GPS Tour GPS Tour User Manual Introduction Thank you for purchasing the GPS Tour Watch. This GPS Watch is packed with personal Training features like speed, trip time, laps, etc. Watch features include but not limited to the following: Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø 12/24H Time format Chronograph World time Dual Time T1 and T2 5 daily Alarms RUN mode Chronograph mode Timer mode HRM mode (2.
GPS Tour Step 2) Charging the Battery: Step 3) Configure your Watch: Charge the unit for at least 4 to 5 hours before first use. The length of time for a fully charged battery will last depending on the actual usage. It is recommended to regularly re-charge your battery every 1-2 months even if it is not used to maintain good battery condition. Before using your watch, you may please set your Watch. 2.1) Plug your USB PC link cable to your PC 2.
GPS Tour How to set the TIME: TIME 1/ Time 2 setting: • Press S5 while TIME is blinking. The watch will display T1 or T2. • Press S1/S11 to choose between T1 or T2 to set. • Press S5 to set the selected time (T1 or T2). The watch will display GPS or MANUAL. • Press S1/S11 to select GPS or MANUAL. You have two options in setting the watch, GPS or MANUAL. In manual setting, you can manually set the time.
GPS Tour How to set the HRM: Press S5 while HRM is blinking. ZONE 1 will start to blink. Press S1/S11 to change the zone. There are 3 preset zones Press S5 and the watch will display the LOWER limits of the selected zone. LOW limit digit will start to blink. Press S1/S11 to change the low limit value. Press S5 to confirm. High limit digit will start to blink. Press S1/S11 to change the high limit value. Press S5 to confirm. The watch will display ZONE ALERT ON or OFF.
GPS Tour How to set the NIGHT mode function: • • • • • • • • • • • • Press S5 while NIGHT is blinking. The watch will display 10 seconds blinking. Press S1/S5 to change to 20 sec or NIGHT ON. While on 10 SEC or 20 SEC setting, Press S5 to accept the setting and go back to NIGHT setting screen. While on NIGHT ON setting screen Press S5 to accept the ON setting. The watch will display the START TIME. Press S1/S11 to toggle between START TIME and END TIME. Press S5 or 3 seconds auto to set the START TIME.
GPS Tour How to set the TIMER: • • • • • • • • • Press S5 while TIMER is blinking. The segment number will start to blink. Press S1/S11 to change the segment number Press S5 to set the HOUR. The hour digit starts to blink. Press S1/S11 to change the digits Press S5 to set the MINUTE. The minute digit starts to blink. Press S1/S11 to change the digits Press S5 to set the SECONDS. The second digit starts to blink. Press S1/S11 to zero the digits.
GPS Tour 3.4) TIMER can also be set in TIMER SET mode • • Press and hold S11 until SG 1 (segment 1) blinks. Press S5 to set the hour, minute and second. 3.6) ALARM can also be set in ALARM quick SET mode. • Press and hold S11 until the “ALARM” blinks. • Press S5 to set the alarm 1 to 5, hour, minute, T1/T2 and Alarm On/Off. 3.5) HRM and LINK HRM can also be set in HRM quick SET mode. • Press and hold S11 until HRM LINK blinks. • Press S5 to enter HRM link. It will then start to search (within 1 min.
GPS Tour Step 4) Acquire Satellite signals: In order to get the correct time of day and begin using your watch, you have to acquire the Satellite signals. It may take a few minutes to get the signals. 4.1) Go outside to an open area away from tall buildings and trees. Orient the GPS antenna towards the sky for best reception. The antenna is located at the 12 o’clock position of the watch. 4.2) Stand still and do not begin moving while locating the Satellites until the GPS signals are already received. 4.
GPS Tour GPS signals and its meaning: You will hear a beep sound when the Watch has received a GPS signal or when the GPS signal has been lost. LOST GPS signal will also be displayed in the screen. Step 5) Pair your Heart Rate monitor: The HRM belt is on standby and ready to send data to your Watch. Wear the belt directly on your skin just below your breastplate. It should be snug enough to stay in place during your run. 5.4. Link your HRM belt to the Watch.
GPS Tour • • • 5.5. If the heart rate data does not appear on the Watch, or if you have erratic data, follow the tips below. If the problem persists, you may have to pair the HR belt again. • • • • • Make sure the HR belt is snugly fit to your body. Reapply water or electrode gel to the electrode of the HR belt. Clean the electrodes from possible contamination that may interfere with heart rate signals. Wear a cotton shirt or if possible, wet your cotton shirt.
GPS Tour Step 6) Go for a RUN: 6.1) Using RUN mode 6.1.1. How to enter RUN mode: • Press S1 or S7 from Time mode to go to RUN mode. The watch will prompt you to GPS GO (if Satellite signal already received) or INDOOR (if no signal received). • Press S1 to start or re-start. • Press S5 to take LAP. If auto lap function is set, the watch will take lap automatically based on auto lap setting and there is a beep sound during taking of auto lap. • Press S1 to stop after completing your run.
GPS Tour 6.1.3. How to change views: Press S5 to change the information displayed in Line 2 if you have selected a 3-ROW display in SET mode/VIEW. If you have selected a 2-ROW display, Line 1 information will be changed as you press S5. Following are the information displayed as you press S5: 2-ROW display: Line 1 information will change as you press S5. Information displayed in Line 2 can be set in SET mode/ VIEW. 3-ROW display: Line 2 information will change as you press S5.
GPS Tour 6.1.4. How to view your current data before saving while the chronograph is stopped. Following are the information as you press S5: Notes: o o o o Before going for a run exercise, it is highly recommended that you set your user profile first so that the calories will be calculated properly. Go to SET mode/USER. When the Chronograph is stopped and reset in RUN mode, if no activity for 10 minutes, the GPS will be on Standby mode ( GPS ring icon flashing) and return to TIME mode.
GPS Tour 6.2.1. How to START, take LAP, STOP, and SAVE in CHRONO mode • Press S1 to start or re-start. • Press S5 to take LAP. If auto lap function is set, the watch will take lap automatically based on auto lap setting and there is a beep sound during taking of auto lap. • Press S1 to stop after completing your run. 6.2.2. Press S5 to change the information displayed in Line 3 if you have selected a 3ROW display. If you have selected a 2-ROW display, Line 2 information will be changed as you press S5.
GPS Tour 6.3) Using TIMER mode: • Press and hold S1 to save your data RUN mode & TIMER mode has the same chronograph counter. When the chronograph is started or stopped in RUN mode, the same thing happens in TIMER mode. Press S7 to go to TIMER mode from Time mode. • • • • • • The watch has 6 interval timers segment 1 to segment 6. The default values for all segments are 00:00:00. Please set the TIMERS first before using this mode.
GPS Tour 6.3.5. Press S5 while the chronograph is stopped to view your current data before saving. Following are the information as you press S5: How to turn OFF the HRM function of the watch: • • • While HRM is initially ON, press & hold S5 in any mode to turn OFF the HRM function except when the Chronograph in any mode is STOPPED. In this case, you will enter the GO BACK function of the watch. The watch will display HRM OFF and the heart icon will be auto turned OFF also.
GPS Tour 6.4.2. How to change views in HRM mode: •Press S5 to change views. 6.4.3. How to START, take LAP, STOP, and SAVE: • Press S1 to start or re-start. • Press S5 to take LAP. If auto lap function is set, the watch will take lap automatically based on auto lap setting and there is a beep sound during taking of auto lap. • Press S1 to stop after completing your run. • Press and hold S1 or press S11 to save your data. 6.4.4.
GPS Tour 6.5) Using ROUTE mode: 6.5.2. How to START, take LAP, STOP, and SAVE: RUN mode & Route mode has the same chronograph counter. When the chronograph is started or stopped in RUN mode, the same thing happens in Route mode. The Route function is GPS based so you need to select GPS when you enter this mode. Press S7 to go to ROUTE mode and press S5, the watch will start to search GPS. Once the GPS signal is received, the GPS GO screen appears and ready to begin your exercise.
GPS Tour 6.6) Using Altimeter mode: 6.6.2. How to START, take LAP, STOP, and SAVE: RUN mode & Altimeter mode has the same chronograph counter. When the chronograph is started or stopped in RUN mode, the same thing happens in Altimeter mode. The Altimeter function is GPS based so you need to select GPS when you enter this mode. Press S7 to go to ALTIMETER mode and press S5, the watch will start to search GPS. Once the GPS signal is received, the GPS GO screen appears and ready to begin your exercise.
GPS Tour 6.7) Using COMPASS mode: RUN mode & COMPASS mode has the same chronograph counter. When the chronograph is started or stopped in RUN mode, the same thing happens in Compass mode. The Compass function is GPS based so you need to select GPS when you enter this mode. Press S7 to go to COMPASS mode and press S5, the watch will start to search GPS. Once the GPS signal is received, the GPS GO screen appears and ready to begin your exercise. • Press S1 to start or re-start. • Press S5 to take LAP.
GPS Tour 6.8.1. Entering GO BACK mode while in DATA mode: While in selected File Data screen, press S5 to enter VIEW screen then press S1 then press S5. o A new file will be created once you start the GO BACK function. o If there is no GPS signal, or the chronograph is still running, you cannot enter the GO BACK function. o The same procedure to take Lap, STOP, or SAVE in any other exercise modes. 6.8.3. 6.8.2.
GPS Tour 6.8.4. How to view your current data while the chronograph is stopped before saving it. EL backlight: This Watch has a Night mode function. Following are the options in SET mode and their functions: General Operations The Watch has the following main modes: Time, Run, Chronograph, Timer, HRM, Route, Alti, Compass, Data, Alarm and Set modes. Press S7 to scroll through these modes. Press S1 from Time mode will also go to RUN mode. 10 SECONDS – Press S11 will turn ON the Light for 10 seconds.
GPS Tour TIME mode • How to enter TIME mode: While in Time mode, press and hold S1 to change the view from Time 1 to Time 2 and vice versa. DATA mode • Travelling between different Time zones • • • • • When you are traveling to a different Time zone, you have to set your GPS Watch to your destination Time zone. We recommend setting Time 1 to your current location and Time 2 set to your destination Time zone.
GPS Tour • How to view the details of the selected DATA file: Please follow the flow as shown. • How to use the VIEW, GO BACK, DELETE, and DELETE ALL sub menus: Please follow the flow as shown.
GPS Tour Data numbering system/ Legend: Battery: The Watch is using a rechargeable Lithium Ion battery that will require approximately 4 to 5 hours charging time using the USB cable. While battery is charging, the Watch cannot be used and all buttons are disabled. User needs to recharge the battery when the Watch indicates a “low battery”. Battery Life (full charge): 8 hrs typical (continuous GPS).
GPS Tour