Models SG-TTW-09ESE-26 SG-TTW-12ESEZ-26 SG-TTW-09HC-26 SG-TTW-12HC-26 Electronic Through the Wall Air Conditioner Operating Instructions
Contents IMPORTANT NOTE TO THE OWNER ........................... 1 IMPORTANT NOTE TO THE SERVICER ....................... 1 Unit Features ................................................................ 1 Transportation Damage .............................................. 1 Unpacking The Unit ..................................................... 1 Operating Instructions ................................................. 1 Installation Instructions .............................................. .
Specifications • • • Noise level is measured at a distance of 3.28ft away from the front of the unit in cooling mode. Power consumption is measured when the fan runs at the highest speed settings. These specifications are for reference only. For actual data, please refer to the rating label on the unit.
Operating Instructions IMPORTANT NOTE TO THE OWNER This equipment is to be serviced by professionally trained personnel only. If this equipment is improperly installed, adjusted or altered by an unqualified person, a safety hazard may result. IMPORTANT NOTE TO THE SERVICER Read this manual and familiarize yourself with the specific items which must be adhered to before attempting to service this unit.
CHASSIS INSTALLATION 1. Remove front grille. See Figure A. WARNING To prevent electrical shock, property damage, personal injury, or death, do not remove grounding prong from plug. Follow all operating instructions.
Locking Plate Figure 3 3. Remove shipping pads inside air conditioner next to compressor. (See Figure B.) Figure C 6. If outlet is on the left side of the unit. route power cord as shown in Figure D. Remove shipping pads Clamp Figure B 4. Carefully slide the chassis into the sleeve. Ensure that the ground wire is not pinched or in the path of the condenser fan. 5. Loosen locking plate screw and rotate tab with tab behind wall case flange (See Figure C) then tighten locking plate screw.
To replace front grille: Grille Tab EXHAUST AIR VENT Figure 4 AIR DIRECTION: Horizontal louvers on the front grille let you control the air direction up and down. Hook the tabs on the front grille even with the tabs on the case and snap into place. Replace the screws and filter. Refer to Page 4, Figure A. VENT CONTROL AND AIR DIRECTION (See Figure E) The vent control is located behind the front grille on the right side of the air discharge area.
Remove the front grille to adjust the vertical louvers side-toside to direct the air left or right. Wiring Before wiring the unit, please review the following warnings and cautions. WARNING To avoid the risk of electrical shock, personal injury or death, do not service this unit without first opening all disconnects and/or removing the unit cord set plug from the wall outlet. WARNING To avoid the risk of electrical shock, personal injury, or property damage, do not use an extension cord with this unit.
Air Conditioner Features ELECTRONIC CONTROL OPERATING INSTRUCTIONS Before you begin, thoroughly familiarize yourself with the control panel and remote as shown below and all its functions. Then follow the symbol for the functions you desire. The unit can be controlled by the touch pad alone or with the remote.
OPERATING THE REMOTE CONTROL NOTE: Make sure there are no obstructions between the receiver on the A/C and the remote control. Do not drop or throw the remote control. Do not allow water to get inside the remote control and do not place the remote control in direct sunlight or a place where it is very hot. • Press the SLEEP button to turn SLEEP mode on or off. SLEEP mode is set to off automatically. When SLEEP mode is selected the timer can be adjusted. SLEEP mode is not available in Fan or Auto mode.
OPERATING THE REMOTE CONTROL • Press the TIMER button when the unit is off to set up the Auto-on timer. The Auto-on time can be set between .5 24 hours. The icons “T-ON” and “H” will flash for 5 seconds. Start selecting the time using the “+” and “-” buttons before the icons stop flashing. The time will increase/decrease in .5 hour increments with each press of the “+” or “-” buttons. To cancel the Auto-on time, manually press the ON/ OFF button to turn the unit on.
Air Conditioner Features Guide for operation- General operation 1. To power on the unit, press the ON/OFF button. The unit will start to run. (Note: When it is powered off, the louvers will close automatically.) 2. Press MODE button, select desired running mode, or press COOL or HEAT mode to enter into the corresponding operation directly. 3. Press the + or - button to set the desired temperature. (It is unnecessary to set the temp. in AUTO mode.) 4. Press the FAN button to set fan speed.
Air Conditioner Features (continued) YOU WILL SEE: TO TURN UNIT ON: DO THIS: PRESS ON/OFF BUTTON TO CHANGE TEMPERATURE SETTING: YOU WILL SEE: DO THIS: PRESS TO RAISE PRESS TO LOWER Note: Tap or hold either up(^) or down(v) button until the desired temperature is seen on display. This temperature will be automatically maintained anywhere between 61F (16° C) and 86F (30° C) for both cooling and heating modes. If you want the display to read the actual room temperature, select the Fan Only mode.
Air Conditioner Features (continued) TO OPERATE ON FAN ONLY: LIGHT ON YOU WILL SEE : DO THIS: PRESS MODE BUTTON CHOOSE FAN ONLY Note: Use this function only when cooling is not desired but room air circulation is needed. You can choose any fan speed you prefer, EXCEPT AUTO FAN. During this function, the display will show the current room temperature, not the set temperature.
Air Conditioner Features (continued) YOU WILL SEE: HEATING FEATURE (on some models) : DO THIS: PRESS MODE BUTTON SELECT HEAT Note: This feature can be used with any combination of FAN Speeds, Timer, or Sleep Modes. When in the “Heat” Mode, the fan will run continuously while heat is needed. The temperature will automatically be maintained anywhere between 61°F (16°C) and 86°F (30°C). When the set room temperature is reached, the fan will cycle off and on to circulate and sample the room air.
ADDITIONAL THINGS YOU SHOULD KNOW Now that you have mastered the operating procedure, here are more features in your control that you should know. � � � � The Remote Control will operate all the control panel features, follow the same instructions. ! The "Cool "circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly. This prevents overheating of the compressor and possible circuit breaker tripping. The fan will continue to run during this time.
WARRANTY One Year Limited Warranty Soleus International, Inc. warrants the accompanying Soleus Air Powered by Gree Air Conditioner to be free of defects in material and workmanship for the applications specified in its operation instruction for a period of ONE (1) year from the date of original retail purchase in the United States.