socketmobile.com D700 USERGUIDE DURASCANTM Bluetooth® wireless technology Barcode Scanner Model D700 www.socketmobile.
TABLE OF CONTENTS Package Contents 4 Product Information 5 Scanner Setup 6 Charging the Battery 7 Optional Charging Accessories 8 Powering Scanner On/Off 9 Scanning Barcodes 10 Bluetooth Connection Modes 11 Setup without software application (Basic Mode): • Android 13 • Apple® 14
TABLE OF CONTENTS Setup using Application Mode: • Android or Windows mobile device 15 • Windows PC 18 • Apple® iOS 20 Unpairing Bluetooth Connection 22 Bluetooth Reconnection of Scanner 23 Scanner Status Indicators 24 Product Specifications 28 Helpful Resources 30 Safety, Compliance & Warranty 31-41 Battery Warning 36-37 Changing the Scanner Settings (Command Barcodes) 41
PACKAGE CONTENTS DuraScan D700 Lanyard USB A to USB Type-C Cable Thank you for choosing Socket Mobile! Let’s get started! © 2017 Socket Mobile, Inc. All rights reserved. Socket®, the Socket Mobile logo, SocketScan™, DuraScan™, Battery Friendly® are registered trademarks or trademarks of Socket Mobile, Inc. Microsoft® is a registered trademark of Microsoft Corporation in the United States and other countries.
PRODUCT INFORMATION Scanner head Scan Indicator Light Product label Bluetooth Light (Blue) Battery Light (Green/Yellow/Red) Trigger button Power button* Power Connector Stand Attachment Lanyard Eyelet Charging pins The D700 has a protection rating of IP54 for dust and water protection. It is also made with antimicrobial to help provide protection against bacteria. *Also used to display the on-screen keyboard in Basic Mode (iOS only).
SCANNER SETUP Attach the Lanyard (optional) 1. Detach the string loop of the tether from the lanyard. 2. Feed the string loop through the eyelet. 3. Pull the tether through the string loop. 4. Pull tight so the string loop is secure. 5. Reattach the string loop’s tether to the lanyard.
CHARGE THE BATTERY Power Adapter Rubber Flap To open The scanner must be fully charged before first use. Please allow 6 hours uninterrupted charging for the initial battery charge. Lift the rubber flap to access the power connector. • Yellow Light = Charging • Green Light = Fully charged Important: Charging from a computer USB port is not reliable and not recommended.
OPTIONAL CHARGING ACCESSORIES Available separately. Charging Cradle Charging Stand AC Power Supply International Adapters available For all optional accessories visit our Socket Store.
POWERING ON/OFF Power button Powering On: Powering Off/ Disconnecting: Press and hold down the small power button until the Battery light turns on and the scanner beeps twice (low-high). Press and hold down the small power button until the scanner beeps twice (high-low) and all lights turn off. The scanner will power off automatically if device is not connected within 5 minutes. Scanner connected to a device will power off within 2 hours if idle/inactive.
SCANNING BARCODES 1D Barcode Aim the scan beam straight across the entire barcode. Trigger button Scanning Barcodes 1. Hold the scanner a few inches from the barcode. 2. Aim, press and hold the trigger button. By default, the scanner will beep, vibrate, and the scan indicator will flash green to confirm a successful scan. Caution: Do not stare directly into the scanner’s light beam.
BLUETOOTH CONNECTION MODES Connect your scanner using one of the following Bluetooth connection modes: Bluetooth Connection Profiles Bluetooth Mode Description Basic Mode (HID) (Default)* • NO software installation needed • Connects to most devices • Good for barcodes containing small amounts of data • Scanner interacts with host device like a keyboard Human Interface Device Profile For Android or Windows Application Mode 1. Software installation is required (SPP) 2.
BLUETOOTH CONNECTION MODES Operating System Connection Options Devices Bluetooth HID Support Bluetooth SPP Support Bluetooth Apple Serial Specific (MFi Mode) Android Android 4.0.3 & later Yes Yes N/A Apple iOS iPod, iPhone, & iPad Yes N/A Yes Windows Mobile Windows Mobile 6.x (SoMo only) Yes Yes N/A Windows PC Windows 7, 8, 10 Yes Yes N/A Mac OS Mac OS X 10.4 to 10.
BASIC MODE Android: Connect Android Device in Basic Mode In this mode the scanner functions and communicates similar to a keyboard. Therefore, scanner will work with Notes, and any other application that supports an active cursor. 1. Power on the scanner. Make sure the scanner is discoverable (unpaired) and the blue light blinks fast. 2. Settings | Bluetooth. 3. Make sure the device has Bluetooth “On” to scan for devices. 4. In the list of found devices, select D700 [xxxxxx]. Tap Pair. 5.
BASIC MODE Apple: Connect Apple iOS Device or Mac OS Device Basic Mode In this mode the scanner functions and communicates similar to a keyboard. Therefore, scanner will work with Safari, Notes, and any other application that support an active cursor. 1. Power on the scanner. Make sure the scanner is discoverable (unpaired). The Blue light blinks fast. 2. Start a Bluetooth device search. • Settings | Bluetooth: Turn on Bluetooth and search for device. • Mac OS: Click System Preferences | Bluetooth.
APPLICATION MODE Connect Android or Windows Mobile Device: In this mode the scanner functions and communicates similar to a keyboard. Therefore, scanner will work with Notes, and any other application that support an active cursor. Highly recommended, allows two-way communications with Android, or Windows Mobile Devices. Scanner-enabled app software installation required. 1. Power on the scanner and scan this barcode. The scanner will beep 3 times. Make sure the scanner is discoverable (unpaired).
APPLICATION MODE Connect Android device in Application Mode using EZ Pair Install Software 1. Go to Store, search for “SocketScan”. 2. Download & install. Follow the on screen instructions. Getting Started 3. Follow the on screen instructions 1 through 4. 4. Tap on screen the ON SCREEN button. 5. Tap on screen the 1D SCANNER button 6. Scan the barcode on the device screen. Wait a few seconds. The scanner will beep 3 times indicating it has accepted the command to connect to your device. 7.
APPLICATION MODE Connect Windows PC in Application Mode Note: Make sure you have administrative privileges. 1. Download the latest SocketScan 10 software from Socket Mobile’s support web page. 2. Follow the on-screen instructions to install the software. 3. In SocketScan 10 Settings, select an incoming Bluetooth serial COM port. Note: If there is none please click Ports to create at least one new incoming COM port in Bluetooth settings. 4. Click Finish.
APPLICATION MODE To pair the scanner with Windows PC using EZ Pair: 1. Power on the scanner. Make sure the scanner is available to be connected to Bluetooth (unpaired). 2. Launch SocketScan 10 and click on the SocketScan 10 icon in the task tray. In the pop-up menu, click Socket EZ Pair. 3. Click 1D scanner accordingly. 4. Scan the barcode that appears on the screen. 5. The PC will automatically try to pair with the scanner. If prompted to allow the pairing, click “Yes”.
APPLICATION MODE Connect Apple iOS device in Application Mode Please check with your scanner application vendor or visit www.socketmobile.com/appstore to confirm your scanner-enabled application supports the scanner. If you are using the scanner with an Apple iOS device and a scanner-enabled Application that does not provide instructions how to connect your scanner, please use the following steps. 1. Power on the scanner. Make sure the scanner is discoverable (unpaired).
APPLICATION MODE 4. Tap Socket D700[xxxxxx] in the list of other devices found. After a few seconds the “Not Paired” status will change to “Connected” or “Paired” and the scanner blue LED will stop blinking and turn solid blue. Note: The characters in brackets are the last 6 characters of the Bluetooth Address. 5. Launch your scanner-enabled Application. The scanner will beep once indicating that it is connected to the appropriate application.
BLUETOOTH UNPAIRING Note: This procedure will put the scanner in discoverable mode. Step 1: Unpairing the scanner: Delete the Bluetooth Pairing If the scanner is paired with a device, unpair it before trying to connect to a different device. 1. Power on the scanner. 2. Press the trigger button then power button and hold both until you hear 3 beeps. The scanner will unpair and automatically power off. The next time you power on the scanner, it will be discoverable.
BLUETOOTH RECONNECTION Automatic Reconnections Each time you power on the scanner, it will automatically try to connect to the last device it was connected to. • Make sure the device is in range with Bluetooth turned on. • Pressing the trigger button will initiate the attempts to connect. • If using Application Mode, make sure the Scanner-enabled Application is launched or running. • If a connection is made, the blue light will stop blinking and turn solid.
STATUS INDICATORS Battery Charging when plugged into Power Supply Battery Status When not connected to power supply LED Activity Meaning Blinking Yellow Charging the battery Solid Green Battery is 100% full LED Activity Meaning Solid Green Battery capacity from 100% to 25% Solid Yellow Battery capacity from 25% to 10% Solid Red Warning - Battery capacity below 10% Blinking Red Charge immediately! The battery level is critically low.
STATUS INDICATORS (CONTINUED) Bluetooth Bluetooth Scan/Read Scan/Read LED Activity Meaning Quick Blinking Blue (2 blinks every second) Discoverable - waiting for a host Bluetooth connection. Slow Blinking Blue (1 blink every second) Attempting to connect to a paired device. Searching the last known Host. Note: Will STOP attempting after approx. 1 minute. No Light - No Activity Scanner has attempted to connect and failed. Press trigger button to try again.
STATUS INDICATORS (CONTINUED) Beep Pattern Sound Meaning Low-High Tone Power On High-Low Tone Power Off High-High Tone Power Supply detected and scanner started charging 1 Low Beep Scanner has toggled on-screen keyboard or keyboard toggle feature is enabled (iOS devices only) 1 Beep Scanner connected to device and is ready to scan barcodes 1 Beep Data successfully scanned 2 Beeps (same tone) Scanner disconnected 1 Long Beep Scanner gave up searching for a host 3 Beeps (escalating tone) Sc
STATUS INDICATORS (CONTINUED) Vibrate Meaning Vibrate Data successfully scanned. Command Barcodes are available on pages 43-46 to modify the LED, beep, and vibrate settings. If you are using a scanner-enabled application, typically the application provides settings for LED, beep, and vibrate settings.
PRODUCT SPECIFICATIONS Specifications D700 Dimensions (L x W x H) 5.2” x 1.5” x 1.6” (132.2 x 37.1 x 40.1 mm) Total Mass 3.
PRODUCT SPECIFICATIONS Specifications D700 Symbologies All major 1D barcodes Supported Language Settings [in Basic Mode (HID)] English, French, German, Spanish Systems/Battery Charging Requirement USB Type 5V 1A Ambient Light From 0 to 100 000 lux From pitch black to direct sun light Operating Temperature -4° to 122° F (-20° to 50° C) Storage Temperature -40° to 158° F (-40° to 70° C) Relative Humidity 95% at 140° F (60° C) (non-condensing), 4 days Sealing IP54 (Ingress Protection rating fo
HELPFUL RESOURCES Technical Support & Product Registration: https://support.socketmobile.com Phone: 800-279-1390 +1-510-933-3020 (worldwide) Warranty Checker: https://www.socketmobile.com/support/warranty-checker Socket Mobile Developer Program: Learn more at: http://www.socketmobile.com/developers The User’s Guide (full installation and usage instructions) and Command Barcodes (Advanced Scanner Configurations) can be download at: https://www.socketmobile.
SAFETY AND HANDLING INFORMATION WARNING: Failure to follow these safety instructions could result in fire or other injury or damage to the barcode scanners or other property. Carrying and Handling the DuraScan barcode scanners: The Socket Mobile barcode scanner contains sensitive components. Do not disassemble, open, crush, bend, deform, puncture, shred, microwave, incinerate, paint, or insert foreign objects into this unit. Do not attempt to disassemble the product.
BLUETOOTH DEVICE UNITED STATES FCC ID: LUBD700 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
BLUETOOTH DEVICE UNITED STATES FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
BLUETOOTH DEVICE CANADA IC ID: 2925A-D700 This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
BLUETOOTH DEVICE EUROPE CE Marking & European Union Compliance Products intended for sale within the European Union are marked with a CE Mark, which indicates compliance to applicable Directives and European Normes (EN), as follows.
BLUETOOTH DEVICE JAPAN Telec Marking Compliance R 211-161214 Products intended for sale within the country of Japan are marked with a Telec mark, which indicates compliance to applicable Radio Laws, Articles and Amendments.
BATTERY WARNING STATEMENTS This device contains a rechargeable Lithium-Ion battery. Stop charging DuraScan barcode scanners if charging isn’t completed within the normal specified time (approx. 6 hours). Stop charging the battery if the DuraScan barcode scanner case becomes abnormally hot, or shows signs of odor, discoloration, deformation, or abnormal conditions is detected during use, charge, or storage.
BATTERY WARNING STATEMENTS • Dispose of used batteries in accordance with the prevailing community regulations that apply to the disposal of batteries. • Never expose this product or the battery to any liquids. • Do not shock the battery by dropping it or throwing it. If this unit shows any type of damage, such as bulging, swelling or disfigurement, discontinue use and promptly dispose. Product Disposal Your device should not be placed in municipal waste.
LASER AND LED DEVICES Caution: DO NOT STARE DIRECTLY INTO THE LED BEAM. LED DEVICE: The DuraScan D700 and D750 contain a LED-type scan engine. For the Class 1 LED version of this engine, the following applies: • Complies with IEC 60825-1:2001-08, and EN 60825-1:1994 + A1 + A2 • LED output is in the 630-670nm range (visible red). • Class 1 LED devices are not considered to be hazardous when used for their intended purpose.
REGULATORY COMPLIANCE CE MARKING AND EUROPEAN UNION COMPLIANCE Testing for compliance to CE requirements was performed by an independent laboratory. The unit under test was found compliant with all the applicable Directives, 2004/108/EC and 2006/95/EC. WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT The WEEE directive places an obligation on all EU-based manufacturers and importers to take-back electronic products at the end of their useful life.
LIMITED WARRANTY Socket Mobile Incorporated (Socket) warrants this product against defects in material and workmanship, under normal use and service, for one (1) year from the date of purchase. Product must be purchased new from a Socket Authorized Distributor or Reseller. Used products and products purchased through non-authorized channels are not eligible for this warranty support. Warranty benefits are in addition to rights provided under local consumer laws.
COMMAND BARCODES Scan command barcode(s) to quickly configure the Scanner. Make sure the scanner is not connected to a device before scanning a command barcode! See page 22 for unpairing instructions. For a complete set of command barcodes, download the Command Barcodes Sheet: https://www.socketmobile.
COMMAND BARCODES (CONTINUED) Important! Make sure the scanner is not connected to a host computer or device before scanning a command barcode! Bluetooth Connection Modes Basic Mode (HID) (default) Configures the Scanner to Human Interface Device (HID) mode as a Keyboard class device #FNB00F40001# Application Mode (SPP) Changes the Scanner to Serial Port Profile (SPP) mode #FNB00F40000# Application Mode (MFi-SPP) Changes the Scanner to MFi mode for Apple iOS Devices #FNB00F40002# 42
COMMAND BARCODES (CONTINUED) Important! Make sure the Scanner is not connected to a host computer or device before scanning a command barcode! Beep Settings Beep after scanner Decodes Data ON (default) Enables scanner to beep to indicate successful scans. #FNB0119E00010003 0078004B# Beep after scanner Decodes Data OFF Disables scanner from beeping to indicate successful scans.
COMMAND BARCODES (CONTINUED) Vibrate Settings Vibrate ON (default) Enables scanner to vibrate to indicate successful scans. #FNB01310001000100FA0000# Vibrate OFF Disables scanner from vibrating to indicate successful scans. #FNB013100010000# Factory Default Factory Reset Revert all settings to factory defaults. The scanner will power off after scanning this barcode. #FNB00F0# For more command codes go to: https://www.socketmobile.
Extend Your Warranty... Receive Priority Service and Personal Care. You have 60 Days from purchase date to enroll in a SocketCare Service Program! For detailed information visit: https://www.socketmobile.
