LYNK Edge Card Manual for Sol-Ark

ManualsBrandsSol-Ark ManualsSolar & Wind PowerPower Kit with 13,320 watt of PV and 22.5kWh of Discover AES LiFePO4 Battery Storage

1. Safety 2

1.1 Warnings, Cautions and Notes 2

1.2 General Warnings 2

2. Documentation 3

3. Overview 4

3.1 System Overview 4

3.2 Minimum Battery Capacity 4

PN: 950-0016-SLRK

LYNK Edge Card Sol-Ark

User Manual

#4 -13511 Crestwood Place, Richmond, BC, V6V 2E9, Canada + 1.778.776.3288 info@discoverbattery.com

discoverbattery.com

805-0029 REV A

4. Installing and Connecting LYNK to the Sol-Ark Network 5

4.1 Installing the LYNK Edge Card 5

4.2 Connecting LYNK to the Sol-Ark Network 6

6. System Set Up 7

Summary of content (7 pages)

PAGE 1
LYNK Edge Card Sol-Ark User Manual PN: 950-0016-SLRK 1. Safety 2 4. Installing and Connecting LYNK to the Sol-Ark Network 5 1.1 Warnings, Cautions and Notes 2 4.1 Installing the LYNK Edge Card 5 1.2 General Warnings 2 4.2 Connecting LYNK to the Sol-Ark Network 6 2. Documentation 3 3. Overview 4 3.1 System Overview 4 3.2 Minimum Battery Capacity 4 6. System Set Up 7 805-0029 REV A #4 -13511 Crestwood Place, Richmond, BC, V6V 2E9, Canada + 1.778.776.3288 info@discoverbattery.
PAGE 2
1. Safety 1.1 Warnings, Cautions and Notes ▲ WARNING Death or Injury ▲ CAUTION Equipment Damage ▲ NOTE Additional Information 1.2 General Warnings ▲ WARNING HAZARD OF ELECTRICAL SHOCK AND FIRE • • Connect LYNK to only Safety Extra Low Voltage (SELV) circuits and power sources. All wiring must be completed by qualified personnel to ensure compliance with applicable installation codes and regulations. Failure to follow these instructions can result in death or serious injury.
PAGE 3
2. Documentation This User Manual provides information about the integration of Discover AES Lithium batteries with Sol-Ark devices in a closed-loop configuration using the AES LYNK Communication Gateway with installed AES LYNK Edge Card for Sol-Ark. AES battery can be use in Energy Storage System (ESS) for self consumption, grid backup and off-grid applications. These instructions apply to an off-grid application.
PAGE 4
3. Overview 3.1 System Overview The AES LYNK Communication Gateway unlocks the full potential of a Discover AES LiFePO4 battery by enabling the internal Battery Management System (BMS) to optimize the charge and discharge configurations of the world’s best inverter/ chargers and solar charge controller systems in a closed loop configuration. AES LiFePO4 batteries must be set up to work with power conversion and monitoring devices in either an open-loop or closed loop configuration.
PAGE 5
4. Installing and Connecting LYNK to the Sol-Ark Network 4.1 Installing the LYNK Edge Card The LYNK Edge Card for Sol-Ark is a Slot 0 Type which only inserts into the left side slot on the bottom of the LYNK Communication Gateway. ▲ NOTE • • • The LYNK Edge Card type to be used is determine by the brand of power conversion equipment. If LYNK Edge Card is in the wrong slot, it will not function. If LYNK Edge Card is not firmly seated, it will not function.
PAGE 6
4.2 Connecting LYNK to the Sol-Ark Network Before connecting LYNK to the Sol-Ark Network ensure that the firmware for all Sol-Ark devices is up to date.
PAGE 7
5. System Setup Turn on the inverter and navigate to the “BATT” tab in the Basic Setup Menu and ensure that BMS Lithium Battery is enabled with a check mark and displays 00**. 00 00 ** Refer to the most recently published Sol-Ark manual to verify BMS Lithium Battery number remains 00. 7 discoverbattery.