Operation Manual

12
Installation S6-RLD
If you have purchased the S6-R or have purchased the S6-RLD as an
optional extra to your S6 you will need to refer to the following
instructions to install the S6 remote extension radar and laser detector.
This device is waterproof so can be installed under the bonnet behind the
vehicles grille or within an air intake at the front of your car or you can
simply mount the device on the dashboard or windscreen of your vehicle.
Please note however that some vehicles including Renault, Citroen and
Peugeot may come with a ’Heat Reflective’ or ’Comfort’ front windscreen,
which may affect the performance of the S6-RLD. In these cases the RLD
must be mounted outside the vehicle. For this type of installation follow
the instructions for S6-RLD External Installation.
1. Dashboard Mounting
The S6 RLD needs a clear view of the road ahead and needs to be
positioned in as horizontal a position as possible. If you can find a
position on the dashboard that is fairly flat (surface must be within 15-20
degrees of the road) and so that the view from the front of the detector is
through clear glass and is not obscured by any metallic objects such as
the windscreen wipers, the Hook and Loop fastener might provide the
easiest method of mounting the detector. To mount the RLD in this way
follow these instructions.
- Use a damp cloth to thoroughly clean
the bottom of the S6-RLD and the area
where you intend to mount the device.
- With the two parts of the Hook and
Loop fastener still fastened together,
peel the backing tape from the softer
’Loop’ side of the fastener and
apply it to the bottom of the unit.
- Next remove the backing tape
from the ’Hook’ side of the
fastener, again whilst the
two parts are still fastened
and position the unit onto the
desired area. Please note it
will take approximately 24hrs for
the Hook and Loop fastener to
adhere properly to the dashboard
and unit.
- Finally feed the cable from the S6-RLD to
the S6 GPS control panel, concealing it as
well as possible and plug it into the socket
marked ’RD’ on the side of the control panel.
25
To change the Logic Mode setting follow these instructions.
From the Standby screen press the button below ’Menu’ on the LCD
display and then using the buttons below the Up (3) and Down (4)
arrows, scroll the display until
’SAFETY CAMERAS’ is highlighted
and press ’Select’ (5). Then using the
buttons below the arrows on the
display, highlight the features you
would like to set, either ’SET LOGIC
MODE’ or ’SET SMART MUTE ’and
press ’Select’. Next highlight your
preferred Logic Mode by again using
the up or down arrows. Once you have
made your choice press the ’Select’
button. The screen will read ’SETTING
CONFIRMED’ to confirm your selection
and will return to the Menu screen.
Note: To return to the Menu screen
from the Sub Menu screen, press
the button below ’Back’ (2) on the
display. To return to the Standby
screen from the Menu screen press
the same button, which will now say
Cancel . If no buttons are pressed on the device for a period of five
seconds the screen will automatically return to the Standby display.
Smart Mute - The Smart Mute setting has been designed so that you
only receive a visual alert generated by the S6 GPS control panel if you
are travelling below the posted speed limit as you approach a given
location such as a Gatso camera. If you are travelling above the posted
speed limit you will receive both a visual and an audible alert as normal.
The Smart Mute setting also activates a radar/laser filter designed to filter
out any radar/laser signals you should encounter whilst travelling below
20mph.
To activate the Smart Mute setting follow these instructions.
From the Standby screen press the
button below ’Menu’ on the LCD
display and using the buttons below
the Up (3) and Down (4) arrows on
the screen, scroll the display until
’SAFETY CAMERAS’ is highlighted
and press ’Select’ (5). Then using the
buttons below the arrows on the
display, highlight ’SET SMART MUTE’
and press ’Select’. Use the up or down
arrows to highlight your desired setting, either ’ON’ or ’OFF’. Once you
2 3 4 5
SET LOGIC MODE
SET SMART MUTE
LOGIC MODE 1
LOGIC MODE 2
LOGIC MODE 3
2 3 4 5
2 3 4 5
ON
OFF
BACK
SELECT
SUB MENU
BACK
SELECT
SUB MENU
BACK
SELECT
SUB MENU