Owner / Operator’s Manual This Manual Must Be Read Before Operating The Equipment SL-80 Serial # PB-200036 and higher SL-80SS Serial # PC-200048 and higher CUSTOMER COPY Madison Heights, Michigan 48071 800-725-8377 www.turfexproducts.
Table of Contents General Information....................................................................................................................................................................................... 3 Introduction .................................................................................................................................................................................................. 4 Safety ........................................................................
CONGRATULATIONS! The spreader you have purchased is an example of snow and ice control technology at its General Information Your spreader’s self-contained design is a trademark of all Snowex products. Here’s why... SIMPLICITY: Fewer moving parts manufactured of higher quality means minimal maintenance for your SnowEx spreader.
Introduction This manual has been designed for your help. It will assist you and instruct you on the proper set-up, installation and use of this spreader. Refer to the table of contents for an outline of this manual. We require that you read and understand the contents of this manual completely (especially all safety information) before attempting any procedure contained herein.
Safety Before attempting any procedure in this book, these safety instructions must be read and understood by all workers who have any part in the preparation or use of this equipment. For your safety warning and information decals have been placed on this product to remind the operator of safety precautions . If anything happens to mark or destroy the decals, please request new ones from SnowEx. Remember, most accidents are preventable and caused by human error.
Operational Safety Information Summary of Important Safety Information Chemical accident procedures Immediate response is necessary in the event of sprayer leaks, bodily chemical contact, poisoning, or spills. See instructions below: Sprayer Leak Bodily chemical contact Poisoning by ingestion or inhalation Chemical spills 6 If the sprayer develops a leak, immediately stop spraying. Turn off power to the sprayer and follow directions below, as applicable.
Operational Safety Information Summary of Important Safety Information Listed below is a summary of safety information of particular importance. See individual sections of this owner’s manual for more details. DURING ASSEMBLY Check and test completed assembly as directed in this manual. Serious injury could result from chemical leaks if sprayer is improperly assembled. DO NOT MODIFY SPRAYER DESIGN DURING OPERATION • Read and follow each chemical label’s instructions and warnings.
Operational Safety Information Summary of Important Safety Information DURING SPRAYING • • • • • • • • • o not over-apply. Apply at rate recommended by chemical manufacturer. D Do not eat, drink, smoke, rub your eyes or touch your bare skin while handling chemicals and spraying. Never point the spray gun at people or animals. Do not spray near open flames or sources of heat. Always hold the spray gun firmly when using it to spray at higher pressures in order to prevent gun from whipping.
Sprayer Operation Model # SL-80/SL-80SS 1) F ill sprayer with material through top hole. Caution: Always use gloves and safety goggles when filling sprayer. 2) Place valve in position for desired use. 3) If using spray wand never point at objects (ie: humans, vehicles etc.) 4) If using spray nozzle keep away from objects (ie: humans, vehicles etc.) at least 10 feet. 5) When not moving or spraying place switch in off position.
Sprayer Operation & Electrial Schematic Model # SL-80/SL-80SS 1) Charge battery after each use. Disconnect harness and connect to battery charger as shown below. Then plug charger into 110v outlet.
Troubleshooting & Maintenance Model # SL-80/SL-80SS Whenever service is necessary, your local SnowEx Dealer knows your Sprayer best. Take your Sprayer to your local dealer for any maintenance or service needs on your unit. If this is not possible, the Troubleshooting Guide below may assist you in identifying the problem. Warning: First read all warning instructions and safety messages before servicing your Sprayer. Preliminary Checks • Be sure all electrical connections are tight and clean.
Warranty Warranty Limited Warranty Snowex products are warranted for a period of two years from the date of purchase against defects in material or workmanship under normal use and service, subject to limitations detailed below. Warranty period of two years begins on the date of purchase by the original retail user. The WARRANTY REGISTRATION CARD must be returned to the manufacturer for this warranty to become effective. This warranty applies to the original retail purchaser only.
Key to Parts D5377 Hose Barb | 1/2” Male Thread X 3/8” 90° D5381 Hose Barb | 1/4” Male Thread X 3/8” D5384 Decal | Quality Made In The USA D5387 Decal | Serial Number | SL-80 D5388 Decal | Serial Number | SL-80SS D5901 Hopper Frame | SL-80 D5904 Wheel 13” X 5” D5906 Frame Stand | SL-80 D5908 Handle | SL-80 D5915 Axle D5917 Handle Grip D5919 Cotter Pin | 2” Stainless D5923 Wheel Bushing D5943 Bolt | 1/4”-20 X 2-1/4” Hex D5994 Grease Fitting D6024 Shaft Collar D6131 Bolt | 1/4”-20 X 1/2” Serr.
Handle Assembly Parts Breakdown Model # SL-80 2 4 3 9 5 8 1 11 13 10 12 6 7 14 © TrynEx International 2013 (REV B) F50775
Handle Assembly Parts Breakdown Model # SL-80 BOM ID 1 2 3 4 Description D5908 D5917 D6132 D6406 Qty 1 2 1 1 © TrynEx International 2013 (REV B) F50775 BOM ID 5 6 7 8 Description F50001 F50008 F50016 F50106 Qty 1 1 1 1 BOM ID 9 10 11 12 Description F50107 F50112 T15016 T15018 Qty 1 BOM ID 13 Description T20307 Qty 1 2 1 2 15
Handle Assembly Parts Breakdown Model # SL-80SS 1 3 2 6 8 13 10 7 12 11 9 5 4 16 © TrynEx International 2013 (REV B) F50775
Handle Assembly Parts Breakdown Model # SL-80SS BOM ID 1 3 4 5 © TrynEx International 2013 (REV B) F50775 Description D5917 D6406 F50008 F50016 Qty 2 1 1 1 BOM ID 6 7 8 9 Description F50020 F50106 F50107 F50112 Qty BOM ID 1 10 11 12 13 1 1 2 Description T15016 T15018 T20307 T30153 Qty 1 2 1 1 17
Tank Assembly Parts Breakdown Model # SL-80 17 13 15 14 2 16 5 1 12 3 18 9 12 12 19 8 11 6 10 7 4 7 4 18 © TrynEx International 2013 (REV B) F50775
Tank Assembly Parts Breakdown Model # SL-80 ID # 1 2 3 4 5 6 7 Part # D5377 D5381 D5901 D5904 D5906 D5915 D5919 © TrynEx International 2013 (REV B) F50775 Qty 1 1 1 2 1 1 2 ID # 8 9 10 11 12 13 14 Part # D5923 D5943 D5994 D6024 D6854 F50009 F50011 Qty 4 4 2 2 3 1 1 ID # 15 16 17 18 19 Part # F50013 F50108 F50487 F50651 T15016 Qty 1 1 1 1 4 19
Tank Assembly Parts Breakdown Model # SL-80SS 15 13 11 12 14 16 2 1 18 19 7 10 3 17 3 5 4 20 9 6 8 5 © TrynEx International 2013 (REV B) F50775
Tank Assembly Parts Breakdown Model # SL-80SS ID # 1 2 3 4 5 Part # D5377 D5381 D5904 D5915 D5919 Qty 1 1 2 1 2 © TrynEx International 2013 (REV B) F50775 ID # 6 7 8 9 10 Part # D5923 D5943 D5994 D6024 D6854 Qty 4 4 2 2 3 ID # 11 12 13 14 15 Part # F50009 F50011 F50013 F50108 F50487 Qty 1 1 1 1 ID # 16 17 18 19 Part # F50651 T15016 T30151 T30152 Qty 1 4 1 1 1 21
Pump Assembly Parts Breakdown Model # SL-80 11 12 6 17 2 3 4 13 14 19 8 19 2 18 15 9 21 5 16 10 2 1 7 2 20 22 © TrynEx International 2013 (REV B) F50775
Pump Assembly Parts Breakdown Model # SL-80 ID # 1 2 3 4 5 6 7 8 Part # D5377 D6131 D6132 D6172 D6988-16.
Pump Assembly Parts Breakdown Model # SL-80SS 14 19 9 2 3 6 2 16 17 4 12 15 8 18 11 2 21 10 13 2 5 1 24 19 7 2 20 © TrynEx International 2013 (REV B) F50775
Pump Assembly Parts Breakdown Model # SL-80SS ID # 1 2 3 4 5 6 7 © TrynEx International 2013 (REV B) F50775 Part # D5377 D6131 D6132 D6172 D6988-16.
Notes 26 © TrynEx International 2013 (REV B) F50775
Notes © TrynEx International 2013 (REV B) F50775 27
132503
