Operation Manual

9
2. Using the Mounting Bracket and Screws
Your S6 can be installed easily with screws if you have a sufficiently flat
area on your dashboard or centre console.
- Having decided where to mount your unit, using the mounting bracket
as a guide, mark and drill the mounting holes.
- Screw the mounting bracket in place
using the screws provided.
- Finally slide the control panel onto
the mounting bracket and plug the
end of the lead of the GPS
antenna already mounted,
into the socket marked
’ANTENNA’ on the side of
the control panel.
- See Page 10 for details of how to
connect power to your unit.
3. Using the Windscreen Suction Cup bracket
If you prefer you can mount the S6 to the inside of your vehicles
windscreen using the suction cup bracket provided. Simply select a
position within the windscreen remembering that you need to connect the
power and RLD (if required) connection cables as well as the extension
GPS antenna.
- Install the suction cups onto the bracket by fitting them into its holes (A).
- Clean the area where you wish to position the bracket thoroughly with a
good quality glass cleaner.
- Carefully bend the bracket so that when it is
mounted on to the windscreen with the S6
Control Panel attached, the Control Panel is
facing in the desired direction so that you
can easily see the LCD display and
safely operate the controls.
- Slide the Control Panel onto
the bracket until it is secure (B).
- To remove the Control Panel
simply slide the unit off the bracket from
the front.
-
Plug the end of the lead of the GPS
antenna
already mounted, into the socket
marked ’ANTENNA’ on the side of the
control panel.
- See Page 10 for details of
how to connect power to
your unit.
E
A
R
P
H
O
N
E
R
D
A
N
T
E
N
N
A
EARPHONE
R
D
A
N
TEN
N
A
A
B
To activate or de-activate the Satellite Counter setting follow these
instructions.
From the Standby screen press the button below ’Menu’ on the LCD
display and then using the buttons below the Up and Down arrows, scroll
the display until ’SATELLITE COUNTER is highlighted and press ’Select’.
Then using the buttons below the arrows on the display, highlight your
desired setting, either ’ON’ or ’OFF’. Once you have made your choice
press the ’Select’ button. The screen will read ’SETTING CONFIRMED’ to
confirm your selection and will return to the Menu screen.
Note: To return to the Menu screen from the Sub Menu screen, press
the button below ’Back’ (2) on the display. To return to the Standby
screen from the Menu screen press the same button, which will now say
Cancel . If no buttons are pressed on the device for a period of five
seconds the screen will automatically return to the Standby display.
12. Adjusting the volume
The S6 has an adjustable volume
for controlling the loudness of the
audible alert. To increase the
volume simply press button 8 (+)
on the control panel. To decrease
the volume press button 7 (-) on
the control panel. The display will
give you a visual confirmation of
the volume set.
13. Adding and deleting new locations
It is possible to add and edit your own personal locations on your
Snooper S6 GPS control panel. To add a new location simply press the
’New Location’ (6) button on the device whilst you are at the location you
have chosen to select. To view your saved co-ordinates press the ’Menu’
button and using the buttons below the arrow icons (3 & 4) scroll up or
down until ’EDIT MEMORY’ is highlighted and press ’Select’. Any
co-ordinates stored will be listed in numerical order - MEM01, MEM02,
MEM03 etc. These co-ordinates can be uploaded for verification if
necessary (See ’Uploading’ page 6). If you wish to delete any
co-ordinates simply use the up or
down buttons to highlight the location
you would like to look at and press
the ’Select’ button (5). You can save
up to 99 personal locations in total.
28
7
VOLUME 3
8
5
MEM Ø1
N 53
0
11' 31"
W 002
0
51' 06"
BACK
DELETE
SUB MENU