5 Piece Wicker Sofa Set
PART LIST A (armless chair) (armless & corner chair) Seat Panel 1 PC (ottoman) Back Panel 2 PCS Wicker Top 1 PC (coffee table) Long Side Panel Short Side Panel 2 PCS 2 PCS V (ottoman) (corner chair) (corner chair) Seat Panel 2 PCS Arm Panel 2 PCS J (ottoman) (coffee table) Long Side Panel Short Side Panel 2 PCS 2 PCS (coffee table) Glass Top 1 PC (ottoman) Pillow 2 PCS 2 Wicker Top 1 PC U T W Seat Cushion 1 PC E I S L (coffee table) Back Panel 1 PC H (corner chair) K (armle
HARDWARE LIST M N O M6*30mm M6*50mm Bolt 40 PCS Long Bolt 28 PCS P M6mm Flat Washer 96 PCS Q M6mm M6mm Hex Nut 28 PCS Allen Wrench 2 PCS R M6mm Wrench 2 PCS EXTRA HARDWARE LIST M N M6*30mm Bolt 4 PCS O M6*50mm Long Bolt 3 PCS P M6mm Flat Washer 6 PC 3 M6mm Hex Nut 3 PCS
Step 1. Lay seat panel (part A) upside down on a soft flat surface, such as carpet, as shown below. Attach side panels (part B) to seat panel (part A) using bolts (part M), flat washers (part O) and allen wrench (part Q). NOTE: Please do not fully tighten bolts until unit is fully assembled. M x6 O x6 Q x1 Step 2. Attach back panel (part C) to seat panel (part A) and side panels (part B) using long bolts (part N), flat washers (part O), hex nuts (part P), allen wrench (part Q) and wrench (part R).
Step 3. Carefully turn the assembled unit upright. Add seat cushion (part T) and back cushion (part U) as shown below.
Step 4. Lay seat panel (part D) upside down on a soft flat surface, such as carpet, as shown below. Attach side panel (part B) to seat panel (part D) using bolts (part M), flat washers (part O) and allen wrench (part Q). NOTE: Please do not fully tighten bolts until unit is fully assembled. M x3 O x3 Q x1 Step 5. Attach back panel (part F) to arm panel (part E) using long bolts (part N), flat washers (part O), hex nuts (part P), allen wrench (part Q) and wrench (part R).
Step 6. Attach assembled unit (parts B & D) to arm panel (part E) and back panel (part F) using long bolts (part N), flat washers (part O), hex nuts (part P), allen wrench (part Q) and wrench (part R). NOTE: Please fully tighten all bolts at this time. N x8 O x16 P x8 Q x1 R x1 Step 7. Carefully turn the assembled unit upright. Add seat cushion (part T) and back cushion (part U) as shown below. Repeat steps 4-7 to assemble remaining corner chair.
Step 8. Lay wicker top (part G) upside down on a soft flat surface, such as carpet, as shown below. Attach long side panels (part H) to wicker top (part G) using bolts (part M), flat washers (part O) and allen wrench (part Q). NOTE: Please do not fully tighten bolts until unit is fully assembled. M x4 O x4 Q x1 Step 9. Attach short side panels (part I) to wicker top (part G) and long side panels (part H) using bolts (part M), flat washers (part O) and allen wrench (part Q).
Step 10. Carefully turn the assembled unit upright. Add seat cushion (part V) as shown below.
Step 11. Lay wicker top (part J) upside down on a soft flat surface, such as carpet, as shown below. Attach long side panels (part K) to wicker top (part J) using bolts (part M), flat washers (part O) and allen wrench (part Q). NOTE: Please do not fully tighten bolts until unit is fully assembled. M x4 O x4 Q x1 Step 12. Attach short side panels (part L) to wicker top (part J) and long side panels (part K) using bolts (part M), flat washers (part O) and allen wrench (part Q).
Step 13. Carefully turn the unit upright. Place glass top (part S) on wicker top (part J). Step 14. Add pillows (part W) as shown below.