AUDIO SETUP) EQ: LOUDNESS: SUB-WF FRQ: SUB-WF VOL: 54 CLOCK SETUP CLOCK: DISPLAY: HOUR: MINUTE: 12H / 24H ON / OFF 00 ~ 23 00 ~ 59 USER – POP – CLASSIC – ROCK – JAZZ – USER OFF-400HZ-800HZ-2400HZ-OFF 80HZ-120HZ-160HZ-OFF 0 -15 55
DVD SETUP MENU SYSTEM MENU SETUP MENU OPERATION < < < < < < < < Press the [SETUP] button of remote control to enter the DVD SETUP Menu. Press the [<] / [>] buttons to switch the main menus as following: SYSTEM – LANGUAGE – AUDIO – VIDEO – SPEAKER – DIGITAL Press the [ ] / [ ] buttons to enter the submenus from main menus. Press the [ ] button on the top submenu or press the [ ] button on the bottom of submenu to exit the submenus to main menus.
LANGUAGE SETUP OSD LANGUAGE Following options are available for the OSD LANGUAGE: ENGLISH GERMAN SPANISH FRENCH ITALIAN RUSSIAN DUTCH SWEDISH DANISH NORWEGIAN POLISH HUNGARIAN AUDIO LANGUAGE Following options are available for the AUDIO LANGUAGE: ENGLISH GERMAN SPANISH FRENCH ITALIAN RUSSIAN DUTCH SWEDISH DANISH NORWEGIAN POLISH HUNGARIAN SUBTITLE LANGUAGE Following options are available for the SUBTITLE LANGUAGE: ENGLISH GERMAN SPANISH FRENCH ITALIAN RUSSIAN DUTCH SWEDISH DANISH NORWEGIAN POLISH HUNGARIAN
BRIGHTNESS Following options are available for the BRIGHTNESS: 0 2 4 6 8 10 12 DIGITAL SETUP CONTRAST Following options are available for the CONTRAST: 0 2 4 6 8 10 12 HUE Following options are available for the HUE: -6 -4 -2 0 +2 +4 +6 SATURATION Following options are available for the SATURATION: 0 2 4 6 8 10 12 SPEAKER SETUP OP MODE Following options are available for the OP MODE: LINE OUT RF REMOD DYNAMIC RANGE Following options are available for the DYNAMIC RANGE: FULL 6/8 4/ 8 2 /8 OFF DUAL MONO F
TROUBLESHOOTING Problem If any of problem persists after checking the below list, Please consult your nearest service dealer. Never attempt to disassemble and repair unit personally.
Problem Cause Corrective Action SPECIFICATIONS MP3 Interruption occurred during playback Disc is dirty or scratched Clean disc or replace File is damaged/bad recording Recreate disc with good files Rear Power Output Message is longer than LCD can display Equalizer Control Range Signal to Noise Ratio: Error Messages Line Input Line Output Cause Loading Disc is being read Clean disc with soft cloth Disc is upside down Insert disc with label side up Disc not present in loading compartment In
Performance Products Ltd Cleaver House, Sarus Court, Manor Park, Runcorn WA7 1UL UK www.snooper.
