HERCULES (Alliance 5W Remote Unit) User Manual SOLiD, Inc.
REVISION HISTORY Version Issue Date V 1.0 July. 14, 2015 No. of Pages Initials Details of Revision Changes Original Technical Support SOLiD serial numbers must be available to authorize technical support and/or to establish a return authorization for defective units. The serial numbers are located on the back of the unit, as well as on the box in which they were delivered. Additional support information may be obtained by accessing the SOLiD Tehcnology, Inc. website at www.solid.co.
Contents Section1 Safety & Certification Notice ......................................................................... 5 Section2 Introduction ................................................................................................ 9 2.1 Purpose ........................................................................................................... 10 2.2 HERCULES ........................................................................................................ 11 2.3 Dimension .....
Contents of Figure Figure 3.1 – Remote Unit Block Diagram 오류! 책갈피가 정의되어 있지 않습니다. Figure 3.2 – Inside of Remote Unit ........ 오류! 책갈피가 정의되어 있지 않습니다. Figure 3.3 – Remote Unit Dimension ................................................................... 12 Figure 4.1 – Exterior of Remote Unit ................................................................... 15 Figure 4.2 – Dimension used to install REMOTE UNIT on the WALL ........................ 16 Figure 4.3 – Procedures of installation ...................
Section1 Safety & Certification Notice Confidential & Proprietary 5/35
“Only qualified personnel should handle the DAS equipment. Any person involved in installation or service of the DAS should understand and follow these safety guidelines.” ‐ Obey all general and regional safety regulations relating to work on high voltage installations, as well as regulations covering correct use of tools and personal protective equipment. - The power supply unit in repeaters contains dangerous voltage level, which can cause electric shock.
‐ A readyily accessible disconnect device shall be incorporated external to the equipment. ‐ The following notice: "The Manufacturer's rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re‐radiated and can cause interference to adjacent band users.
‐ Signal booster warning label message should include ‐ Use of unauthorized antennas, cables, and/or coupling devices not conforming with ERP/EIRP and/or indoor‐only restrictions is prohibited.
Section2 Introduction 2.1 Purpose 2.2 HERCULES 3.
2.1 Purpose HERCULES is a coverage system for in‐building services delivering voice and data in high quality and for seamlessly. As a distributed antenna system, it provides analog and digital phone systems that are served in multiple bands through one antenna. The system covers general public institutions and private facilities. Shopping malls Hotels Campus areas Airports Clinics Subways Multi‐use stadiums, convention centers, etc.
2.2 Modular frequency upgrade Plug‐in type module Multi‐Band, Multi Operator Signals with a plurality of service provider transmit simultaneously Support multi‐operator in a band Low OPEX / CAPEX Compact design Upgradable design Easy installation and maintenance HERCULES Hercules is one of series of Alliance DAS and has 5W composite output power every band.
2.3 Dimension Figure 3.
Section3 System Installation This chapter describes how to install each unit and optical cables, along with power cabling method. In detail, the chapter describes how to install shelves or enclosures of each unit, Power Cabling method and Optic Cabling and RF Interface. The needed accessories and tools are list up in the below table.
Ground Connection OPTIC SC/APC Cable (1EA) X ‐ M6 Screw (1EA) ○ No.2 Screw driver (+) Lug (1EA) ○ Max. AWG #6 Cable X refer 4.1.5 For more details, Crimping Tool refer Connection RF Cable (1 or 2EA) X to 4.1.4 2 Antennal to Spanner (33mm) EA is required in case of MIMO. For more MRDU Installation ‐ ‐ No.1 Screw driver (+) details, refer to 4.1.6 AC power cable (1 EA) [1.
3.1 Remote Unit Installation 3.1.1 Remote Unit Enclosure installation Remote Unit is designed to be water‐ and dirt‐proof. The unit has the structure of one‐Body enclosure. It satisfies water‐proof and quake‐proof standards equivalent of NEMA4(IP66). Basically Remote Unit is attached with wall mountable bracket. Remote Unit can be mounted into either of wall or on a pole. Figure 4.
Figure 4.
Remote Unit Wall Mount Installation Remote Unit’s installation bracket is attached on Enclosure when is delivered. It doesn’t need to remove bracket to install enclosure. simply after installing 4 of M12 mounting bolts, secure 4 mounting bolts tightly First, install 2 of M12 mounting bolts roughly half way on the enclosure and install enclosure over the bolts and secure tightly. Second, install 2 of M12 mounting bolts under the enclosure and secure tightly. Figure 4.
Remote Unit Components Remote Unit has the following components: No.
3.1.2 How to expand ADD ON ROU at the Remote Unit Remote Unit can expand ARU up to 1. The three item is needed for connection between Remote Unit and ADD ON ROU. ADD ON ROU’s components additively have 3 item except for enclosure like below Accessories Description Qty 1 TX RF Cable 1 2 RX RF Cable 1 Specification Remark N(M) ST to SMA(M) ST_1.5M N(M) ST to SMA(M) ST_1.5M IEC 61076‐2‐ 3 I/O Cable 1 101(8pin_F) ST_1.
For expanding ADD ON ROU at the Remote Unit within the proper cable length provided. The cables between Remote Unit and ADD ON ROU have each 1.5m length. Figure 4.4 – Connection diagram between Remote Unit and ADD ON ROU (AC type) Figure 4.
3.1.3 Remote Unit Power Cabling AC Power Remote Unit supports only AC120V of input power. Provided outside power cable is only one type. The pin discription of AC port is below. You should connect exact polarity of AC. Port outlook MS Connector numbering Name Description A AC_H AC Hot B AC_N AC Neutral C N.C Not Connected D F.G Frame Ground Check if the connection is the same as one seen in the table above and make sure to turn the power ON.
3.1.4 Remote Unit Ground cabling The Grounding terminal is located at the bottom of Remote Unit enclosure fixed by M6 screw. Compression terminal is attached already when is delivered. The recommended thickness of cable is AWG#6 copper grounding wire Figure 4.6 – Location of Ground Terminal The specification of compression terminal is like below Figure 4.
The required part number is JOCT 16‐6 supporting AWG 6. The way to install the grounding cable comply with below procedures Figure 4.8 – How to install Ground Terminal The procedures are 1. Loosen a two M6 screws and then take compression terminal off 2. Insert AWG#6 Grounding Wire into terminal and then compress a terminal using tool 3. Assemble the terminal which made in step “2” using 2xM6 screws 4.
3.1.5 Optical Cabling The Optical Connector is located at the bottom of Remote Unit enclosure fixed. Optical Cable can be connected by using connectors. Figure 4.9 – Location of Optical Connector The specification of compression Optic Connector is like below Figure 4.
The way to install the Optical cable comply with below procedures The procedures are Figure 4.
3.1.6 Mounting of MRDU Remote Unit has slots to enable up to six MRDU modules to be mounted in it. You can mount a MRDU into designated slot surely. It is not possible to provide services with a MRDU module alone; you need to connect MRDU cavity duplexer antenna port with CU’s designated port. Installation Diagram for MROU Module Assembly 1) Install each MRDU into its designated location as shown in the graphic.
The Remote Unit holds a maximum of 6 MRDUs. Guide brackets on the bottom of each MRDU slot simplify installation as described below. MRDU installation requires a +No.1 tip size screwdriver. Figure 4.
The procedures are 1. Lift the MRDU onto the guide bracket and ensure the MRDU is level left to right 2. Push the MRDU into the corresponding slot in the direction of the heat sink while levelling the MRDU to guide bracket 3. Make sure the MRDU is firmly inserted into the corresponding slot. Tighten the 4 corner screws to secure the unit 4. Install MRDU blank cards in all unused slots in the remote.
Figure 4.
The procedures are 1. Remove dummy bolt attached at FAN Port 2. Connect internal FAN cable to the FAN Port, and connect with the connector located on the top of PSU. 3. Install fan unit to the bottom of 5W remote with aligning heatsink pin to the guided groove. 4. Secure the fan unit by tightening M6 screw located on the left corner. 5. After securing the FAN Unit, connect the cable from FAN unit to FAN port.
Section4 System Specifications 6.1 Physical Specifications 6.2 RF Performance 6.
4.1 Physical Specifications Parameter Nominal Impedance(input and output) RF Connectors Mounting Type AC Power DC Power Environmental Condition & IP Rating Maximum Power Consumption Enclosure Dimensions (mm) ROU 50 ohm DIN Female (7/16) Wall Mounting (1) RS‐232 9‐pin D‐sub, male (1) SC/APC for ODU Power LED TX LED RX LED LD LED PD LED ALARM LED RESET Button 108~132V AC, 50/60Hz ‐40.8 ~ ‐57.
4.
MRDU 2.5TDD 4.3 Single 47 189.6 -5 2497.8 - 2687.4MHz Certification Title Environmental Temperature range Humidity Range Sealing (Remote Standards Remarks ‐25°C to +55°C/ ‐13 to 131°F 0% ~ 90% Ambient Temperature Non‐condensing IEC 60 529 EN 60 529 IP66 Complaint Unit) RSS‐GEN, Sec. 7.1.2 – (transmitters) Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
RF Radiation Exposure This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 200 cm between the radiator and your body. This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter. RF exposure will be addressed at time of installation and the use of higher gain antennas may require larger separation distances.
