Manufacturer: Gin long Technologies Co. Lid, Bogging, Zhejiang, PR.China US Office: 565 Metro PL 5. Suite 3214, Dublin OH 43017, USA Toll-fro: 866.438.8408 | Email salesperson com | com Web: www.ginlong.com | Please record the serial number of your Inverter and quote this when you contact us, sol PV Nullity Interactive Inverter — U.S. Version Solis Three Phase Inverter (so-skew) install Gin long Technologies Co, Lid.
Important notes # Product specifications are subject to change without notice. Every attempt has been made to make this document complete, accurate and up-to-date.
Contents 1. Introduction — 1.1 Product Description 1.2 Unpacking and storage 1.2.1 Storage 2. Safely instructions 2.1 Safety symbols 2.2 General safely instructions 2.3 Nobles for uss 2.4 Protection Clerestory and Controls 3. Installation 3.1 Environmental considerations 3.1.1 Select a location for the inverter 3.1.4.1 Examples of correct and incorrect installations 3.1.2 Other environmental considerations Consult technical data 3.1.2.2 Vertical wall installation 3.1.2.3 Avoiding direct sunlight 3.1.2.
Contents 1. introduction 8.5.2 Sel Address 6.8 info — Technicians only 6.6.1 Alarm Message 6.6.2 Running Message 6.8.3 Version 6.6.4 Dally Energy #.6.5 Monthly Energy and Yearly Energy 6.6.6 Daily Records 6.6.7 Communication Date 6.6.8 Warning Message £.7 Advanced settings — Technicians only 6.7.1 Select Standard 8.7.2 Grid ON/OFF 8.7.3 Clear Energy 6.7.4 Resat Password 8.7.5 Power Control 6.7.8 Calibrate Energy 6.7.7 Special Settings 5.7.8 STD Mods Settings 6.7.8 Galore Ceilings 8.7.10 Hui Update 6.7.
1. introduction 1. introduction 1.2 Unpacking and storage Wuhan unpacking the Inverter, please verify all the parts listed below are Included: gel ta Inverter x1 Wall maturing bracket Locking resews 4 Locking shes x2 es Fiat washer [g 10) x4 Hagar bot 14 Hexagon nuk x4 manual! 1.2.
2. Safety Instructions 2. Safety Instructions Improper use may result In electric shock hazards or burns. This product manual contain important instructions they are required to be followed during Installation and maintenance, Please read theses Instructions carefully before use and keep them In an easily relocatable place for future reference. 2.
2. Safety Instructions 2.4 Protection Circuitry and Controls To nest relevant codes and standards, the Solis three phase inverter line ls gulped with protective clreullry and controls. These Include Are Fault Clamorous interrupter {AFC} and An fl-lslanding Protection. Are Fault Culture interrupter FACE Edition 2011 of the National Electrical Code®, Section 890.
3. Installation 3. Installation 3.1.1.1 Examples of correct and Incorrect Installations NAME HOT A Units with a fan may be mounted degrees off horizontal 3.1.2 Other environmental considerations 3.1.2.1 Consult technical data Consult the specifications section (section 8) for additional environmental conditions {protection rating, temperatures, humidity, altitude, lee) 3.1.2.
3. Installation 3. Installation Figures 3.3 Handles shown circled in red ars used io remove the Inverter from the shipping box WARNING Due to the weight of the Inverter, contusions or bone fractures A ‘soul augur when incorrectly lifting and mounting the inverter. When mounting the inverter, take the weight of the inverter Into consideration. Use a suitable Sifting technique wham mounting. 3.3 Mounting the inverter The inverter can be mounted to a well or metal array racking.
3. Installation WARNING The Inverter must be mounted vertically on a wall. Ensure the bracket is level before mounting Inverter. Inverter with fans may be mounted at 15.80 degrees off horizontal. #4}. Lit the Inverter and align the slot on the back of the In verier with the lip on the mounting bracket, Slowly lower the inverter onto the bracket until! the inverter is secured on the bracket (see Figure 3.6), L Figure 3.6 Lift and attach ths invader to the mounting basket J 5}.
3. Installation 3.5 DC connection Bbl WARNING Helots congealing the In verier, make sure the PV array open ireful voltage Is within the mit of the Inverter. Otherwise, the Inverter could ba damaged. WARNING DO NOT connect the PY array positive or PY array negative cable to ground.
3. Installation 3. Installation 2}. The fuse rating Is determined based on the PV anal string current and on the sling guidelines provided by the panel manufacturer or the local electrical code. [n addition, the maximum fuse rating must not excess the maximum input current of the inverter, 3.5.3.1 Maximum allowable amperage per fuse and channel Figure 3.10 Shows sight (8) input channels for connecting DC strings. Each channel is protected by a fuse. The included fuses sre rated a1 154.
3. Installation 3. Installation 3.8.2 Wiring procedure ( CAUTION RISK OF ELECTRIC SHOCK. Prior to starting the wiring procedure, ensure that the three-pols circuit breaker is switched off and cannot be reconnected. MOTE Damage or destruction of the Inverter's electronics components dus to moisture and dust Intrusion will scour if the enclosure opening Is enlarged. CAUTION Risk of fora If two conductors are connected to one terminal. Ife connection of two conductors to a terminal is made, a fire can our.
4. Comm. & Monitoring 4. Comm. & Monitoring Overview There are three (3) sets of terminals used for R§485 communication. Terminal 4 (Figure 3.10) has screw terminals for a multiples inverter communication solution using a standard MOD BUS cable such as Baden standard cable. Terminal is a standard F458 terminal and is used for creating a daisy chain connection between inverters as well as the wired date monitoring. Terminal 6 Is a 4-pin connector which Is matched with Soils communication cables.
5. Commissioning 5. Commissioning 5.1 Selecting the appropriate grid standard 5.1.1 Verifying grid standard for country of installation Solis Inverters are used worldwide and feature preset standards for operating on any grid. Although the grid standard is set at ths factory, it is essential the grid standard be verified for the country of installation before commissioning. The menu for changing the grid standard or for creating a custom standard [s accessible as described In Bacon 8.7 and below.
5. Commissioning 5. Commissioning 5.4 Preliminary checks WARMING A High Voltages. AG and DO measurements should be made only by qualified personal. 5.4.1 DC Connections Verity DC connections. 1). Lightly tug on each DC sable to ensure iris fully captured in the terminal, 2}. Visually check for any stray strands that may not be nonsalaried in the terminal. 3}. Check to ensure the terminal screws are the correct torque. 5.4.2 AC Connections Verify AC connections. 1).
5. Commissioning 5.4.4 AC configuration Scarify AC configuration. 5.4.4.1 Measure VAG and frequency Maura VAC and verify voltage ls within local grid standards, 1}. Measure sate phase to ground 2). Measure phases to the other phases In pairs PHA to PHB, PHB to PH C and Hoggish PHA. 3}. the mater is equipped, measures the frequency of each pass to ground. 4}. Ensure sate measurement is within local grid standards and the inverter specifications as noted In Section 8 “Specifications”, 5.4.4.
6. Normal operation 6. Normal operation During normal operation, the LCD shows the current status of the inverter. The LCD will display current power generation, total generation, current AC power In watts and other data In rotation (See Table 8.1). Press the button labeled ESC fo switch from the “home Display Duration Description dashboard” (Le., the Initial Interface for owners and operators} to other screens showing 10 880 W_DG1: Shows input 01 voltage value. details of daily and monthly generation.
6. Normal operation 6. Normal operation 6.4.1 Lock screen Progressing the ESC key returns to the Main Menu. Pressing the ENTER key locks {Figure or unlocks {Figure 8.2 {b}) the screen. Figure 6.2 Locks and Unlocks the Senora of LOD 6.5 Sub-menu: Settings The following sub-menus are displayed when the Settings menu is selected: 1. Bet Tami. 2. Set Address, 6.5.1 Bet Time This function allows time and dale selling. When this function is dialectal, tha LOD will display 8 screen 8% shown in Figure 8.
6. Normal operation 6. Normal operation £.6.2 Running Massage This function is for maintenance personnel to get operational data such as internal temperature, Standard NO. elo. Serpens san be strolled manually by pressing the UP/DOWN keys. Figure 8,12 Monthly energy Figure 8.13 Yearly energy 8.5.3 Version Press UP/DOWN key io move from one date from another. The worsen shows the mods] version and the software version of the Inverter (see Figure 8.7). 6.6.
6. Normal operation 6. Normal operation 6.7.2 Grid ON/OFF This function Is used io snarl or slop the power generation of the Inverter. (see Figure 6.18). Figure 6.18 Sel Grid ON/OFF Select the desired function by pressing the UP/DOWN keys. Press the ENTER key to save the settling. Crass the ESC key to return to the previous menu. §.7.3 Clear Energy Liar Energy can reel the historical yield of Inverter io zero.
6. Normal operation 6. Normal operation 6.7.7.1 Grid Filter Set Crass the ENTER to show the sub menu of Grid Liter Set. Paras ths UP/DOWN key to salacity the value. Paras tha ENTER kay to save the setting and return to the previous menu, A “This function is for maintenance parson only, wrong operation will prevent the inverter from reaching maximum power. J 6.7.7.2 Protectorate Set r \ This function ls for maintenance personal only, wrong operation will prevent the Inverter from reaching maximum power. 6.7.
6. Normal operation 6. Normal operation Suzette £ Net Applicable 4.988 2 Hut BRYCE 125 Anteroom Cessation 138 3 EL. 422 ASBESTOS Ee Continuous Operation ADS 208 Mandatory Propulsion 218 5 Lv2 SUDSY 338 105 Mandatory Caption 240 18 Hortatory Cessation 1.88 Table 8.4 Voltage ride through The voltage and frequency ride through limit is fixed, can't change. Figures 6.23 VITRIFY Set wu 6.7.7.9 comptroller.
6. Normal operation 6. Normal operation 1. HULL Description: Inverter Is not under any working mode. 2. Colt-Wall (Not Required) Description: Inverter will chessmen the active pulp power based on voltage changes. Mote: This Selling is MOT required by UL 174154 Standards. A This function Is for maintenance personnel! only, wrong desperation will prevent the inverter from reaching maximum power, 3. Colt-Var (Default) Description: Inverter will change the reactive output power based on voltage change.
6. Normal operation 6. Normal operation Default Settings for Rule Standards: Rated 480V Grid Villages than Vet art V2 (Avatar: (221-304V) Default 293V V3 (Atop: (277-332V) Default 204V Wa: larger than Veto P1100% PZI00% PR 0% P4D% i | understood 4 underestimated 3. Volt-Var UB sanctified serenity Description: Inverter will sangs the reactive output power based on voltages sangs. Figure 6.33 Fixed-PF Figure 6.34 PF Range ] 1, cap §. Reao-powsr {Not Required) ; Co .
6. Normal operation 6. Normal operation 8. Enable both Volt-Var and Volt-Walt modes Description: Ruler requires both Volt-var and Vol b-watl modes can be enabled. To set both modes (Roll-var in high priority) Step 1: Select and set Volt-wall mode al first. Step 2: Enter "Working Mode” again end select and set Oil-var mods then. Step 3: To check the priority, a new mods will appear as "V-Q & V-P which indicates {Q) Roll-var is in high priority. Figure §.
6. Normal operation 6. Normal operation 6.7.8.4 minsters Voltage Set This function ls dissembled and not used for the US, A This function is for maintenance personal only, wrong operation wheel prevent the Inverter from reaching maximum power, J 6.7.8.5 Power Priority This setting Is used to sel the priority between Active Power Control (Watt) and Reactive Power Control {Var}. ~ Figure §.40 Power Priority J Two options ars available: Wall First and Var First.
6. Normal operation 6. Normal operation Selecting "Restore Settings” displays the option shown below: Figures 5.44 Press the ENTER key to reset io factory defaults. Press the ESC key to return fo the previous menu. 8.7.10 HMI Updater A This section is applicable to maintenance personnel only. Selecting “Updater” displays the sub-menu shown below: Figure 6.45 Updater is for updating LCD firmware. Crass the ENTER key to start the process. Press tha ESC key to return to the previous many. 6.7.
6. Normal operation 7. Maintenance 8.7.14 Compensation Sel This function is used to celibate inverter output energy and voltage. will not impact the energy count for inverter with RGM, Two sections are included: Power Parameter and Voltage Parameter. The screen shows: Figure 8.48 Power Rate Limit Press the Down kay to move the cursor. Tress the Up key to change the digit. Please press the Enter lo save ths sating and press the ESC key to rectum to the previous menu.
7 . Maintenance 7. Maintenance 8). Ra move the screws holding the fan to the fan plate. Replace or clean the fan a8 reacquired. Figure 7.4 Figure 7.1 \ J the screws and remove the fan plate carefully from the bottom of Inverter. 4 h Figure 7.2 . J the power cables and remove the fan assembly from the inverter. Figure Reassemble the fan assembly, 8}. Reconnect the electrical connections and reinstall the fan assembly. 9}. Start the inverter by switching the AC switch ON then the DC switch ON. 81.
8. Troubleshooting 8. Troubleshooting 8.1 Current alarm #.1.1 Running messages Running messages can be viewed on the screen including any current sperms. 8.2 Alarm history 8.2.1 Viewing alarm history Safer to LCD Operation 8.8.8 for instructions on viewing Alarm History. 8.3 Error messages HOTS The first step to clearing alarms as listed in Table 9, is to reset the inverter. To rests the Inverter, tum off tha Inverter {refer to Section 8.
8. Troubleshooting 8.
