GREEN ENERGY
CONTENTS Tools You May Need P.1 Mechanical Parts List P.1 Plastic Parts P.3 Mechanical Assembly P.4 How It Works P.17 How To Play P.21 Trouble Shooting P.
The Salt Water Fuel Cell Motorcycle is equipped with cams and swing arms, the multiple variations allows for full throttle excitement: powerful Straight runs, Right or Left circling, and radical “S” turns. Children will be awed by the remarkable simplicity and effectiveness of the toy. After activating the fuel cell module with a saltwater mixture, the magnesium metal sheet can operate the motorcycle for about 3 hours continuously. Environmentally safe, non-toxic, and clean.
P4 Gear(Blue) P5 Gear(Orange) QTY QTY 1 3 5 P8 Gear With Shaft QTY QTY 1 1 P10 Nonwoven Fabric Green P9 Air Cathode(Black) QTY QTY QTY 1 1 2 P11 Magnesium Sheet Plastic Dropper sheet P12 Magnesium QTY QTY 2 1 QTY 2 (Spare parts:4pcs) Sponge P13 Round Shaft QTY Hex Shaft P7 Magnesium Sheet (Spare parts:2pcs) P6 Sticker P14 (Spare parts) QTY QTY 1 P2 1
Plastic Parts Cut the plastic parts when they are required . Do not cut them in advance. Hints burr burr Cut off the burrs before assembly.
Mechanical Assembly 01 A8 A9 P13X12 1 2 02 B5 1 B4 2 P13X12 P4
03 C5 1 P9 (Air Cathode) 2 P10 (Nonwoven Fabric) 3 C4 Black Side Up P11 (Magnesium Sheet) 4 5 6 x2 Make sure the P9,P10,P11 placed in correct sequence and position. 04 A10 05 A7 A5 A4 C7 C7 09 Decorating & Labelling as per the right and left figure. 13 06 P6 C2 P6 Push the P6 to the bottom as above figure.
07 A6 06 A3 Top View A3 18 19 07 B10 12 11 14 Refer to the figure on the right for help with sticker placement.
08 07 B6 01 09 10 08 Refer to the figure on the left for help with sticker placement.
C6 B2 P6X2 Don't pull off the wires ! P1 P3 P8
Side View 1 2 P8(Green) P5(Orange) 3 4 P5(Orange)X2 B7 P4(Blue) 5 P9
A1 08 Turn 90° B8 P10
1 Cut off the burrs of C3 before assembly.
A14 (or A11) 14 Ensure the connectors are fully inserted at a 90° angle. Any other angle is incorrect. A11 (or A14) P2 Yellow 90° Black Red Ensure the connectors are fully inserted. 15 A13 C8 16 Make sure the parts below placed in correct sequence and position.
Routing the wires as below.
19 17 16 Decorating & Labelling as per the left figure.
Left Side Assembly 20 04 Side View 21 Right Side Assembly 05 Side View P15
22 B3 (Stand B3 for parking your motorcycle purpose.
How It Works After a period of time the salt water will be exhausted ( about 20 minutes ), the motorcycle will begin to get slower or stop. Add a few more drops of salt water to start it again ( as in fig 3 ). Each Magnesium sheet can work for 3 hours continuously, then it will become fragmented. Replace the sheet with a new one to energize the motorcycle. The kit includes 4 refills. All materials used in this kit are environmentally safe and clean, no toxic substances or disposal concerns.
d. Magnesium Sheet e. f. Cover Reassemble cover and magnesium sheet Make sure the polarity of the connector dry without salt water Insert Fuel Cell plate g. Run your motorcycle now 3 How to refill the salt water : When the motorcycle starts getting slower or stops, reapply a few drops of salt water with the applicator into the position as shown 2 C. And scratch oxide from the battery connectors and also magnesium sheet by slotted screwdriver before reuse. See below figures: a.
Take off the motorcyclist as below steps b-1. b-3. b-2. c. Scratch Here d.
5 How to maintain Fuel Cell plate : It is necessary to clean Fuel Cell plate every time when not in use. 5-1 Gently rinse air cathode under tap water, don’t hand rub the surface to ensure the quality of air cathode. Air Cathode Air Cathode 5-2 Flush the parts shown below and hand rub the surface. Make sure that there is no salt residue. Dry all parts separately. 1.Nonwoven Fabric 2.
How To Play Straight Run Right Side Assembly 05 Side View Left Side Assembly 04 Side View P21
Left Circling Left View Left circling Right View Right Circling Right View Ri ght c ircling Left View P22
“ S ” Turn Rotating the rear wheel by finger until marking “ on the both sides accordingly.
Left Side Assembly 05 P24
Check the steps below if your Motorcycle doesn’t move after adding salt water. 1 Make sure motor and gears are installed in right position. 2 Make sure each connector must be set in right position (Ref: 14 ) 3 Make sure cut off the burrs of C3 before assembly.(Ref: 13 ) 4 Make sure Fuel Cell plate is inserted entirely. (Ref: 17 ) 5 Replace a new magnesium sheet if it is eroded as shown below.
Copyright © 2014 CIC.
