BA_U1_MS_270_280_86_01.fm Seite 0 Freitag, 21. Juli 2006 10:22 10 STIH) STIHL MS 270, 280 Instruction Manual Manual de instrucciones Warning! This saw is capabale of servere kickback which may cause serious or fatal injury. Only for users with extraordinary cutting needs and experience and training dealing with kickback. Chainsaws with significantly reduced kickback potential are available. STIHL recommends the use of STIHL reduced kickback bar and low kickback chain.
English / USA © ANDREAS STIHL AG & Co. KG, 2006 0458 146 8621 A. M10,5. H6. CP. Printed in USA Printed on chlorine-free paper. Printing inks contain vegetable oils; paper can be recycled. BA_SE_121_006_01_08.fm Contents Guide to Using this Manual .............. 2 Some Important Safety Precautions for Chain Saw Users ........................ 3 Safety Precautions and Working Techniques ....................................... 5 Mounting the Bar and Chain (Side chain tensioner) ....................
English / USA Guide to Using this Manual Pictograms All the pictograms attached to the machine are shown and explained in this manual. The operating and handling instructions are supported by illustrations. In addition to the operating instructions, this manual may contain paragraphs that require your special attention. Such paragraphs are marked with the symbols described below: Symbols in text Warning where there is a risk of an accident or personal injury or serious damage to property.
English / USA Some Important Safety Precautions for Chain Saw Users A. A Summary of Warnings on kickback and other Selected Risks – Taken Primarily from ANSI B 175.1 (See also the “Safety Precautions“ section of this Owner’s Manual) Do not rely exclusively upon the safety devices built into your saw. As a chainsaw user, you should take several steps to keep your cutting jobs free from accident or injury. 1.
English / USA 4. Use caution when handling fuel. Move the chainsaw at least 10 feet (3 m) from the fueling point before starting the engine. 5. Do not allow other persons to be near the chainsaw when starting or cutting with the chainsaw. Keep bystanders and animals out of the work area. 6. 7. 8. 9. 4 Do not start cutting until you have a clear work area, secure footing, and a planned retreat path from the falling tree.
English / USA Safety Precautions and Working Techniques Because a chainsaw is a high-speed, fast-cutting power tool, special safety precautions must be observed to reduce the risk of personal injury. It is important that you read, fully understand and observe the following safety precautions and warnings. Read the instruction manual and the safety instructions periodically. Careless or improper use may cause serious or fatal injury. !Warning! Reactive forces, including kickback, can be dangerous.
English / USA !Warning! – Prolonged use of a power tool (or other machines) exposing the operator to vibrations may produce whitefinger disease (Raynaud's phenomenon) or carpal tunnel syndrome. These conditions reduce the hand's ability to feel and regulate temperature, produce numbness and burning sensations and may cause nerve and circulation damage and tissue necrosis.
English / USA Wear an approved safety hard hat to reduce the risk of injury to your head. Chainsaw noise may damage your hearing. Wear sound barriers (ear plugs or ear mufflers) to help protect your hearing. Continual and regular users should have their hearing checked regularly. Be particularly alert and cautious when wearing hearing protection because your ability to hear warnings (shouts, alarms, etc.) is restricted.
English / USA Fuel Your STIHL power tool uses an oilgasoline mixture for fuel (see the chapter on “Fuel” of your instruction manual). !Warning! Gasoline is an extremely flammable fuel. If spilled and ignited by a spark or other ignition source, it can cause fire and serious burn injury or property damage. Use extreme caution when handling gasoline or fuel mix. Do not smoke or bring any fire or flame near the fuel or the power tool. Note that combustible fuel vapor may escape from the fuel system.
English / USA Before Starting Take off the chain guard (scabbard) and inspect the saw for proper condition and operation. (See the maintenance chart near the end of the instruction manual.) !Warning! Always check your power tool for proper condition and operation before starting, particularly the throttle trigger, throttle trigger interlock, stop switch and cutting tool. The throttle trigger must move freely and always spring back to the idle position.
English / USA 001BA113 KN 001BA114 KN !Warning! With the first recommended method, the chainsaw is started on the ground. Make sure the chain brake is engaged (see "Chain Brake" chapter in your instruction manual) and place the chainsaw on firm ground or other solid surface in an open area. Maintain good balance and secure footing. The second recommended method for starting your chainsaw allows you to start the saw without placing it on the ground.
English / USA Important Adjustments !Warning! To reduce the risk of personal injury from loss of control and/or contact with the running cutting tool, do not use your unit with incorrect idle adjustment. At correct idle speed, the cutting tool should not move. For directions on how to adjust idle speed, see the appropriate section of your instruction manual. If you cannot set the correct idle speed, have your STIHL dealer check your power tool and make proper adjustments and repairs.
English / USA 001BA082 KN !Warning! 001BA031 KN Position the chainsaw in such a way that your body is clear of the cutting attachment whenever the engine is running. Stand to the left of cut while bucking. !Warning! To reduce the risk of injury from loss of control, never work on a ladder or any other insecure support. Never hold the machine above shoulder height. Do not overreach.
English / USA !Warning! !Warning! !Warning! Inhalation of certain dusts, especially organic dusts such as mold or pollen, can cause susceptible persons to have an allergic or asthmatic reaction. Substantial or repeated inhalation of dust and other airborne contaminants, in particular those with a smaller particle size, may cause respiratory or other illnesses. This includes wood dust, especially from hardwoods, but also from some softwoods such as Western Red Cedar.
English / USA ! Warning! !Warning! !Warning! Inspect buffers periodically. Replace damaged, broken or excessively worn buffers immediately, since they may result in loss of control of the saw. A "sponginess" in the feel of the saw, increased vibration or increased "bottoming" during normal operation may indicate damage, breakage or excessive wear. Buffers should always be replaced in sets. If you have any questions as to whether the buffers should be replaced, consult your STIHL servicing dealer.
English / USA Kickback: Reactive forces including kickback !Warning! The greater the force of the kickback reaction, the more difficult it becomes for the operator to control the saw. Many factors influence the occurrence and force of the kickback reaction. These include chain speed, the speed at which the bar and chain contact the object, the angle of contact, the condition of the chain and other factors. The powerful force used to cut wood can be reversed and work against the operator.
English / USA a) Saws with a displacement of less than 3.8 cubic inches (62 cm³) – must, in their original condition, meet a 45° computer derived kickback angle when equipped with certain cutting attachments, – and must be equipped with at least two devices to reduce the risk of kickback injury, such as a chain brake, low kickback chain, reduced kickback bar, etc. b) Saws with a displacement of 3.
English / USA !Warning! !Warning! Never operate your chainsaw without a front hand guard. In a kickback situation this guard helps protect your left hand and other parts of your body. In addition, removal of the hand guard on a saw equipped with a Quickstop chain brake will deactivate the chain brake. An improperly maintained chain brake may increase the time needed to stop the chain after activation, or may not activate at all.
English / USA Low kickback saw chain and reduced kickback bars STIHL offers a variety of bars and chains. STIHL reduced kickback bars and low kickback chains are designed to reduce the risk of kickback injury. Other chains are designed to obtain higher cutting efficiency or sharpening ease but may result in higher kickback tendency. STIHL has developed a color code system to help you identify the STIHL reduced kickback bars and low kickback chains.
English / USA To avoid kickback STIHL green labeled reduced kickback bars are designed to reduce the risk of kickback injury when used with STIHL green labeled low kickback chains. The best protection from personal injury that may result from kickback is to avoid kickback situations: !Warning! When used with other, more aggressive chains, these bars may be less effective in reducing kickback. 1. Hold the chainsaw firmly with both hands and maintain a secure grip. Don’t let go. 2.
English / USA Cutting Techniques B = Pushback Felling Instructions: Felling Pushback occurs when the chain on the top of the bar is suddenly stopped when it is pinched, caught or encounters a foreign object in the wood. The reaction of the chain may drive the saw rapidely straight back toward the operator and may cause loss of saw control. Pushback frequently occurs when the top of the bar is used for cutting. To avoid pushback 1.
English / USA B Buttress roots C 001BA146 KN 45° A 45° C 001BA143 KN B 001BA040 KN If the tree has large buttress roots, cut into the largest buttress vertically first (horizontally next) and remove the resulting piece. Gunning sight Conventional cut First clear the tree base and work area from interfering limbs and brush and clean its lower portion with an ax. C = felling notch - determines the direction of the fall Then, establish two paths of escape (B) and remove all obstacles.
English / USA C D C 001BA144 KN 001BA150 KN 001BA143 KN D Open-face technique Making sapwood cuts D = Felling cut C = felling notch - determines the direction of the fall : Conventional and open-face technique: For an open-face cut: : Properly place felling notch perpendicular to the line of fall, close to the ground. : Cut down at approx. 50-degree angle to a depth of approx.1/5 to 1/4 of the trunk diameter. : Make second cut from below at approx. 40 degree angle.
English / USA Drive wedges into the felling cut where necessary to control the fall. E !Warning! If the tip of the bar contacts a wedge, it may cause kickback. Wedges should be of wood or plastic - never steel, which can damage the chain. 001BA145 KN 001BA147 KN E E = Hinge MS 270, MS 270 C, MS 280, MS 280 C : Helps control the falling tree. : Do not cut through the hinge – you could lose control of the direction of the fall.
English / USA Plunge-cut method Timber having a diameter more than twice the length of the guide bar requires the use of the plunge-cut method before making the felling cut. First, cut a large, wide felling notch. Make a plunge cut in the center of the notch. 2 1 001BA148 KN 4 Felling cut for large diameter trees: !Warning! Felling a tree that has a diameter greater than the length of the guide bar requires use of either the sectioning felling cut or plunge-cut method.
English / USA !Warning! Enlarge the plunge cut as shown in the illustration. !Warning! There is an extreme danger of kickback at this point. Extra caution must be taken to maintain control of the saw. To make the felling cut, follow the sectioning method described previously. If you are inexperienced with a chainsaw, plunge-cutting should not be attempted. Seek the help of a professional.
English / USA 2 001BA151 KN 1 Bucking Bucking is cutting a log into sections. !Warning! When bucking, do not stand on the log. Make sure the log will not roll downhill. If on a slope, stand on the uphill side of the log. Watch out for rolling logs. Cut only one log at a time. Shattered wood should be cut very carefully. Sharp slivers of wood may be caught and flung in the direction of the operator of the saw. 26 When cutting small logs, place log through "V" - shaped supports on top of a sawhorse.
English / USA MAINTENANCE, REPAIR AND STORING Maintenance, replacement, or repair of the emission control devices and systems may be performed by any nonroad engine repair establishment or individual. However, if you make a warranty claim for a component which has not been serviced or maintained properly or if nonapproved replacement parts were used, STIHL may deny coverage. !Warning! Use only identical STIHL replacement parts for maintenance and repair.
English / USA Mounting the Bar and Chain (Side chain tensioner) The chainsaw should also be returned immediately for maintenance whenever the brake system cannot be thoroughly cleaned or there is a change in its operating characteristics. For any maintenance of the emission control system please refer to the maintenance chart and to the limited warranty statement near the end of the instruction manual. Store chainsaw in a dry place and away from children.
English / USA Mounting the Bar and Chain (Quick chain tensioner) 6 : 143BA003 KN : Wear work gloves to protect your hands from the sharp cutters. : Fit the chain – start at the bar nose. MS 270, MS 270 C, MS 280, MS 280 C 1 Fit the guide bar over the studs (7) – cutting edges on top of bar must point to right – and engage the peg of the tensioner slide in locating hole (8) –- place the chain over sprocket (9) at the same time.
English / USA 4 4 : Remove the tensioning gear (4) and turn it over. : Position the tensioning gear (4) against the guide bar (6) so that the stud (7) projects through the upper hole and the short guide peg (8) locates in the lower hole. 5 133BA028 KN 4 133BA030 KN : 5 Unscrew the nut (5). : 30 Screw the nut (5) on to the stud as far as stop. 133BA031 KN 133BA027 KN 6 8 133BA029 KN 7 Wear work gloves to protect your hands from the sharp cutters. : Fit the chain – start at the bar nose.
English / USA 11 Disengage the chain brake: Pull hand guard (9) towards the front handle. : Turn the guide bar so that the tensioning gear is facing you. : 11 : 133BA033 KN 10 : Fit the chain sprocket cover so that the wingnut locates on the collar screw (11). 133BA034 KN : 133BA035 KN 133BA032 KN 9 Make sure the drive link tangs engage the bar groove (see arrow) and then rotate tensioning gear counterclockwise as far as stop. Fit the chain over the sprocket (10).
English / USA Tensioning the Saw Chain Tensioning the Saw Chain (Side chain tensioner) (Quick chain tensioner) 12 : When fitting the chain sprocket cover, check that the teeth of the tensioning gear and adjusting wheel mesh properly. If necessary, turn the adjusting wheel (12) slightly until the sprocket cover can be pushed flush against the engine housing. Retensioning during cutting work: Retensioning during cutting work: : Shut off the engine first – and then loosen the nuts.
English / USA Checking Chain Tension Fuel 143BA007 KN This engine is certified to operate on unleaded gasoline and the STIHL twostroke engine oil at a mix ratio of 50:1. : Shut off the engine. : Wear work gloves. : Chain must fit snugly against the underside of the bar – and, with the chain brake disengaged, it must still be possible to pull the chain along the bar by hand. : If necessary, retension the chain.
English / USA Fueling Opening the cap Gasoline Oil (STIHL 50:1 or equivalent high-quality oils) Before fueling, clean the filler cap and the area around it to ensure that no dirt falls into the tank. US gal. 1 2 1/2 5 US fl.oz 2.6 6.4 12.8 Always position the machine so that the filler cap points upwards. Dispose of empty mixing-oil canisters only at authorized disposal locations. 34 001BA160 KN : Raise the grip until it is upright. : Turn the cap counterclockwise (approx. a quarter turn).
English / USA Chain Lubricant For automatic and reliable lubrication of the chain and guide bar – use only an environmentally compatible quality chain and bar lubricant with non-fling additive or the rapidly biodegradable STIHL BioPlus is recommended. 001BA162 KN Closing the cap Fit the cap - grip upright -marks must line up. : Turn the cap clockwise as far as stop (approx. a quarter turn). 165BA003 KN : Biological chain oil must be resistant to aging (e.g.
English / USA Filling Chain Oil Tank Checking Chain Lubrication Waste oil does not have the necessary lubricating properties and is unsuitable for chain lubrication. : Thoroughly clean the oil filler cap and the area round it to ensure that no dirt falls into the tank. : Remove the filler cap. : Refill the chain oil tank every time you refuel. : Close the filler cap. There must still be a small amount of oil in the oil tank when the fuel tank is empty.
English / USA Chain Brake The chain brake is designed to be activated also by the inertia of the front hand guard if the forces are sufficiently high. The hand guard is accelerated toward the bar nose - even if your left hand is not behind the hand guard, e.g. during a felling cut. The chain brake will operate only if it has been properly maintained and the hand guard has not been modified in any way.
English / USA Winter Operation The chain brake is subject to normal wear.
English / USA Starting / Stopping the Engine Information Before You Start Starting the Engine STOP STOP 0 146BA001 KN 1 Only Models with Decompression Valve 001BA140 KN : 3 The valve closes automatically as soon as the engine begins to fire. : The four positions of the Master Control lever 2 Press in the button (arrow) to open the decompression valve. For this reason the decompression valve should be pressed in before each starting attempt.
: Place your saw on the ground. Make sure you have a firm footing – check that chain is not touching any object or the ground. Bystanders must be well clear of the general work area of the saw. : Hold the saw firmly on the ground with your left hand on the front handle – your thumb should be under the handle. : Put your right foot into the rear handle and press down. 40 : : Alternative method of starting: Hold the rear handle tightly between your legs, just above the knees.
English / USA At very low outside temperatures: : Allow engine to warm up at part throttle. : Change over to winter operation if necessary – see “Winter Operation”. STOP 0 6 To shut down the engine: : If fuel tank has been run until dry and then refueled: When engine begins to fire: : Press in decompression valve.
English / USA Operating Instructions If the engine doesn’t start: : Unscrew and dry off the spark plug. During break-in period If you did not move the Master Control lever to “Warm Start” n quickly enough after the engine began to fire, the combustion chamber has flooded. : Set the Master Control lever to “Stop” position $ : Press down the interlock lever, open the throttle wide and, at the same time, crank the engine several times with the starter to clear the combustion chamber.
English / USA Taking Care of Guide Bar Check chain tension frequently A new chain has to be retensioned more often than one that has been in use for some time. Chain cold: Tension is correct when chain fits snugly against the underside of the bar and can still be pulled along the bar by hand. Retension if necessary – see “Tensioning the Saw Chain”. Chain at operating temperature: The chain stretches and begins to sag.
English / USA Air Filter System Picco Rapid Rapid Rapid Pitch Minimum groove depth 3/8“ P 0.20" (5.0 mm) 1/4“ 0.16" (4.0 mm) 3/8“; 0.325“ 0.24" (6.0 mm) 0.404“ 0.28" (7.0 mm) The air filter system can be adapted to suit different operating conditions by simply installing a choice of filters. 1 Fabric filter* For normal operating conditions and winter operation. 2 Fleece filter (non-woven)* For dry and very dusty work areas.
English / USA 146BA011 KN 3 : Locate the filter (3) in position (see arrows). : Fit the carburetor box cover. Motor Management Adjusting the Carburetor Exhaust emissions are controlled by the design of the fundamental engine parameters and components (e.g. carburation, ignition, timing and valve or port timing) without the addition of any major hardware.
English / USA Standard Setting H Adjusting Idle Speed L Erratic idling behavior, poor acceleration L : Shut off the engine. Engine stops while idling : Check the air filter and clean or replace if necessary. : Check the standard setting at the low speed screw (L). : Check spark arresting screen* in the muffler and clean or replace it as necessary. : Turn the idle speed screw (LA) clockwise until chain begins to run – then back it off one turn.
English / USA Spark Arresting Screen* in Muffler Only machines with high speed screw (H) Machines with Intelligent Engine Management : If the engine is low on power, check the spark arresting screen in the muffler. Operation at High Altitude The carburetor adjusts automatically to any change in operating conditions (e.g. cutting at high altitude). : Allow muffler to cool down. : Check the standard setting. : Warm up the engine.
English / USA Checking the Spark Plug If engine is down on power, difficult to start or runs poorly at idling speed, first check the spark plug. Remove spark plug – see "Starting / Stopping the Engine". : Clean dirty spark plug. : Check electrode gap (A) and readjust if necessary – see "Specifications". : Use only resistor type spark plugs of the approved range.
English / USA Replacing Starter Rope and Rewind Spring : Remove the remaining rope from the rotor and grip. 1 : Remove the screws (1). : Push the hand guard upward. : Pull the underside of the fan cover away from the fan housing and remove it downward. 2 5 146BA020 KN 1 Use a screwdriver to pry the rope out of the starter grip. 146BA017 KN 1 : : Thread the new rope through the starter grip and tie a simple overhand knot. : Pull the knot back into the grip.
English / USA All Versions 2 3 6 7 : Fit the pawls (4) in the rope rotor. : Fit the washer (3) on the starter post. : Use a screwdriver or suitable pliers to install the spring clip (2) on the starter post and engage it on the pawls’ pegs – the spring clip must point clockwise as shown in the illustration. 146BA019 KN 8 Thread the rope through the top of the guide bushing (6), pull it through the rotor (7) and secure it with a simple overhand knot.
English / USA Storing the Machine Replacing a Broken Rewind Spring : Drain and clean the fuel tank in a well ventilated area. : Dispose of remaining fuel and cleaning solution properly in accordance with local environmental requirements. : Run engine until carburetor is dry, this helps prevent the carburetor diaphragms sticking together. : Remove the saw chain and guide bar, clean them and spray with corrosion inhibiting oil.
English / USA Checking and Replacing Chain Sprocket : : Remove the chain sprocket cover, chain and guide bar. Installing spur sprocket / rim sprocket 5 Disengage the chain brake: Pull hand guard toward the front handle. 6 4 – Replace sooner if the wear marks on the sprocket are deeper than approx. 0.02 in (0,5 mm) since this would reduce the life of the chain. You can use a gauge (“Special Accessories”) to check the depth of the wear marks on sprockets.
English / USA Maintaining and Sharpening Saw Chain Correctly sharpened chain : Clean the chain. : Check the chain for cracks in the links and damaged rivets. : Replace any damaged or worn parts of the chain and match the new parts to the shape and size of the original parts. It is absolutely essential to comply with the angles and dimensions specified below.
English / USA For checking angles 80° 30° 35° : Use a file holder A file holder (special accessory) must be used for manual resharpening (see table "Sharpening Tools"). The correct filing angles are marked on the file holder. 54 0° 90° Use a STlHL filing gauge (special accessory – see table "Sharpening Tools"). This is a universal tool for checking the filing and side plate angles, depth gauge setting and cutter length. It also cleans the guide bar groove and oil inlet holes.
English / USA The file only sharpens on the forward stroke – lift the file off the cutter on the backstroke. : Avoid touching the tie straps and drive links with the file. : Rotate the file at regular intervals while filing to avoid one-sided wear. : Use a piece of hardwood to remove burrs from cutting edge. : Check angles with the filing gauge. All cutters must be the same length. If the cutters are not the same length, they will have different heights.
English / USA : File the top of the depth gauge parallel to the stamped service marking (see arrow) – but do not lower the highest point of the depth gauge in this process. The kickback tendency of the chainsaw is increased if the depth gauges are too low. The other parts of the triple-humped tie strap and humped drive link must not be filed since this may increase the kickback tendency of the chainsaw.
English / USA Complete machine Throttle trigger, trigger interlock, Master Control Chain brake Pickup body/filter in fuel tank Visual inspection (condition, leaks) X Check operation X X Check operation X X X Check X Clean, replace filter element X X X X X Clean Check X Inspect, also check sharpness X X Check chain tension X X X Sharpen X Check (wear, damage) X Clean and turn over X Deburr X Replace Chain sprocket Air filter AV elements (rubber buffers, springs) X X Clean
Carburetor Spark plug All accessible screws and nuts (not adjusting screws) 2) Spark arresting screen* in muffler Chain catcher Safety label Check idle adjustment – chain must not rotate X as required if damaged if problem every 12 months monthly weekly after each refueling stop after finishing work or daily Please note that the following maintenance intervals apply for normal operating conditions only.
English / USA Main Parts of the Saw 1 Carburetor box cover twist lock 2 Carburetor adjusting screws 3 Spark plug boot 4 Decompression valve* 3 5 Chain sprocket cover 4 6 Chain sprocket 1 7 Chain brake # 2 7 6 8 Adjusting wheel of quick chain tensioner* 11 8 9 Side chain tensioner 9 12 10 Chain catcher 11 Bumper spike 13 10 146BA015 KN 5 12 Guide bar 13 Oilomatic saw chain # Serial number 14 Oil filler cap 15 Muffler 17 16 Front hand guard 16 17 Front handle (handlebar) 18 Starter
English / USA Definitions 1. Carburetor Box Cover Twist Lock Lock for carburetor box cover. 2. Carburetor Adjusting Screws For fine tuning the carburetor. 3. Spark Plug Boot Connects the spark plug with the ignition wire. 4. Decompression Valve Releases compression pressure to make starting easier. 5. Chain Sprocket Cover Covers the clutch and the sprocket. 6. Chain Sprocket The toothed wheel that drives the saw chain. 7.
English / USA Specifications Engine STIHL single cylinder two-stroke engine Displacement Bore Stroke Idle speed Weight without bar and chain EPA / CEPA: The Emission Compliance Period referred to on the Emissions Compliance Label indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements.
English / USA Special Accessories Cutting Attachment Recommended cutting attachments for compliance with § 5.11 of ANSI standard B 175.1-2000 (see page 14 of this manual): STIHL reduced kickback bar (with green label) for .325" pitch: Rollomatic with sprocket nose 16, 18 or 20" (40, 45 or 50 cm) STIHL low kickback chain1) (with green label) for 0.
English / USA Ordering Spare Parts Maintenance and Repairs Please enter your saw model, serial number as well as the part numbers of the guide bar and saw chain in the spaces provided. This will make re-ordering simpler. Users of this unit should carry out only the maintenance operations described in this manual. Other repair work may be performed only by authorized STIHL service shops. The guide bar and saw chain are subject to normal wear and tear.
English / USA STIHL Incorporated Federal Emission Control Warranty Statement Your Warranty Rights and Obligations Manufacturer's Warranty Coverage: The U.S. Environmental Protection Agency (EPA) and STIHL Incorporated are pleased to explain the Emission Control System Warranty on your equipment type engine. In the U.S. new 1997 and later model year small off-road equipment engines must be designed, built and equipped, at the time of sale, to meet the U.S. EPA regulations for small non road engines.
English / USA If any emission related part on your engine is defective, the part will be replaced by STIHL Incorporated at no cost to the owner. Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled only for regular inspection to the effect of "repair or replace as necessary" will be warranted for the warranty period.
English / USA Trademarks STIHL Registered Trademarks Some of STIHL’s Common Law Trademarks STIHL PICCO™ BioPlus™ STIHL PowerSweep™ Easy2Start™ STIHL Precision Series™ EasySpool™ STIHL Protech™ ElastoStart™ 4-MIX® STIHL RAPID™ Ematic /Stihl-E-Matic™ AUTOCUT® STIHL SuperCut™ FixCut™ EASYSTART® STIHL Territory™ HT Plus™ OILOMATIC® TapAction™ IntelliCarb™ STIHL Cutquik® TrimCut™ Master Control Lever™ STIHL DUROMATIC® Micro™ STIHL Farm Boss® Pro Mark™ ® STIHL q ( The color combin
español / EE.UU © ANDREAS STIHL AG & Co. KG, 2006 0458 146 8621 A. M10,5. H6. CP. Printed in USA Impreso en papel sin cloro. Las tintas contienen aceites vegetales,el papel es reciclable. BA_SE_121_006_31_08.fm Contenido Guía para el uso de este manual ... 68 Algunas importantes medidas de seguridad para los usuarios de la motosierra ................................... 69 Medidas de seguridad y técnicas de manejo .......................................
español / EE.UU Guía para el uso de este manual Pictogramas Todos los pictogramas que se encuentran en la máquina se muestran y explican en este manual. Las instrucciones de uso y manipulación vienen acompañadas de ilustraciones. Símbolos en el texto Los pasos individuales o procedimientos descritos en el manual pueden estar señalados en diferentes maneras: : Un punto identifica un paso o procedimiento sin referencia directa a una ilustración.
español / EE.UU Algunas importantes medidas de seguridad para los usuarios de la motosierra A.
español / EE.UU 4. Actúe con cautela cuando maneje el combustible. Aléjese con la motosierra una distancia de por lo menos 10 m (3 pies) del punto de abastecimiento de combustible antes de arrancar el motor. 10. No maneje nunca una motosierra que está dañada, mal ajustada o que no fue armada debidamente. Asegúrese que la cadena de la sierra se detiene al soltar el gatillo de aceleración. 5. No deje que otras personas se encuentren cerca de la motosierra durante las operaciones de arranque o corte.
español / EE.UU Medidas de seguridad y técnicas de manejo Dado que la motosierra es una herramienta de corte que funciona a gran velocidad, es necesario tomar medidas especiales de seguridad para reducir el riesgo de lesiones. Es importante que usted lea, comprenda bien y respete las siguientes advertencias y medidas de seguridad. Lea el manual de instrucciones y las instrucciones de seguridad periódicamente. El uso descuidado o inadecuado puede causar lesiones graves o incluso mortales.
español / EE.UU !Advertencia! El uso prolongado de una herramienta motorizada (u otras máquinas) expone al operador a vibraciones que pueden provocar el fenómeno de Raynaud (dedos blancos) o el síndrome del túnel del carpio. Estas condiciones reducen la capacidad de las manos de sentir y regular la temperatura, producen entumecimiento y ardor y pueden provocar trastornos nerviosos y circulatorios, así como necrosis de los tejidos.
español / EE.UU Use un casco aprobado para reducir el riesgo de lesionarse la cabeza. El ruido de la motosierra puede dañar sus oídos. Siempre use amortiguadores del ruido (tapones u orejeras) para protegerse los oídos. Los usuarios constantes y regulares deben someterse con frecuencia a un examen o control auditivo. Esté especialmente alerta y tenga cuidado cuando se usa protectores de oídos, ya que los mismos reducen la posibilidad de oír señales de advertencia (gritos, alarmas, etc.).
español / EE.UU Combustible Su herramienta motorizada de STIHL utiliza una mezcla de aceite y gasolina como combustible (vea el capítulo "Combustible" en el manual de instrucciones). !Advertencia! La gasolina es un combustible muy inflamable. Si se derrama y arde a causa de una chispa u otra fuente de ignición, puede provocar un incendio y quemaduras graves o daños a la propiedad. Tenga sumo cuidado cuando manipule gasolina o la mezcla de combustible.
español / EE.UU Para apretar las tapas con ranuras, se puede usar el extremo de destornillador de la llave combinada de STIHL u otra herramienta similar. Consulte el capítulo "Llenado de combustible" en el manual de instrucciones. Antes de arrancar Quite el protector de la cadena (la funda) e inspeccione la motosierra para verificar que está en buenas condiciones de funcionamiento. (Consulte la tabla de mantenimiento cerca del final de este manual de instrucciones.
español / EE.UU 001BA113 KN 001BA114 KN !Advertencia! Con el primer método recomendado, la motosierra se arranca apoyada en el suelo. Asegúrese que el freno de la cadena esté aplicado (vea el capítulo "Freno de la cadena" en el manual de instrucciones) y apoye la motosierra sobre terreno firme u otra superficie sólida en un lugar abierto. Mantenga el equilibrio y elija un buen punto de apoyo para los pies.
español / EE.UU Ajustes importantes !Advertencia! Para reducir el riesgo de lesiones personales debido a la pérdida de control y/o al contacto con la herramienta de corte en movimiento, no use una máquina cuyo ralentí está mal regulado. Cuando el ralentí está correctamente regulado, la herramienta de corte no debe moverse. Para instrucciones acerca de cómo ajustar la velocidad de ralentí, vea la sección correspondiente del manual de instrucciones.
español / EE.UU medidas de precaución para evitar ser lesionado por las ramas que caen. persona. No deje que otras personas estén en el lugar de trabajo, aun durante el arranque. Apague el motor inmediatamente si se le aproxima alguna persona. 001BA031 KN 001BA082 KN !Advertencia! !Advertencia! Para reducir el riesgo de lesiones causadas por la pérdida del control, nunca trabaje sobre una escalera o cualquier otra superficie de soporte poco seguro.
español / EE.UU !Advertencia! !Advertencia! La inhalación de ciertos polvos, especialmente los polvos orgánicos, tales como el moho o polen, puede provocar reacciones alérgicas o asmáticas en las personas sensibles. La inhalación repetida o de grandes cantidades de polvo u otros contaminantes del aire, especialmente los de partículas pequeñas puede causar enfermedades respiratorias o de otro tipo.
español / EE.UU o exceso de desgaste. Los amortiguadores siempre deben sustituirse en juegos. Ante cualquier duda al respecto, consulte a su concesionario de servicio STIHL. enfríe apoyado sobre una superficie de hormigón, metal, suelo raso o madera maciza (por ej., el tronco de un árbol caído) lejos de cualquier sustancia combustible. !Advertencia! !Advertencia! La motosierra no está diseñada para ser utilizada como palanca o pala en las ramas, raíces u otros objetos.
español / EE.UU Contragolpe: La gran fuerza utilizada para cortar madera puede cambiar de sentido y actuar contra el operador. Si una cadena en movimiento se detiene repentinamente al tocar un objeto sólido como por ejemplo un tronco o rama, o bien queda aprisionada, pueden presentarse de inmediato las fuerzas reactivas. Esas fuerzas reactivas pueden causar la pérdida del control, lo que a su vez puede causar lesiones graves o mortales.
español / EE.UU a) Las sierras con una cilindrada inferior a 62 cm³ (3,8 pulg³) – deben tener, en su condición original, un ángulo de contragolpe de 45° calculado por computadora cuando están equipadas con ciertos accesorios de corte, – y deben tener por lo menos dos dispositivos para reducir el riesgo de lesiones por contragolpe, tales como un freno de la cadena, cadena de bajo contragolpe, espada de contragolpe reducido, etc.
español / EE.UU Vea el capítulo titulado "Freno de la cadena" en el manual de instrucciones. !Advertencia! !Advertencia! Un freno de la cadena mal cuidado puede aumentar el tiempo necesario para detener la cadena después de la activación, o simplemente puede no activarse. Nunca maneje la motosierra sin tener instalado el protector delantero de la mano. En una situación de contragolpe este protector ayuda a proteger la mano izquierda y otras partes del cuerpo.
español / EE.UU Cadena de sierra de bajo contragolpe y espadas de contragolpe reducido STIHL ofrece una variedad de espadas y cadenas. Las espadas de contragolpe reducido y las cadenas de bajo contragolpe de STIHL están diseñadas para reducir el riesgo de lesiones causadas por contragolpe. Otras cadenas están diseñadas para obtener un rendimiento de corte mayor o para facilitar el afilado, pero pueden producir una mayor tendencia a los contragolpes.
español / EE.UU !Advertencia! Una cadena roma o mal afilada puede reducir o anular los efectos de las características del diseño que deben reducir la fuerza de contragolpe. Una reducción o afilado incorrecto de los calibradores de profundidad o la alteración de la forma de las cuchillas puede aumentar la posibilidad y la fuerza potencial de un contragolpe. Siempre corte con una cadena bien afilada.
español / EE.UU Para evitar el rechazo !Advertencia! 1. Tenga sumo cuidado cuando corte arbolitos y matorrales pequeños que pueden enredarse fácilmente en la cadena, ser lanzados contra usted o hacerle perder el equilibrio. Para evitar los tirones 1. Siempre empiece el corte con la cadena girando a velocidad máxima y la púa de tope en contacto con la madera. 2. El tirón también se puede reducir colocando cuñas para abrir la entalla o el corte.
español / EE.UU Raíces de zancos grandes !Advertencia! El ruido del motor puede apagar las llamadas de advertencia. 001BA146 KN B C 45° Si el árbol tiene raíces de zancos grandes, corte primero en el zanco más grande verticalmente (después horizontalmente) y retire el trozo cortado.
español / EE.UU C D C 001BA144 KN 001BA150 KN 001BA143 KN D Técnica de cara libre Para hacer cortes de albura D = Corte de tala C = entalla de tala - determina el sentido de caída del árbol : Técnica convencional y de cara libre: Para un corte de cara libre: : : Coloque debidamente la entalla de tala perpendicular a la línea de caída, cerca del suelo. Corte hacia abajo en un ángulo de aproximadamente 50° hasta una profundidad de aprox. 1/5 a 1/4 del diámetro del tronco.
español / EE.UU Inserte cuñas en el corte de tala donde sea necesario para controlar la caída. E !Advertencia! Si la punta de la espada hace contacto con una cuña, puede producirse un contragolpe. Las cuñas deben ser de madera o de plástico, pero jamás de acero porque se dañaría la cadena. 001BA145 KN 001BA147 KN E E = Eje de inclinación : Ayuda a controlar la caída del árbol. : No corte a través del eje – podría perder el control del sentido de la caída.
español / EE.UU Método de corte por penetración La madera cuyo diámetro es más del doble del largo de la espada requiere el uso del método de corte por penetración antes de hacer el corte de tala. Primero, corte una entalla de tala grande y ancha. Haga un corte por penetración en el centro de la entalla. 2 1 001BA148 KN 4 !Advertencia! Para talar un árbol cuyo diámetro es mayor que el largo de la espada es necesario emplear el método de corte de tala por secciones o de corte por penetración.
español / EE.UU !Advertencia! Agrande el corte por penetración como se muestra en la ilustración. !Advertencia! En este momento existe un gran peligro de que ocurra contragolpe. Preocúpese de mantener el control de la sierra. Para hacer el corte de tala, emplee el método de corte por secciones descrito anteriormente. Si no tiene experiencia en el manejo de una motosierra, no intente hacer el corte por penetración. Pida la ayuda de un profesional.
español / EE.UU 2 001BA151 KN 1 Tronzado El tronzado consiste en cortar un tronco en secciones. !Advertencia! Durante el tronzado, no se suba al tronco. Asegúrese que el tronco no vaya a rodar cerro abajo. Si se encuentra en una ladera, sitúese cerro arriba del tronco. Esté atento a los troncos que pueden rodar. Corte solamente un tronco a la vez. La madera astillada deberá cortarse con mucho cuidado. Las astillas afiladas pueden atraparse y salir lanzadas hacia el operador.
español / EE.UU MANTENIMIENTO, REPARACION Y ALMACENAMIENTO Los trabajos de mantenimiento, reemplazo o reparación de los dispositivos y sistemas de control de emisiones de escape pueden ser realizados por cualquier taller o técnico de motores no diseñados para vehículos. Sin embargo, si usted está reclamando cobertura de garantía para algún componente que no ha sido reparado o mantenido debidamente, o cuando se utilizan repuestos no autorizados, STIHL puede denegar la garantía.
español / EE.UU Montaje de la barra y la cadena (Tensor lateral de la cadena) 94 1 2 En esta motosierra se pueden usar cadenas de pasos diferentes, dependiendo de la rueda dentada de la cadena (vea las "Especificaciones"): 143BA034 KN 3 : Destornille las tuercas y retire la cubierta de la rueda dentada de la cadena. El paso de la cadena (1) debe coincidir con el paso de la rueda dentada y la barra guía (para Rollomatic).
español / EE.UU Montaje de la barra y la cadena (Tensor rápido de la cadena) 6 Use guantes para proteger las manos de los cortadores afilados. : Coloque la cadena – empiece por la punta de la barra.
español / EE.UU 4 4 Retire el engranaje tensor (4) e inviértalo. : Coloque el engranaje tensor (4) contra la barra guía (6) de tal modo que el espárrago (7) sobresalga por el agujero superior y la clavija guía corta (8) quede en el agujero inferior. 4 133BA028 KN 5 Desenrosque la tuerca (5). : 96 Use guantes para proteger las manos de los cortadores afilados. 5 133BA030 KN : Coloque la tuerca (5) en el espárrago y apriétela hasta que tope.
español / EE.UU 11 Suelte el freno de cadena: Tire del protector (9) de la mano hacia el mango delantero. : Gire la barra guía de modo que el engranaje tensor esté hacia usted. 11 : 133BA033 KN 10 : : Coloque la cubierta de la rueda dentada de la cadena de modo que la tuerca mariposa se sitúe en el tornillo del collar (11).
español / EE.UU Tensado de la cadena de sierra Tensado de la cadena de sierra (Tensor lateral de la cadena) (Tensor rápido de la cadena) 12 : : : Cuando coloque la cubierta de la rueda dentada de la cadena, compruebe que los dientes del engranaje tensor y de la rueda de ajuste engranen correctamente. De ser necesario, gire un poco la rueda de ajuste (12) hasta que la cubierta de la rueda dentada pueda empujarse al ras con la caja del motor.
español / EE.UU Revisión de tensión de la cadena Combustible 143BA007 KN Este motor está certificado para funcionar con una mezcla de 50 a 1 de gasolina sin plomo y aceite STIHL para motores de dos tiempos. : Apague el motor. : Póngase guantes de trabajo. : La cadena debe quedar ajustada contra la parte inferior de la barra y, con el freno de cadena desconectado, debe poderse tirar de la cadena a lo largo de la barra con la mano. : De ser necesario, vuelva a tensar la cadena.
español / EE.UU Llenado de combustible Duración de la mezcla de combustible gal EE.UU. 1 2 1/2 5 Aceite (STIHL 50:1 ó aceite de calidad equivalente) oz fl EE.UU. 2.6 6.4 12.8 Deseche los envases vacíos usados para mezclar el aceite únicamente en vertederos autorizados para ello. 100 Antes de llenar la máquina con combustible, limpie a fondo la tapa de llenado y la zona alrededor del mismo para evitar la entrada de tierra al tanque.
español / EE.UU Lubricante de la cadena Para una lubricación automática y segura de la cadena y la barra guía – se recomienda el uso exclusivo de un lubricante para cadena y barra guía no dañino para el ambiente con aditivo antisalpicaduras o el aceite STIHL Bioplus. : Coloque la tapa, con la empuñadura en posición vertical y las marcas alineadas : Gire la tapa en sentido horario hasta donde tope (aprox.
español / EE.UU Llenado del tanque de aceite de la cadena El aceite de desecho no tiene las propiedades lubricantes necesarias y no es adecuado para la lubricación de cadenas. : Limpie a fondo la tapa de llenado de aceite y la zona alrededor de la misma para evitar la entrada de suciedad al tanque. : Quite la tapa de llenado. : Llene el tanque de aceite de la cadena cada vez que se llene con combustible la máquina. : Cierre la tapa de llenado.
español / EE.UU Freno de cadena Inmovilización de la cadena con el freno de cadena – en caso de emergencia – durante el arranque – a velocidad de ralentí La cadena se detiene y bloquea cuando se empuja el protector de la mano hacia la punta de la barra con la mano izquierda, o cuando el freno se activa por inercia en ciertos casos de contragolpe.
español / EE.UU Manejo durante el invierno El freno de cadena está expuesto a desgaste normal.
español / EE.UU Información previa al arranque Arranque / Parada del motor Arranque del motor STOP STOP 0 146BA001 KN 1 Solamente los modelos con válvula de descompresión 001BA140 KN : $ = Motor apagado – el interruptor de encendido está en la posición de apagado. # = Posición de funcionamiento normal – el motor está en marcha o puede arrancarse. Para mover la palanca de control maestro de la posición # a la n o l, oprima el bloqueo del gatillo de aceleración y oprima el gatillo al mismo tiempo.
: Coloque la motosierra sobre el suelo. Asegúrese de tener los pies bien apoyados – verifique que la cadena no esté en contacto con ningún objeto ni con el suelo. Las personas ajenas al trabajo deben mantenerse alejadas de la zona general de uso de la sierra. : Sujete firmemente la sierra en el suelo con la mano izquierda en el mango delantero – el pulgar debe quedar debajo del mango. : Ponga el pie derecho en el mango trasero y presione hacia abajo.
español / EE.UU A temperaturas ambiente muy bajas: STOP 0 : Deje que el motor se caliente a aceleración parcial. : De ser necesario, cambie al ajuste para uso durante el invierno – vea "Manejo durante el invierno". 6 Para apagar el motor: : Cuando el motor empieza a encenderse: : Presione la válvula de descompresión.
español / EE.UU Instrucciones de manejo Si el motor no arranca: : Destornille y seque la bujía. Durante el período de rodaje Si no se mueve la palanca de control maestro a la posición de "arranque en caliente" n en un tiempo suficientemente corto después que el motor ha empezado a encenderse, la cámara de combustión se "ahogará".
español / EE.UU Cuidado de la barra guía Revise frecuentemente la tensión de la cadena Es necesario volver a tensar las cadenas nuevas con mayor frecuencia que las que han estado en uso por algún tiempo. Cadena fría: La tensión es correcta cuando la cadena encaja ajustadamente contra la parte inferior de la barra y todavía puede ser tirada a lo largo de la barra con la mano. Ténsela nuevamente de ser necesario – Vea "Tensado de la cadena de sierra".
español / EE.UU Sistema de filtro de aire Paso Picco 3/8 pulg P Rapid 1/4 pulg Rapid 3/8 pulg; 0,325 pulg 0,404 pulg Rapid Profundidad mínima de ranura 0.20 pulg (5.0 mm) 0.16 pulg (4.0 mm) 0.24 pulg (6.0 mm) 0.28 pulg (7.0 mm) Es posible adaptar el sistema de filtro de aire para diferentes condiciones de trabajo, simplemente instalando una variedad de filtros. 1 Filtro de tela* 2 Para condiciones de funcionamiento normales y manejo durante el invierno.
español / EE.UU 146BA011 KN 3 : Coloque el filtro (3) en posición (vea las flechas). : Ponga la cubierta de la caja del carburador. Manejo del motor Ajuste del carburador Las emisiones de gases de escape son controladas por el diseño de parámetros y componentes fundamentales del motor (por ej. carburación, encendido, regulación y regulación de la válvula o lumbrera) sin la adición de ningún equipo importante.
español / EE.UU Ajuste estándar H Ajuste de ralentí L Funcionamiento irregular a ralentí, aceleración deficiente L : Apague el motor. : Revise el filtro de aire y límpielo o sustitúyalo de ser necesario. : Revise el chispero* en el silenciador y límpielo o sustitúyalo de ser necesario. Gire el tornillo de baja velocidad (L) hasta el tope en sentido horario. Después gírelo en sentido contrario un cuarto de vuelta.
español / EE.UU Chispero* en silenciador Máquinas con tornillo de ajuste de velocidad alta (H) solamente Máquinas con Gestión inteligente del motor Funcionamiento en alturas grandes El carburador se ajusta automáticamente a los cambios de condiciones de trabajo (tal como cuando se trabaja a alturas grandes). : Revise el ajuste estándar. : Caliente el motor. : Gire el tornillo de ajuste de velocidad alta (H) en sentido horario (mezcla más pobre), pero no más allá del tope.
español / EE.UU Revisión de la bujía La mezcla de combustible incorrecta (demasiado aceite de motor en la gasolina), el filtro de aire sucio y condiciones de funcionamiento desfavorables (generalmente a media aceleración, etc.) afectan la condición de la bujía. Estos factores causan la formación de depósitos en la punta del aislador lo que puede dificultar el funcionamiento. 114 : Saque la bujía – vea „Arranque / parada del motor“. : Limpie la bujía sucia.
español / EE.UU Sustitución de la cuerda de arranque y resorte de rebobinado 1 146BA017 KN 1 1 : Saque los tornillos (1). : Empuje el protector de mano hacia arriba. : Aparte del caja del ventilador la parte inferior de la cubierta del ventilador y retírela hacia abajo. : Utilice un destornillador para apalancar y quitar la cuerda del mango de arranque. : Quite el resto de la cuerda del rotor y del mango.
español / EE.UU Todas las versiones 2 3 6 : Instale los trinquetes (4) en el rotor de la cuerda. : Instale la arandela (3) en el poste del arrancador. : Use un destornillador o alicates adecuados para instalar la pinza de resorte (2) en el poste del arrancador y sobre los vástagos de los trinquetes – la pinza de resorte debe apuntar en sentido horario como se muestra en la ilustración.
español / EE.UU Almacenamiento de la máquina Sustitución del resorte de rebobinado roto : Vacíe y limpie el tanque de combustible en una zona bien ventilada. Deseche los residuos de combustible y solución de limpieza de acuerdo con los requerimientos locales de protección del medio ambiente. Haga funcionar el motor hasta que el carburador se seque, esto ayuda a evitar que los diafragmas del carburador se peguen. : Quite la cadena y la espada, límpielas y rocíelas con aceite inhibidor de corrosión.
español / EE.UU Revisión y sustitución de la rueda dentada de cadena : : Quite la cubierta de la rueda dentada, la cadena y la barra guía. Instalación de la rueda con dientes rectos / rueda dentada tipo llanta 5 Suelte el freno de cadena: Tire del protector de la mano hacia el mango delantero. 6 : Limpie la caja de cojinetes de aguja y la punta del cigüeñal y lubrique con grasa STIHL ( “Accesorios especiales”). : Empuje la caja de cojinetes de aguja sobre el cigüeñal.
español / EE.UU Mantenimiento y afilado de la cadena de sierra Cadena debidamente afilada : Limpie la cadena. : Revise la cadena en busca de roturas en sus eslabones y daños en sus remaches. : Sustituya todas las piezas dañadas o desgastadas de la cadena e instale piezas nuevas que tengan la misma forma y tamaño que las originales. Es absolutamente esencial cumplir con los ángulos y dimensiones abajo especificados.
español / EE.UU 90° 85° 70° 60° 80° 30° 35° : Use un portalima Se debe usar un portalima (accesorio especial) para afilar manualmente la cadena (vea la tabla "Herramientas de afilado"). Los ángulos de rectificación correctos están marcados en el portalima. 120 0° 90° Utilice un calibrador de rectificación STIHL (accesorio especial – vea la tabla "Herramientas de afilado").
español / EE.UU La lima afila únicamente en la pasada de ida – quite la lima del cortador para la pasada de retorno. : Evite tocar las amarras y eslabones impulsores con la lima. : Gire la lima a intervalos regulares al limar para evitar desgastar uno de sus lados solamente. : Utilice un trozo de madera dura para quitar las rebabas del borde cortante. : Compruebe el ángulo con el calibrador de rectificación. El ajuste del calibrador de profundidad se reduce cuando se afila la cadena.
español / EE.UU : Las otras partes de la pletina de amarre de tres salientes y el eslabón impulsor con saliente no deben afilarse ya que eso podría aumentar la tendencia de la motosierra a dar contragolpes. 689BA052 KN 689BA044 KN RSC3, RMC3, PMC3: La parte superior del eslabón impulsor con saliente (con la marca de servicio) se baja junto con el calibrador de profundidad.
español / EE.
Elementos AV (amortiguadores de caucho, resortes) Inspeccionar X X Solicitar al concesionario de servicio su reemplazo1) X Entradas de enfriamiento Limpiar X Aletas del cilindro Limpiar X Carburador Comprobar ajuste de ralentí – la cadena no debe girar X X X X Ajustar el ralentí X Ajustar la distancia entre electrodos Bujía Todos los tornillos y tuercas accesibles (salvo los tornillos de ajuste) 2) Chispero en silenciador* Gancho retenedor de la cadena Etiquetas de seguridad Cambiar despué
español / EE.
español / EE.UU Definiciones 1. Bloqueo giratorio de la cubierta de la caja del carburador. Traba la cubierta de la caja del carburador. 2. Tornillo de ajuste del carburador Para afinar el carburador. 3. Casquillo de la bujía. Conecta la bujía al alambre de encendido. 4. Válvula de descompresión. Facilita el arranque. 5. Cubierta de la rueda dentada de la cadena. Cubre el embrague y la rueda dentada. 6. Rueda dentada de la cadena. Una rueda con dientes que impulsa la cadena de sierra. 7. Freno de cadena.
español / EE.UU Especificaciones Motor Motor STIHL de un cilindro, dos tiempos MS 270 Cilindrada Diámetro Carrera Velocidad de ralenti Peso (sin espada y cadena) EPA / CEPA: El período de cumplimiento de emisiones indicado en la etiqueta de cumplimiento de emisiones es la cantidad de horas de funcionamiento para la cual la máquina ha demostrado la conformidad con los requerimientos de emisiones del Gobierno federal de los EE.UU.
español / EE.UU Accesorios especiales Accesorio de corte Accesorios de corte recomendados de conformidad con § 5.11 de la norma B 175.1-2000 de ANSI (vea la página 81 de este manual): Espada de contragolpe reducido STIHL (con etiqueta verde) para paso de .325“ pulg: Rollomatic con punta de rueda dentada de 40, 45 ó 50 cm (16, 18 ó 20 pulg) Cadena de bajo contragolpe STIHL1) (con etiqueta verde) para paso de 0.
español / EE.UU Pedido de piezas de repuesto Mantenimiento y reparaciones Sírvase anotar el modelo de su motosierra, el número de serie, como también los números de pieza de la barra guía y la cadena de sierra en los espacios provistos. Con ello se facilitará el pedido. Los usuarios de esta máquina deben efectuar únicamente los trabajos de mantenimiento descritos en este manual. Solamente los talleres autorizados por STIHL deben llevar a cabo los demás trabajos de reparación.
español / EE.UU Declaración de garantía de STIHL Incorporated sobre sistemas de control de emisiones según normas Federales Sus derechos y obligaciones de garantía La Agencia de Protección del Medio Ambiente (EPA) de los EE.UU. y STIHL Incorporated se complacen en explicarle la garantía del sistema de control de emisiones instalado en el motor de su equipo. En los EE.UU.
español / EE.UU subsiguiente que el motor está libre de defectos en el material y fabricación que puedan causar el incumplimiento de los reglamentos aplicables durante un período de dos años. Período de garantía El período de garantía comienza en la fecha en que el motor del equipo utilitario es entregado al primer propietario y el mismo firma y remite la tarjeta de garantía a STIHL.
español / EE.
BA_U4_86_01.fm Seite 1 Freitag, 21. Juli 2006 10:23 10 ! WARNING! ! ADVERTENCIA! The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. El gas de escape del motor de esta máquina contiene productos químicos que en el estado de California son considerados como causantes de cáncer, defectos de nacimiento u otros efectos nocivos para los órganos de la reproducción.