User Manual

ManualsBrandsSolarEdge ManualsEV ChargersSolarEdge SE7600H HD-Wave w/ EV Charger Inverter

EV Charger Cable Installation and EV Charger Configuration

Contents

EV Charger Cable Installation and EV Charger Configuration 1

Introduction 1

Mounting the EVCharger Cable 1

EV Charger Activation and Configuration 3

EV Charger Configuration and Monitoring 4

Specifications 5

Charging Instructions 6

Version History

Version 1.2 , December 2018 - Added caution about cable holder mounting position

Version 1.1, Apr 2018 - Clearance updated; addition of operating instructions

Version 1.0 , Feb 2018 - Initial release

Introduction

The EV Charger Cable is used with SolarEdge‘s EVCharging Single Phase Inverter (referred to as inverter). This document

describes how to install and connect the cable and how to configure the EV Charger.

Package Contents

A holder that is mounted on a wall/ pole (screws are not included)

EVCharger Cable

Cable lock

Required Equipment

4 screws

Screwdriver

Drill

NOTE

Connection to the SolarEdge monitoring platform is required for first EV charging. Use ZigBee or Ethernet connection.

You can also use cellular connection, which requires a SIM card with a 50 MB data plan that should be purchased from a

cellular provider; a SolarEdge data plan supports activation only.

Mounting the EVCharger Cable

Install the EVCharger Cable after the inverter is already installed (refer to the Inverter Installation Guide).

1. Connect the EV charger Cable to the inverter (see

Figure 1

1. Align the two white arrows on the EV charger cable connector with the white dot on the inverter

connector located at the bottom of the inverter: the dot should be between two arrows.

2. Plug the connector into the EV connector.

3. Rotate the cable connector clockwise to fasten it.

EV Charger Cable Installation and EV Charger Configuration MAN-01-00455-1.2

Summary of content (6 pages)

PAGE 1
EV Charger Cable Installation and EV Charger Configuration Contents EV Charger Cable Installation and EV Charger Configuration Introduction Mounting the EV Charger Cable EV Charger Activation and Configuration EV Charger Configuration and Monitoring Specifications Charging Instructions Version History 1 1 1 3 4 5 6 Version 1.2 , December 2018 - Added caution about cable holder mounting position Version 1.1, Apr 2018 - Clearance updated; addition of operating instructions Version 1.
PAGE 2
Mounting the EV Charger Cable Figure 1: EV cable connection 2. Determine the mounting location, on a wall, stud framing or pole. Maintain the following minimum clearance areas between the holder and other objects: 8" (20 cm) from the top and sides of the holder 24" (60 cm) - 4 ft (1.2 m) from the bottom of the holder CAUTION! Install the cable holder (storage means) between 24-48" (60-120cm) from ground (grade).
PAGE 3
EV Charger Cable Installation and EV Charger Configuration 8. Activate and configure the EV Charger as described in the next section. NOTE Keep the dust-cap closed when the charger is not in use. EV Charger Activation and Configuration After installing the EV Charging Single Phase Inverter, and the EV Charger Cable, the EV Charger should be activated in order to enable charging.
PAGE 4
EV Charger Configuration and Monitoring Figure 5: EV Charger activation 5. When the EV Charger is activated and ready for configuration, the following screen is displayed. Tap OK. Figure 6: EV Charger activated EV Charger Configuration and Monitoring 1. Before starting, make sure that: The inverter is installed and activated (refer to the Inverter Installation Guide) The EV Charger Cable is installed The EV Charger activation is complete 2. Access the SolarEdge monitoring app. 3.
PAGE 5
EV Charger Cable Installation and EV Charger Configuration Specifications EV Charger Connector Charging Cable Length Charging Cable Weight Holder Weight IEC62196 Type 1 / Type 2 25 ft. 7.6 m (15 ft 4.6 m option) 12.5 lb.5.7 kg (7.7 lb. 3.5 kg for the 15 ft. 4.6 m option) 0.6 lb. 300 gr EV Charger Cable Installation and EV Charger Configuration MAN-01-00455-1.
PAGE 6
Charging Instructions Charging Instructions 1. Verify that the green LED at the bottom of the inverter is ON indicating that the EV Charger is ON and ready to charge. 2. Hold the EV Charger plug and unwind the cable from the holder. 3. Connect the EV Charger plug to the charging socket of the vehicle and push firmly until it clicks into the socket. The inverter will sound 1 short beep and the blue LED will turn on (the green LED turns off) to indicate a proper connection.