Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 1 FÜR M ESSBAREN ERFOLG 3030 Operating Manual www.soehnle-professional.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 2 English Content 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Introduction . . . . . . . . . . . . . . . . . . . .Page 3 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Basic Functions . . . . . . . . . . . . . . . . . . . .Page 8 3.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Application Programs . . . . . . . . . . . . . . . . . . .Page 13 3.1 . . . . . . . . . . . . . . . . . . .
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 3 English Thank you for choosing this Soehnle Professional product. All the features of this product were designed to the state of the art and are optimised for simple and straightforward use. If you have any queries or experience any problems with the device that are not addressed in the operating instructions please contact your Soehnle Professional service partner or visit us on the Internet at www.soehnle-professional.com. 1.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 4 English 1.3 Installation and commissioning Before connecting up the appliance, make sure that the power supply complies with the specifications on the appliance's nameplate and the power plug version conforms to local regulations. Place the connected scales on a level and stable surface. Select an installation site where the appliance is protected from shocks, vibrations, intense heat or cold, draughts, chemicals and moisture.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 5 English Programming mode Here, select the required weighing application program. After selecting and activating the application program, the scale is ready to operate. Function keys ... Call specific functions by pressing function keys F1 to F6. The keys are preprogrammed to various functions depending on the program or situation. The function name appears above the key in the function bar in the display.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 6 English Input and control keys Numeric keys to type in numerical values. ... ... Multiple programming of numeric keys to type in alphabetic characters Calls organisation data Clears complete input Clears last number Info key, electronic nameplate with calibration data.
Ba_3030_GB_neu.qxd 04.12.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 8 English 2. Basic functions The basic functions are similar or identical for all application programs. 2.1 Power on/off Power-on After power-on and during the run-up phase, the Soehnle Professional logo is displayed. The measuring points are briefly listed as they are detected. The scale is zeroed after the power-on routine (this may differ with non calibratable calibration). After power-on, the last application program activated is reopened.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 9 English 2.3 Zeroing Press the zeroing key to correct minor deviations from zero, e.g. caused by soiling on the scale. Zero range calibratable and non calibratable: -1 to +3% of the weighing range. If zeroing is not possible, the error message "Above zero range limit" or "Below zero range limit" appears for two seconds in the display. Zero tracking Zero tracking automatically corrects minor deviations in the zero display. 2.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 10 English 2.6 Organisation data (identifiers) Organisation data help to assign identifiers to document weighing operations, e.g. article number, supplier, machine operator. They are available in all application programs. The 3030 Programming Terminal has 4 organisation data memories. Each memory has: - one user-definable description, e.g. "Article no." (up to 12 characters) - one user-definable content, e.g.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 11 English Printout: Press the "Org A", "Org B", "Org C" and "Org D" keys together with F6 Accept to print out (only possible if a print view is saved). Only the organisation data contained in an entry are printed out. Show content: Press the associated ORG key. Clear content: Press the associated ORG key. Press the CL key followed by F6 Accept. Info: When a barcode function is used, the organisation data display is disabled. 2.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 12 English 2.9 Alphanumeric input Use the combined numerical/alphanumeric keypad to type in numerical and alphanumeric inputs (similar to a mobile phone keypad). Types of input box - Display boxes with no type-in option - Display/type-in boxes with numerical input option - Display/type-in boxes with alphanumeric input option Activating input boxes - Situation-dependent by means of function keys or direct numerical input. The Input view appears in the display.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 13 English 3.0 Application programs The various application programs on the Soehnle 3030 Programming Terminal offer you a wide range of solutions for weighing operations. You can adapt the application programs to your specific needs in Setting mode. For information on this, please refer to the subject of Setting mode in the detailed CD manual. Below is a list of the application programs available to you: 1. . . . . . . . . . . . . . .Weighing and taring 2. . .
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 14 English 3.1. Weighing and taring Basic functions: Weighing and measuring gross and net weights. Warning: This description applies to the options Autotare and Totalising tare in the factory setting. When you activate these options in Setting mode, it affects the procedures described. 3.1.1 Function keys The F1 to F6 function keys help you control the functions. They are programmed in 2 levels.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 15 English 3.1.3. Weighing without taring Place weighing product on the scale. The weight is indicated with the message "Gross". 3.1.4 Manual taring Measure and tare with a container of unknown weight. Place the empty container on the scale. Press the Tare key. The tare value is saved. The weight display is zeroed. The weight is displayed with the message "Net". When the scale is clipped off, the tare weight is displayed with a negative sign.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 16 English 3.1.6 Multiplicative tare Tare several containers of the same weight. See the description of the function in the CD manual. 3.1.7 Additive tare Tare several, even different containers of known weight. See the description of the function in the CD manual. 3.1.8 Provisional tare Unknown tare weights are added to the existing tare memory. See the description of the function in the CD manual. 3.1.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 17 English Saving the new fixed value Press F1 New. The memory location number is assigned by the appliance. The first figure in brackets indicates the number of free memory locations; the second figure shows the memory locations occupied by fixed tare values. The Description parameter is marked. Call by pressing F6 Edit. Type the value into the numerical/alphanumeric keypad. Accept the input by pressing F6.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 18 English 3.2 Totalising and batching Totalising means that the individual pieces are weighed one after the other. The weight is added in the total memory and the scale is clipped off after each weighing operation. Batching means that the weighed pieces remain on the scale. The weight is added in the total memory and the scale is zeroed without being clipped off. A change in measuring point during batching is not possible.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 19 English 3.2.2 Display view After the first totalising function, the display changes from basic view to the total view. 3.2.3 Taring Taring functions same as for 3.1 Weighing and taring. 3.2.4 Operating the totalising functions Call the totalising functions level by pressing the function change key. F6 Plus: Press the Plus key to transfer the weight on the weighing platform to the total memory.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 20 English F4 Cancel Press the Cancel key to cancel or reweigh individual pieces. After pressing the Cancel key, you are requested to load the scale either with the weight you want to cancel or to type in the consecutive number of the weight you want to cancel. For information about the consecutive number, press the key combination Info and F5 Plus.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 21 English 3.2.9 Piece counter The piece counter only counts operations that are actually totalised. With every new operation that uses Plus, Manual or Automatic Totalising, the piece counter is incremented by 1. The piece counter runs up to 999; then an error message appears. When a cancellation is made, the piece counter is decremented by 1. The piece counter is automatically zeroed when the total is cleared. 3.2.
Ba_3030_GB_neu.qxd 04.12.2006 11:01 Seite 22 English 3.2.12 Displaying individual pieces During a totalising operation, you can call individual pieces from the total memory by pressing the Info key then the F5 Plus key immediately after. The piece list starts with the most recent entry. Browse through the list by pressing the arrow keys F3 (older entries) or F4 (more recent entries). You can call the last 50 entries. Press F5 Back to exit the display of individual pieces and return to the previous view.
Ba_3030_GB_neu.qxd 04.12.2006 11:02 Seite 23 English 3.3 Counting Count parts with the same weight. The individual part weight (reference weight) is calculated from a small known quantity of countable parts. The reference weight is then used as the divisor to calculate the quantity of countable parts from the weight of an unknown quantity. 3.3.1 Function keys The F1 to F6 function keys help you control the functions. They are programmed in 4 levels.
Ba_3030_GB_neu.qxd 04.12.2006 11:02 Seite 24 English 3.3.2 Counting display view Tip: Activate and deactivate the additional display showing the weight info by pressing F3 Unit in the Setting Functions level. 3.3.3 Taring Taring functions same as for 3.1 Weighing and taring. 3.3.4 Counting function The reference weight is measured by using the following keys in Level 1 Counting Functions: Function key F1 Ref 10 Calculate the reference weight from a default reference quantity.
Ba_3030_GB_neu.qxd 04.12.2006 11:02 Seite 25 English New reference weight Previous reference weights are overwritten with the new reference weight calculated. Displaying the reference weight Press F3 Ref Wght in Level 1 Counting Functions. Weight display during count operation Press F3 Unit in Level 4 Setting Functions to activate the weight display at the top left of the display.
Ba_3030_GB_neu.qxd 04.12.2006 11:02 Seite 26 English Saving the new fixed value Press F1 New. The memory location number is assigned by the appliance. The first figure in brackets indicates the number of free memory locations; the second figure shows the memory locations occupied by fixed tare values. The Description parameter is marked. Call it by pressing F6 Edit. Type in the value using the numerical/alphanumeric keypad. Accept the input by pressing F6.
Ba_3030_GB_neu.qxd 04.12.2006 11:02 Seite 27 English Switch between part and percent by pressing the function change key F>. If you wish to define the plus and minus tolerances separately, activate the "+/- tolerance separate" function in Setting mode. The display switches to the Count display view. The special characters are activated. The relevant special character is displayed next to the setpoint depending on the actual weight on the scale.
Ba_3030_GB_neu.qxd 04.12.2006 11:02 Seite 28 English 3.3.7 Counting with several weighing platforms If several scales are connected, the reference weight can be measured and counted on each scale. For best results, we advise you to measure the reference weight on the scale with the finest resolution. Select a scale by pressing the Scale key.
Ba_3030_GB_neu.qxd 04.12.2006 11:02 Seite 29 English 3.4 Checking Check whether the weighing product corresponds to a setpoint weight within a default tolerance band. Example: Several weighing products must be checked for compliance with the setpoint weight. This function can also be used for weighing in a default setpoint. Example: 50 kg must be filled in a container at a max. tolerance of 3%.
Ba_3030_GB_neu.qxd 04.12.2006 11:02 Seite 30 English 3.4.2 Check display view Tip: An additional way to display the deviation from the setpoint on the calibrated unit is to activate the additional display by pressing F3 Unit in the Setting Functions level. 3.4.3 Taring Taring functions same as for 3.1 Weighing and taring. 3.4.4 Checking functions Type in setpoints. Press F1 Setpoint in Level 1 Checking Functions.
Ba_3030_GB_neu.qxd 04.12.2006 11:02 Seite 31 English You can also display the difference between actual values and setpoint weights at the top left of the additional display in figures with a + or - sign. Activate the additional display by pressing F3 Unit in the Setting Functions level. If you activated a memory location containing setpoints and tolerances in the Fixed Check memory, the special characters are activated automatically.
Ba_3030_GB_neu.qxd 04.12.2006 11:02 Seite 32 English Saving the new fixed value Press F1 New. The memory location number is assigned by the appliance. The first figure in brackets indicates the number of free memory locations; the second figure shows the memory locations occupied by fixed tare values. The Description parameter is marked. Call by pressing F6 Edit. Type in the value using the numerical/alphanumeric keypad.
Ba_3030_GB_neu.qxd 04.12.2006 11:02 Seite 33 English 4. Further information You will find further information on the following subjects in the detailed documentation, the 3030 Programming Terminal manual, on the supplied CD: - Application programs 5 to 10 - Setting mode - Error messages - Print - Barcode - etc.
Ba_3030_GB_neu.qxd English 34 04.12.
Ba_3030_GB_neu.qxd 04.12.
Ba_3030_GB_neu.qxd 04.12.2006 11:02 Seite 36 Wilhelm-Soehnle-Straße 2 71540 Murrhardt Telephone +49 (0) 71 91 / 34 53-0 Telefax +49+49 71 /9193/ 19-220 34 53-211 Telefon (0) (0) 71 92 info@soehnle-professional.com Telefax +49 (0) 71 92 / 93 19-211 E-Mail info@soehnle-professional.de www.soehnle-professional.com 470.051.068 470.051.068GB GB Soehnle Professional GmbH & Co. KG Manfred-von-Ardenne-Allee 12 Soehnle Professional DE-71522 Backnang GmbH & Co.