Owner / Operator’s Manual This Manual Must Be Read Before Operating The Equipment SP-65 Serial # PA-201033 and higher CUSTOMER COPY Madison Heights, Michigan 48071 800-725-8377 www.snowexproducts.
Table of Contents General Information ...................................................................................................................................................................................... 3 Introduction .................................................................................................................................................................................................. 4 Safety ........................................................................
General Information CONGRATULATIONS! The SnowEx product you have purchased is an example of snow and ice management product at its finest! Your SnowEx product’s self contained design is a trademark of all SnowEx products. Here’s why... SIMPLICITY: Fewer moving parts manufactured of higher quality means minimal maintenance for your SnowEx product. RELIABILITY: High impact linear low density polyethylene hopper, custom engineered powder coated frame.
Introduction This manual has been designed for your help. It will assist you and instruct you on the proper set-up, installation and use of this product. Refer to the table of contents for an outline of this manual. We require that you read and understand the contents of this manual completely (especially all safety information) before attempting any procedure contained in this manual. Extra copies of Owner / Operator Manuals can be purchased at your SnowEx Dealer.
Safety Before attempting any procedure in this book, these safety instructions must be read and understood by all workers who have any part in the preparation or use of this equipment. For your safety warning and information decals have been placed on this product to remind the operator of safety precautions . If anything happens to mark or destroy the decals, please request new ones from SnowEx. Remember, most accidents are preventable and caused by human error.
Spreader Operation Model # SP-65 SPREADER LOADING Capacity: 1.5 Cubic Foot Hopper Do not overload spreader. Weights of material are an average for dry materials. Material Weight Per Cubic Ft. Rock Salt 80-90 lbs. Sand/Salt Mix 95-120 lbs. Never remove spreader from vehicle with material in it as this could cause damage to the frame assembly. Never leave materials in hopper for long periods of time, salt is hygroscopic and will attract atmospheric moisture and harden up.
Assembly Instructions Model # SP-65 STEP 1 Open Box. Remove the Axle/Spinner Assembly. Slide the Shaft Collars from the hardware kit onto the axle - one on each side of the Gearbox One Hole in Axle – Left. STEP 2 Slide the Hopper Frame Assemblies over the Axle – one on each side of the Gearbox. One Hole in Axle – Left. STEP 3 Install Drive Wheel. Slide the 2” Cotter Pin through both the wheel and axle.
Assembly Instructions Model # SP-65 STEP 4 Install the other Wheel. Slide the 1.5” Cotter Pin through the Axle, outside the Wheel. STEP 5 Install Frame Stand. Attach to the Hopper Supports. STEP 6 Install Hopper. Put Bolts with Washers through all four holes in Hopper and Frame. Thread on the Nuts. STEP 7 Put Agitator Pin through Spinner Shaft inside hopper. STEP 8 Bolt Cable to both handles. It should be positioned so the cable points toward the base of the handle and will be to the operator’s left.
Assembly Instructions Model # SP-65 STEP 9 Put bolt through both handles at the base. Hand-Tighten only. STEP 10 Put Handle Assembly onto frame. Insert Bolts. Hand-Tighten. STEP 11 Tighten Bolts holding the handle together, then tighten the bolts holding the handle to the frame. STEP 12 Put Cable Lever into Off position. Pull Gate as far back as possible. Attach Cable to Gate.
Assembly Instructions Model # SP-65 STEP 13 Install Cable Clip to cable bracket. COMPLETE.
Troubleshooting Model # SP-65 TOO MUCH MATERIAL FLOW GATE STUCK OPEN LUBRICATE GATE SLIDES DROP SPREADER: ADJUST FRONT GATE SLIDE ADJUST GATE STOP LUBRICATE LINKAGE REMOVE AND CLEAN IF BROKEN, REPLACE CABLE STUCK LUBRICATE REPLACE RECONNECT ACTUATOR / LINKAGE NOT ENOUGH MATERIAL FLOW POOR SPREAD PATTERN HANDLE DOES NOT WORK ADJUST/REPLACE HARDWARE / HANDLE PHYSICAL OBSTRUCTION REMOVE GATE STUCK CLOSED (SEE ABOVE) AGITATOR IN PLACE NO: REPLACE EMPTY HOPPER FILL WITH MATERIAL SCREEN BLO
Warranty Limited Warranty Snowex products are warranted for a period of two years from the date of purchase against defects in material or workmanship under normal use and service, subject to limitations detailed below. Warranty period of two years begins on the date of purchase by the original retail user. The WARRANTY REGISTRATION CARD must be returned to the manufacturer for this warranty to become effective. This warranty applies to the original retail purchaser only.
Key to Parts Model # SP-65 A4014 Hardware Kit | Handle D5936 Gate Stop Spring A4185 Hardware Kit D5938 Spring Pin | 5/32” X 3/4” D5292 Washer | #10 Flat Stainless D5939 Spring Pin | 5/32” X 1” D5345 Gate Slide D5941 Axle Spacer D5384 Decal | Made In The USA D5948 Nut | #10-32 Nylox Stainless D5389 Decal | Serial Number D5967 Hopper Cover D5902 Spinner D5971 Wheel D5905 Bolt | #10-32 X 1/2” Hex Head D5973 Top Screen D5909 Gear | Axle D5974 Hopper Frame Leg D5910 Gear | Sp
Hopper Assembly Parts Breakdown Model # SP-65 12 13 14 5 4 17 1 18 3 16 15 6 9 4 7 11 2 10 8 14 © TrynEx International 2013 (REV B) F50753
Hopper Assembly Parts Breakdown Model # SP-65 ID # 1 2 3 4 5 6 7 8 9 10 © TrynEx International 2013 (REV B) F50753 Part # D5292 D5345 D5361 D5905 D5907 D5912 D5927 D5928 D5935 D5936 Qty 2 1 1 6 4 1 1 1 ID # 11 12 13 14 15 16 17 18 Part # D5948 D5967 D5973 D5981 D5982 F50772 T15014 T15016 Qty 4 1 1 1 1 1 4 4 1 1 15
Axle Assembly Parts Breakdown Model # SP-65 18 21 22 37 19 16 13 1 18 3 11 5 12 8 11 20 21 17 9 11 7 14 10 15 17 16 6 2 8 19 20 4 © TrynEx International 2013 (REV B) F50753
Axle Assembly Parts Breakdown Model # SP-65 ID # 1 2 3 4 5 6 7 8 Part # D5902 D5909 D5910 D5911 D5913 D5915 D5919 D5921 © TrynEx International 2013 (REV B) F50753 Qty 1 1 1 2 1 1 1 2 ID # 9 10 11 12 13 14 15 16 Part # D5923 D5926 D5930 D5938 D5939 D5941 D5947 D5956 Qty 4 ID # 1 17 18 3 19 1 20 1 21 22 1 Part # D5971 D5974 D5993 D5994 D6024 D6090 Qty 2 2 1 2 2 2 1 1 17
Handle Assembly Parts Breakdown Model # SP-65 5 11 12 1 7 9 6 8 3 2 13 13 4 6 13 10 18 © TrynEx International 2013 (REV B) F50753
Handle Assembly Parts Breakdown Model # SP-65 ID # 1 2 3 4 5 6 7 © TrynEx International 2013 (REV B) F50753 Part # D5365 D5384 D5389 D5907 D5917 D5943 D5948 Qty 2 1 1 2 2 5 2 ID # 8 9 10 11 12 13 Part # D5975 D5976 D5977 D5983 D5990 T15016 Qty 1 1 1 1 1 7 19
Notes 20 © TrynEx International 2013 (REV B) F50753
Notes © TrynEx International 2013 (REV B) F50753 21
Notes 22 © TrynEx International 2013 (REV B) F50753
Notes © TrynEx International 2013 (REV B) F50753 23
131903
