MultiPort PCI English Hardware Manual 2010.12.06 Version 1.
Revision History Revision History Revision Date Version Pages Description 10/24/2008 1.0 All Renewal by hjnoh 01/30/2009 1.1 Partial Added by msbaek 12/07/2009 1.2 Partial Added by ymwon 02/09/2010 1.3 Partial Added by ymwon 12/06/2010 1.4 Partial Fixed by ymwon Copyright 2006 SystemBase Co., Ltd. All rights reserved. Internet Webpage: http://www.sysbas.
Contents Contents Greetings from CEO ............................................................................................................... 7 About MultiPort .............................................................................................................................. 8 About PCI ...................................................................................................................................... 9 Isolation ..........................................................
Contents Multi-2/PCI VA3 ........................................................................................................................... 43 - Product Specifications........................................................................................................ 43 - RS232 Model ..................................................................................................................... 44 - RS422/RS485 Combo Model....................................................................
Contents - RS485 Model ..................................................................................................................... 88 Multi-4J/PCI VA2 ......................................................................................................................... 89 - Product Specifications........................................................................................................ 89 -RS232, Combo Common .........................................................................
Contents - RS422 Model ................................................................................................................... 119 - RS485 Model ................................................................................................................... 120 Multi-8/LPCI VA2 ....................................................................................................................... 121 - Product Specifications......................................................................
Greetings from CEO Greetings from CEO We appreciate all the customers for their deep interest in our products. SystemBase has been engaged wholly in the field of the serial communications to produce the various products related to the same since it was founded in 1987. Along with the recent booming market trend by the advanced skill of high speed communication applying LAN the applicable field of this serial communications could not draw the attention of the public.
About MultiPort About MultiPort MultiPort is a multi serial communication device which makes PC to a multi-user or Multi device system by applying it. Multi-user system or RAS(Remote Access System) is a system which enables a server computer to be used together by multi users thru the terminal at distance or to have the information used together.
About PCI About PCI PCI(Peripheral Component Interconnect) is a type of local bus that connects CPUs and internal peripherals. In 1991, PCI was proposed by Intel Corporation for the first time, but now it is a local bus standard so that PCs, and even medium and large computer systems can adopt it. A few features of PCI bus can be summarized as follows. The PCI is basically designed to operate at 33 MHz clock speed and 32 bit I/O.
Isolation Isolation What is Isolation? ISO version boards and panels include an embedded isolator to provide isolation feature. Isolator cuts off the electric route between the input and output by inserting an appropriate shock absorber. This feature protects the device from the power crash. Product Features Securely protects the product from electric shock with opto coupler and DC-DC converter that electrically isolate the power and signal lines.
Synopsys Synopsis SystemBase MultiPort PCI boards are installed on a PCI slot of your PC, providing 1, 2,4,8,16,24 or 32 RS 232/RS422/RSs485 serial ports. Multi-1/PCI, Multi-2/PCI, Multi-4/PCI, Multi-8/PCI MultiPort boards provide one, two, four and eight serial ports respectively. Multi-32/PCI MultiPort board is composed of 8, 16, 24, 32 ports with the extended external port box, Each port complies with standard UART for both-way communication at up to 921,600 bps.
Multi-1/PCI VA1 Multi-1/PCI VA1 Multi-1/PCI VA1 board is a model that supports PCI Local Bus Spec 2.3. It is an asynchronous single port product designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-1/PCI uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-1/PCI VA1 not only supports maximum communication speed of 921.
Multi-1/PCI VA1 - RS232 Model 1. 9 Pin Connector (Male) 2. Connecting Terminal 3.
Multi-1/PCI VA1 - RS422 Model 1. 9 Pin Connector (Male) 2. Mode Change Select between point-to-point mode and multi-drop mode during the installation of the device driver. The default mode is point-to-point mode. 3. Connecting External Point-to-Point 4.
Multi-1/PCI VA1 - RS485 Model 1. 9 Pin Connector (Male) 2. Mode Change Select between non-echo mode and echo mode during the installation of the device driver. The default mode is non-echo mode. 3.
Multi-1ALL/PCI Multi-1 ALL/PCI Multi-1 ALL/PCI board is a model that supports PCI Local Bus Spec 2.3. It is designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-1 ALL/PCI uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-1 ALL/PCI not only supports maximum communication speed of 921.6Kbps but also provides different communication interfaces, RS232/RS422/RS485, with simple jumper setting.
Multi-1ALL/PCI - RS232 Model 1. RS232 Connector Pin-outs 9 Pin Connector (Male) 5V, 12V Power can be supplied through 9-pin connector, using the board jumper setting 2.
Multi-1ALL/PCI 3. Connecting Terminal 4.
Multi-1ALL/PCI - RS422 Model 1. 9 Pin Connector (Male) 2. RS422 Jumper Configuration 3. Mode Change When installing the device driver, select either point-to-point mode or multi-drop mode by software. The default is point-to-point mode. 4.
Multi-1ALL/PCI 5.
Multi-1ALL/PCI - RS485 Model 1. 9 Pin Connector (Male) 2. RS485 Jumper Configuration 3. Mode Change When installing the device driver, select either non-echo mode or echo mode by software. The default is non-echo mode. 4.
Multi-1ALL/PCI 5. Terminal Resistance Setting JP4 JP5 JP4: RS 485 Communication Terminal Resistance JP5: RS 422 Communication Terminal Resistance Terminal resistance only connects to terminal channels in RS422 or RS485. Multi-1 All/PCI can independently connect to the terminal resistance, using the Jumper Switch Jumper for the matching channel should be connected when the connection of the terminal resistance is desired.
Multi-1/LPCI VA2 Multi-1/LPCI VA2 Multi-1/LPCI VA2 board is a model that supports PCI Local Bus Spec 2.3. It is an asynchronous single port product designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-1/LPCI VA2uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-1/LPCI VA2 not only supports maximum communication speed of 921.
Multi-1/LPCI VA2 - RS232, Combo Common 1. Port1: External Power Supply Setting Jumper RI: Do not supply external power and use pin 9 for RI signal line. +5V: Use pin 9 for supplying +5V external power. +12V: Use pin 9 for supplying +12V external power. In case you want to supply +5V power but the PCI slot does not supply it, you should use PC’s power supply.
Multi-1/LPCI VA2 - RS232 Model 1. 9 Pin Connector (Male) 2. Connecting Terminal 3.
Multi-1/LPCI VA2 - RS422/RS485 Combo Model Combo refers to products that can alternatively use RS422 or RS485 using jumper settings 1. 9 Pin Connector (Male) 2. Jumper Settings a. Interface Settings: Interface Selection 422: Select RS422 Interface 485: Select RS485 Interface b.
Multi-1/LPCI VA2 c. Slew: Slew Rate Limit Ability 10M: Not use Slew Rate Limit ability. Maximum communication speed 921.6Kbps in this mode. 250K: Use Slew Rate Limit ability. Communication speed is limited under 250Kbps. Slew Rate Limit reduces reflected waves emitting from ends of communication cables and speeds up slew-rate driver that restrains EMP electromagnetic waves thereby enabling communication with no data errors. But communication speed is limited in this mode. 3.
Multi-1/LPCI VA2 5.
Multi-1/LPCI VA3 Multi-1/LPCI VA3 Multi-1/LPCI VA3 board is a model that supports PCI Local Bus Spec 2.3. It is an asynchronous single port product designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-1/LPCI VA3 uses SB16C1050 core designed by SystemBase. Multi-1/LPCI VA3 not only supports maximum communication speed of 921.6Kbps but also provides advanced ability of HW Auto Flow control and 256byte FIFO.
Multi-1/LPCI VA3 - RS232, Combo Common Combo refers to products that can alternatively use RS422 or RS485 using jumper settings 1. Port1: External Power Supply Setting Jumper RI: Do not supply external power and use pin 9 for RI signal line. +5V: Use pin 9 for supplying +5V external power. +12V: Use pin 9 for supplying +12V external power. In case you want to supply +5V power but the PCI slot does not supply it, you should use PC’s power supply.
Multi-1/LPCI VA3 - RS232 Model 1. 9 Pin Connector (Male) 2. Connecting Terminal 3.
Multi-1/LPCI VA3 - RS422/RS485 Combo Model Combo refers to products that can alternatively use RS422 or RS485 using jumper settings 1. 9 Pin Connector (Male) 2. Jumper Settings a. Interface Settings: Interface Selection 422: Select RS422 Interface 485: Select RS485 Interface b.
Multi-1/LPCI VA3 c. Slew: Slew Rate Limit Ability 10M: Not use Slew Rate Limit ability. Maximum communication speed 921.6Kbps in this mode. 250K: Use Slew Rate Limit ability. Communication speed is limited under 250Kbps. Slew Rate Limit reduces reflected waves emitting from ends of communication cables and speeds up slew-rate driver that restrains EMP electromagnetic waves thereby enabling communication with no data errors. But communication speed is limited in this mode. 3.
Multi-1/LPCI VA3 5.
Multi-2/PCI VA1 Multi-2/PCI VA1 Multi-2/PCI VA1 board is a model that supports PCI Local Bus Spec 2.3. It is a asynchronous 2 port product designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-2/PCI VA1 uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-2/PCI VA1 not only supports maximum communication speed of 921.
Multi-2/PCI - RS232 Model 1. 9 Pin Connector (Male) 2. Connecting Terminal 3.
Multi-2/PCI VA1 - RS422 Model 1. 9 Pin Connector (Male) 2. Mode Change Select between point-to-point mode and multi-drop mode during the installation of the device driver. The default mode is point-to-point mode. 3. Connecting External Point-to-Point 4.
Multi-2/PCI - RS485 Model 1. 9 Pin Connector (Male) 2. Mode Change Select between non-echo mode and echo mode during the installation of the device driver. The default mode is non-echo mode. 3.
Multi-2/PCI VA2 Multi-2/PCI VA2 Multi-2/PCI VA2 board is a model that supports PCI Local Bus Spec 2.3. It is an asynchronous 2 port product designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-2/PCI VA2 uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-2/PCI VA2 not only supports maximum communication speed of 921.
Multi-2/PCI VA2 - RS232 Model 1. 9 Pin Connector (Male) 2. Connecting Terminal 3.
Multi-2/PCI VA2 - RS422/RS485 Combo Model Combo refers to products that can alternatively use RS422 or RS485 using jumper settings. 1. DB9 Connector (Male) 2. Jumper Settings a. Interface Settings: Interface Selection 422: Select RS422 Interface 485: Select RS485 Interface b.
Multi-2/PCI VA2 c. Slew: Slew Rate Limit Ability 10M: Not use Slew Rate Limit ability. Maximum communication speed 921.6Kbps in this mode. 250K: Use Slew Rate Limit ability. Communication speed is limited under 250Kbps. Slew Rate Limit reduces reflected waves emitting from ends of communication cables and speeds up slew-rate driver that restrains EMP electromagnetic waves thereby enabling communication with no data errors. But communication speed is limited in this mode.
Multi-2/PCI VA3 Multi-2/PCI VA3 Multi-2/PCI VA3 board is a model that supports PCI Local Bus Spec 2.3. It is an asynchronous single port product designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-2/PCI VA3 uses SB16C1050 core designed by SystemBase. Multi-2/PCI VA3 not only supports maximum communication speed of 921.6Kbps but also provides advanced ability of HW Auto Flow control and 256byte FIFO.
Multi-2/PCI VA3 - RS232 Model 1. 9 Pin Connector (Male) 2. Connecting Terminal 3.
Multi-2/PCI VA3 - RS422/RS485 Combo Model Combo refers to products that can alternatively use RS422 or RS485 using jumper settings. 1. DB9 Connector (Male) 2. Jumper Settings a. Interface Settings: Interface Selection 422: Select RS422 Interface 485: Select RS485 Interface b.
Multi-2/PCI VA3 c. Slew: Slew Rate Limit Ability 10M: Not use Slew Rate Limit ability. Maximum communication speed 921.6Kbps in this mode. 250K: Use Slew Rate Limit ability. Communication speed is limited under 250Kbps. Slew Rate Limit reduces reflected waves emitting from ends of communication cables and speeds up slew-rate driver that restrains EMP electromagnetic waves thereby enabling communication with no data errors.
Multi-2C/LPCI VA2 Multi-2C/LPCI VA2 Multi-2C/LPCI VA2 board is a model that supports PCI Local Bus Spec 2.3. It is an asynchronous 2 port product designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-2C/LPCI VA2 uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-2C/LPCI VA2 board provides RS232 line interface and maximum communication speed of 921.6Kbps.
Multi-2C/LPCI VA2 - RS232 Model 1. 9 Pin Connector (Male) 2. Connecting Terminal 3.
Multi-2C/LPCI VA2 4. Portx: External Power Supply Setting Jumper RI: Do not supply external power and use pin 9 for RI signal line. +5V: Use pin 9 for supplying +5V external power. +12V: Use pin 9 for supplying +12V external power. In case you want to supply +5V power but the PCI slot does not supply it, you should use PC’s power supply.
Multi-2C/LPCI VA3 Multi-2C/LPCI VA3 Multi-2C/LPCI VA3 board is a model that supports PCI Local Bus Spec 2.3. It is an asynchronous 2 port product designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-2C/LPCI VA3 uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-2C/LPCI VA3 board provides RS232 line interface and maximum communication speed of 921.6Kbps.
Multi-2C/LPCI VA3 - RS232 Model 1. 9 Pin Connector (Male) 2. Connecting Terminal 3.
Multi-2C/LPCI VA3 4. Portx: External Power Supply Setting Jumper RI: Do not supply external power and use pin 9 for RI signal line. +5V: Use pin 9 for supplying +5V external power. +12V: Use pin 9 for supplying +12V external power. In case you want to supply +5V power but the PCI slot does not supply it, you should use PC’s power supply.
Multi-2C/LPCI VA3 - RS422/RS485 Combo Model Combo refers to products that can alternatively use RS422 or RS485 using jumper settings. 1. DB9 Female Connector (Male) 2. Jumper Setting a.
Multi-2C/LPCI VA3 b.
Multi-2C/LPCI VA3 c. Slew: Slew Rate Limit Ability 10M: Not use Slew Rate Limit ability. Maximum communication speed 921.6Kbps in this mode. 250K: Use Slew Rate Limit ability. Communication speed is limited under 250Kbps. Slew Rate Limit reduces reflected waves emitting from ends of communication cables and speeds up slew-rate driver that restrains EMP electromagnetic waves thereby enabling communication with no data errors. But communication speed is limited in this mode 3.
Multi-2C/LPCI VA3 4. RS422 Multi-Drop Connection 5.
Multi-4/LPCI VA1 Multi-4/LPCI VA1 Multi-4/PCI VA1 board is a model that supports PCI Local Bus Spec 2.3. It is an asynchronous 4 port product designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-4/PCI VA1uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-4/LPCI VA1 not only supports maximum communication speed of 921.
Multi-4/LPCI VA1 - RS232 Model 1. 25 Pin Connector (Female) 2. Connecting Terminal 3.
Multi-4/LPCI VA1 - RS422 Model 1. 25 Pin Connector (Female) 2. Mode Change Select between point-to-point mode and multi-drop mode during the installation of the device driver. The default is point-to-point. 3. Connecting External point-to-point 4.
Multi-4/LPCI VA1 -RS485 Model 1. 25Pin Connector (Female) 2. Mode Change Select between non-echo mode and echo mode during the installation of the device driver. The default is non-echo mode. 3. Connection RT: 120 ohm (If there is no serious noise, termination resistors are not required) RS485, like LAN, adopts a half duplex bus where the host is not divided from terminals.
Multi-4/LPCI VA2 Multi-4/LPCI VA2 Multi-4/LPCI VA2 board is a model that supports PCI Local Bus Spec 2.3. It is designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-4/LPCI VA2 uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-4/LPCI VA2 is used with Panel-4 VA2 panel. It not only supports maximum communication speed of 921.
Multi-4/LPCI VA2 - RS232 Model 1. 25 Pin Connector (Male) 2. Connecting Terminal 3.
Multi-4/LPCI VA2 - RS422/RS485 Combo Model Combo refers to products that can alternatively use RS422 or RS485 using jumper settings. 1. DB9 Connector (Female) 2.
Multi-4/LPCI VA2 3. Jumper Settings a. Portx RT: RS422/RS485 Terminal Resistance Selection (Port 1 is Port #1, Port2 is Port#2) 422: Set RS422 Terminal Resistor 485: Set RS485 Terminal Resistor None: Do not set Terminal Resistor b. Slew: Slew Rate Limit Ability 10M: Not use Slew Rate Limit ability. Maximum communication speed 921.6Kbps in this mode. 250K: Use Slew Rate Limit ability. Communication speed is limited under 250Kbps.
Multi-4/LPCI VA2 4. RS422 Point-to-Point Connection 5. RS422 Multi-Drop Connection 6.
Multi-4/LPCI VA3 Multi-4/LPCI VA3 Multi-4/LPCI VA3 board is a model that supports PCI Local Bus Spec 2.3. It is designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-4/LPCI VA3 uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-4/LPCI VA3 is used with Panel-4 VA2 panel. It not only supports maximum communication speed of 921.
Multi-4/LPCI VA3 - RS232/Combo Common 1. Portx: External Power Supply Setting Jumper PORT1 is Port #1, PORT2 is Port #2 67 RI: Do not supply external power and use pin 9 for RI signal line. +5V: Use pin 9 for supplying +5V external power. +12V: Use pin 9 for supplying +12V external power.
Multi-4/LPCI VA3 - RS232 Model 1. 25 Pin Connector (Male) 2. Connecting Terminal 3.
Multi-4/LPCI VA3 - RS422/RS485 Combo Model Combo refers to products that can alternatively use RS422 or RS485 using jumper settings. 1. DB9 Connector (Female) 2.
Multi-4/LPCI VA3 3. Jumper Settings a.
Multi-4/LPCI VA3 b. Slew: Slew Rate Limit Ability 10M: Not use Slew Rate Limit ability. Maximum communication speed 921.6Kbps in this mode. 250K: Use Slew Rate Limit ability. Communication speed is limited under 250Kbps. Slew Rate Limit reduces reflected waves emitting from ends of communication cables and speeds up slew-rate driver that restrains EMP electromagnetic waves thereby enabling communication with no data errors. But communication speed is limited in this mode 4.
Multi-4/LPCI VA3 5. RS422 Multi-Drop Connection 6.
Multi-4C/PCI VA2 Multi-4C/PCI VA2 Multi-4C/PCI VA2 board is a model that supports PCI Local Bus Spec 2.3. It is designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-4C/PCI VA2 uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-4C/PCI VA2 not only supports maximum communication speed of 921.
Multi-4C/PCI VA2 - RS232 Model 1. 9 Pin Connector (Male) 2. Connecting Terminal 3.
Multi-4C/PCI VA2 4. PORTx PWR: voltage supply selection jumper (PORT1 is Port #1~ PORT4 is Port #4) 75 +5V: supply 5V voltage to peripheral using 9th.pin. +12V: supply 12V voltage to peripheral using 9th.pin. RI: Enables RI communication when using RS232. not supply any peripheral.
Multi-4C/PCI VA2 If there is no 5V voltage in PCI slot of user’s PC, should be supplied by Power Supply of PC.
Multi-4C/PCI VA3 Multi-4C/PCI VA3 Multi-4C/PCI VA3 board is a model that supports PCI Local Bus Spec 2.3. It is designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Multi-4C/PCI VA3 not only supports maximum communication speed of 921.6Kbps but also provides advanced ability to automatically control IO signals when it is used with driver provided by SystemBase. And It has 256 Byte FIFO, so that more stable.
Multi-4C/PCI VA3 - RS232 Model 1. 9 Pin Connector (Male) 2. Connecting Terminal 3.
Multi-4C/PCI VA3 4. PORTx PWR: voltage supply selection jumper (PORT1 is Port #1~ PORT4 is Port #4) +5V: supply 5V voltage to peripheral using 9th.pin. +12V: supply 12V voltage to peripheral using 9th.pin. RI: Enables RI communication when using RS232. not supply any peripheral.
Multi-4C/PCI VA3 If there is no 5V voltage in PCI slot of user’s PC, should be supplied by Power Supply of PC. * Warning: When a jumper is set to +5V or +12V, it is necessary to make sure that a device that a jumper connects has the same setting as the jumper. Since power is supplied through pin 9, a device may break down when this requirement is not met.
Multi-4C/PCI VA3 - RS422/RS485 Combo Model Combo refers to products that can alternatively use RS422 or RS485 using jumper settings. 1. DB9 Connector (Female) 2. Interface Settings Selects RS422, RS485 line interface and mode 422: If you want RS422, set jumper like this.
Multi-4C/PCI VA3 3. Jumper Settings a. Portx RT: RS422/RS485 Terminal Resistance Selection (Port 1 is Port #1, Port2 is Port#2) 422: Set RS422 Terminal Resistor 485: Set RS485 Terminal Resistor None: Do not set Terminal Resistor b.
Multi-4C/PCI VA3 10M: Not use Slew Rate Limit ability. Maximum communication speed 921.6Kbps in this mode. 250K: Use Slew Rate Limit ability. Communication speed is limited under 250Kbps. Slew Rate Limit reduces reflected waves emitting from ends of communication cables and speeds up slew-rate driver that restrains EMP electromagnetic waves thereby enabling communication with no data errors. But communication speed is limited in this mode 4. RS422 Point-to-Point Connection 5.
Multi-4C/PCI VA3 RT: 120 Ohm (Not necessary when there is not much noise) RS485, like LAN, uses Half Duplex Bus and has no classification between host and terminal 84
Multi-4J/PCI VA1 Multi-4J/PCI VA1 Multi-4J/PCI VA1 board is a model that supports PCI Local Bus Spec 2.3. It is designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-4J/PCI VA1 uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-4J/PCI VA1 not only supports maximum communication speed of 921.
Multi-4J/PCI VA1 - RS232 Model 1. RJ45 JACK & 25 Pin Connector (MALE, Extension Cable) 2. Connecting Terminal 3.
Multi-4J/PCI VA1 - RS422 Model 1. RJ45 Jack & 25 Pin Connector (MALE, Extension Cable) 2. Mode Change Select between point-to-point mode and multi-drop mode during the installation of the device driver. The default is mode point-to-point mode. 3 Connecting External point-to-point 4.
Multi-4J/PCI VA1 - RS485 Model 1. RJ45 Jack & 25 Pin Connector (Male, Extension Cable) 2. Mode Change Select between non-echo mode and echo mode during the installation of the device driver. The default is non-echo mode. 3. Connection RT: 120 Ohm(If there is no serious noise, termination resistors are not required) RS485, like LAN, adopts a half duplex bus where the host is not divided from terminals.
Multi-4J/PCI VA2 Multi-4J/PCI VA2 Multi-4J/PCI VA2 board is a model that supports PCI Local Bus Spec 2.3. It is designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-4J/PCI VA2 uses core for PCI Local Bus Spec 2.3 designed by SystemBase and can be used on PCI 3.3V bus system. Multi-4J/PCI VA2 not only supports maximum communication speed of 921.
Multi-4J/PCI VA2 -RS232, Combo Common 1. Portx: External Power Supply Setting Jumper PORT1 is Port #1, PORT2 is Port #2 RI: Do not supply external power and use pin 9 for RI signal line. +5V: Use pin 9 for supplying +5V external power. +12V: Use pin 9 for supplying +12V external power. In case you want to supply +5V power but the PCI slot does not supply it, you should use PC’s power supply.
Multi-4J/PCI VA2 - RS232 Model 1. DB9 Connector (Male), RJ45 Connector 2. Connecting Terminal 3.
Multi-4J/PCI VA2 - RS422/RS485 Combo Model Combo refers to products that can alternatively use RS422 or RS485 using jumper settings. 1. DB9 Connector (Male), RJ45 Connector 2. Jumper Settings a. Interface Settings: Interface Selection 422: Select RS422 Interface 485: Select RS485 Interface b.
Multi-4J/PCI VA2 c. Slew: Slew Rate Limit Ability 10M: Not use Slew Rate Limit ability. Maximum communication speed 921.6Kbps in this mode. 250K: Use Slew Rate Limit ability. Communication speed is limited under 250Kbps. Slew Rate Limit reduces reflected waves emitting from ends of communication cables and speeds up slew-rate driver that restrains EMP electromagnetic waves thereby enabling communication with no data errors. But communication speed is limited in this mode 3.
Multi-4J/PCI VA2 5.
Multi-4JALL+/PCI VA2 Multi-4JALL+/PCI VA2 Multi-4JALL/PCI VA2 board is a model that supports PCI Local Bus Spec 2.3. It is designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-4JALL+/PCI VA2 uses core for PCI Local Bus Spec 2.3 designed by SystemBase and can be used on PCI 5V and PCI 3.3V bus system. Multi-4 JALL+/PCI VA2 not only supports maximum communication speed of 921.
Multi-4JALL+/PCI VA2 - Connection Pin arrangement of Multi-4JALL+ product is different for pin arrangement of Multi-4J product. So, you should not use Multi-4JALL+ cable mixed with Multi-4J. Please be careful this thing. 1. RJ45 Jack 2. 9 Pin Connector (Male, Expandable Cable) 3.
Multi-4JALL+/PCI VA2 4.
Multi-4JALL+/PCI VA2 - Switch and Jumper Names 1. Port configuration switch 2. External device power supply configuration switch 3.
Multi-4JALL+/PCI VA2 - Configuration of DIP SW when setting serial interface ON 1 2 3 4 5 6 RS232 ON ON 1 2 3 4 5 6 1 Point to Point Mode 2 3 4 5 6 Multi Drop Mode RS422 ON ON 1 2 3 4 5 6 1 Non Echo Mode 2 3 4 5 6 Echo Mode RS485 - Configuration of the RS422/RS485 Slew-Rate Limit Ability’s DIP SW 1. When setting RS422/RS485 Slew-Rate Limit function ON 1 2 3 4 5 6 Some RS422/RS485 transceivers are equipped with Slew-Rate Limit ability.
Multi-4JALL+/PCI VA2 2. When not setting the RS422/RS485 Slew-Rate Limit ON 1 2 3 4 5 6 Initial condition used when opposing RS422/RS485 transceiver does not have the Slew-Rate Limit function. When the Slew-Rate Limit function is not selected maximum communication speed is 921.6Kbps. (Max chip speed: 16Mbps) - Configuration of the Terminal Resistor’s DIP SW 1. When setting RS422 Terminal resistor ON 1 2 3 4 5 6 2.
Multi-4JA/PCI Multi-4JA/PCI Multi-4JA/PCI board is a model that supports PCI Local Bus Spec 2.3. It is designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-4JA/PCI uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-4 JA/PCI not only supports maximum communication speed of 921.6Kbps but also provides advanced ability to automatically control IO signals when it is used with driver provided by SystemBase.
Multi-4JA/PCI - RS232 Model 1. RS232 Jumper Setting 2. RJ45 JACK & 9 Pin Connector (MALE, Extension Cable) 3. Connecting Terminal 4.
Multi-4JA/PCI - RS422 Model 1. RS422 Jumper Setting 2. RJ45 JACK (*Not providing RS422 DB-type cable separately) 3. Mode Change Select between point-to-point mode and multi-drop mode during the installation of the device driver. The default is point-to-point mode. 4.
Multi-4JA/PCI 5.
Multi-4JA/PCI - RS485 Model 1. RS485 Jumper Setting 2. RJ45 JACK (*Not providing RS485 DB-type cable separately) 3. Mode Change Select between non-echo mode and echo mode during the installation of the device driver. The default is non-echo mode. 4.
Multi-4JA/PCI - Setting RS422/RS485 Termination Resistors The termination resistors are connected only to channels located at the last end based on RS422 or RS485 transmission mode. Multi-4JA is available for independent connection to termination resistors by using DIP switch on each channel. At this time, be sure to turn “on” the DIP switch on the channel.
Multi-4JALL+/ISO Multi-4JALL+/ISO Multi-4JALL+/ISO board is a model that supports PCI Local Bus Spec 2.3. It is an asynchronous 4 port product designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-4JALL/PCI VA2 uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-4 JALL/PCI VA2 not only supports maximum communication speed of 921.
Multi-4JALL+/ISO - Connecting Connectors 1. RJ45 Jack 2. 9 Pin Connector (Male, Expandable Cable) 3. Connecting Terminal 4.
Multi-4JALL+/ISO - Setting up the DIP SW - Configuration of DIP SW when setting serial interface 1. RS232 ON 1 2 3 4 5 6 2. RS422 ON ON 1 2 3 4 5 6 Point to Point Mode 1 2 3 4 5 6 Multi Drop Mode 3.
Multi-4JALL+/ISO - Configuration of the RS422/RS485 Slew-Rate Limit Ability’s DIP SW 1. When setting RS422/RS485 Slew-Rate Limit function ON 1 2 3 4 5 6 Some RS422/RS485 transceivers are equipped with Slew-Rate Limit ability. In order to maintain compatibility with these chips, the Slew-Rate Limit ability must be activated. If Slew Rate Limit function is activated, communication speed considerably decreases but instead gives off less emission.
Multi-4ALL/cPCI Multi-4ALL/cPCI Multi-4ALL/cPCI is an asynchronous 4 port product designed to be equipped on Compact PCI System. It provides maximum communication speed of 921.6Kbps and different line interface RS232/RS422/RS484 for each port. Furthermore, it is equipped with surge protector to protect internal systems from outer shock. - Product Specifications Communication Speed Maximum 921.
Multi-4ALL/cPCI - RS232 Model 1. RS232 Jumper Setting 2. 9 Pin Connector (Female) 3.
Multi-4ALL/cPCI - RS422 Model 1. RS422 Jumper Setting 2. 9 Pin Connector (Female) 3. Mode Change Either Point-to-Point or Multi-Drop mode can be selected by software on device driver installation. Point-to-Point mode is set to default. 4.
Multi-4ALL/cPCI 5.
Multi-4ALL/cPCI -RS485 Model 1. RS485 Jumper Setting 2. 9Pin Connector (Female) 3. Switching Modes Either Point-to-Point or Multi-Drop mode can be selected by software on device driver installation. Point-to-Point mode is set to default. 4.
Multi-4ALL/cPCI -Terminal Resistor Setting Terminal Resistor only connects to channels in terminals in RS422/RS485 mode. Multi4ALL/cPCI can independently connect to all terminal resistors using jumpers for all channels. To connect to terminal resistors, Turn ON following jumpers.
Multi-8/LPCI VA1 Multi-8/LPCI VA1 Multi-8/LPCI VA1 board is a model that supports PCI Local Bus Spec 2.3. It is designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts.. Unlike former products, Multi-8/LPCI VA1 uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-8/LPCI VA1 not only supports maximum communication speed of 921.
Multi-8/LPCI VA1 - RS232 Model 1. 9 Pin, 25 Pin Connector (Female) 2. Connecting Terminal 3.
Multi-8/LPCI VA1 - RS422 Model 1. 25 Pin Connector (Female) 2. Mode Change Select between point-to-point mode and multi-drop mode during the installation of the device driver. The default is point-to-point mode. 3. Connecting External point-to-point 4.
Multi-8/LPCI VA1 - RS485 Model 1. 25 Pin Connector (Female) 2. Mode Change Select between non-echo mode and echo mode during the installation of the device driver. The default is non-echo mode. 3. Connection RT: 120 Ohm(If there is no serious noise, termination resistors are not required) RS485, like LAN, adopts a half duplex bus where the host is not divided from terminals.
Multi-8/LPCI VA2 Multi-8/LPCI VA2 Multi-8/LPCI VA2 board is a model that supports PCI Local Bus Spec 2.3. It is designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-8/LPCI VA2 uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-8/LPCI VA2 is used with Panel-8 VA2. It not only supports maximum communication speed of 921.
Multi-8/LPCI VA2 -RS232 Model 1. DB9 Connector (Female) 2. Connecting Terminal 3.
Multi-8/LPCI VA2 - RS422/RS485 Combo Model Combo refers to products that can alternatively use RS422 or RS485 using jumper settings. 1. DB9 Connector (Female) 2.
Multi-8/LPCI VA2 3. Jumper Settings a. Portx RT: RS422/RS485 Terminal Resistance Selection (Port 1 is Port #1, Port2 is Port#2) 422: Set RS422 Terminal Resistor 485: Set RS485 Terminal Resistor None: Do not set Terminal Resistor b. Slew: Slew Rate Limit Ability 10M: Not use Slew Rate Limit ability. Maximum communication speed 921.6Kbps in this mode. 250K: Use Slew Rate Limit ability. Communication speed is limited under 250Kbps.
Multi-8/LPCI VA2 4. RS422 Point-to-Point Connection 5. RS422 Multi-Drop Connection 6.
Multi-8/LPCI VA3 Multi-8/LPCI VA3 Multi-8/LPCI VA3 board is a model that supports PCI Local Bus Spec 2.3. It is designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-8/LPCI VA3 uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-8/LPCI VA3 is used with Panel-8 VA2. It not only supports maximum communication speed of 921.
Multi-8/LPCI VA3 -RS232, Combo Common 1. Portx: External Power Supply Setting Jumper PORT1 is Port #1, PORT2 is Port #2 127 RI: Do not supply external power and use pin 9 for RI signal line. +5V: Use pin 9 for supplying +5V external power. +12V: Use pin 9 for supplying +12V external power.
Multi-8/LPCI VA3 -RS232 Model 1. DB9 Connector (Female) 2. Connecting Terminal 3.
Multi-8/LPCI VA3 - RS422/RS485 Combo Model Combo refers to products that can alternatively use RS422 or RS485 using jumper settings. 1. DB9 Connector (Female) 2.
Multi-8/LPCI VA3 3. Jumper Settings a. Portx RT: RS422/RS485 Terminal Resistance Selection (Port 1 is Port #1, Port2 is Port#2) 422: Set RS422 Terminal Resistor 485: Set RS485 Terminal Resistor None: Do not set Terminal Resistor b. Slew: Slew Rate Limit Ability 10M: Not use Slew Rate Limit ability. Maximum communication speed 921.6Kbps in this mode. 250K: Use Slew Rate Limit ability. Communication speed is limited under 250Kbps.
Multi-8/LPCI VA3 4. RS422 Point-to-Point Connection 5. RS422 Multi-Drop Connection 6.
Multi-8C/PCI VA2 Multi-8C/PCI VA2 Multi-8C/PCI VA2 board is a model that supports PCI Local Bus Spec 2.3. It is designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-8C/PCI uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-8C/PC VA2I not only supports maximum communication speed of 921.6Kbps but also provides advanced ability to automatically control IO signals when it is used with driver provided by SystemBase.
Multi-8C/PCI VA2 - RS232 Model 1. 9 Pin Connector (Male) 2. Connecting Terminal 3.
Multi-8C/PCI VA3 Multi-8C/PCI VA3 Multi-8C/PCI VA3 board is a model that supports PCI Local Bus Spec 2.3. It is designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Multi-8C/PCI VA3 not only supports maximum communication speed of 921.6Kbps but also provides advanced ability to automatically control IO signals when it is used with driver provided by SystemBase. And It has 256 Byte FIFO, so that more stable.
Multi-8C/PCI VA3 - RS232 Model 1. 9 Pin Connector (Male) 2. Connecting Terminal 3.
Multi-8C/PCI VA3 - RS422/485 Combo Model Combo refers to products that can alternatively use RS422 or RS485 using jumper settings. 1. DB9 Connector (Female) 2. Interface Settings Selects RS422, RS485 line interface and mode 422: If you want RS422, set jumper like this.
Multi-8C/PCI VA3 3. Jumper Settings a.
Multi-8C/PCI VA3 b. Slew: Slew Rate Limit Ability 10M: Not use Slew Rate Limit ability. Maximum communication speed 921.6Kbps in this mode. 250K: Use Slew Rate Limit ability. Communication speed is limited under 250Kbps. Slew Rate Limit reduces reflected waves emitting from ends of communication cables and speeds up slew-rate driver that restrains EMP electromagnetic waves thereby enabling communication with no data errors. But communication speed is limited in this mode 4.
Multi-8C/PCI VA3 5. RS422 Multi-Drop Connection 6.
Multi-16C/PCI VA1 Multi-16C/PCI VA1 Multi-16C/PCI VA1 board is a model that supports PCI Local Bus Spec 2.3. It is an asynchronous 16 port product designed to automatically set I/O address and IRQ number when ROM bios or the operating system starts. Unlike former products, Multi-16C/PCI VA1 uses core for PCI Local Bus Spec 2.3 designed by SystemBase. Multi-16C/PCI VA1 board supports RS232 line interface and maximum communication speed of 921.6Kbps.
Multi-16C/PCI - RS232 Connector 1. 78Pin Connector (Female) 141 Multi-16C/PCI only supports TXD, RXD, RTS, CTS signal lines.
Multi-32/LPCI VA1 Multi-32/LPCI VA1 Multi-32/LPCI VA1 is a model that supports PCI Local Bus Spec 2.3, which is designed to set up I/O address and IRQ number automatically upon starting ROM BIOS and Operating System without DIP switch to board. In the Multi-32/LPCI VA1, 32 ports only occupy 64 bytes of small I/O space and there is no limitation of number to be installed as long as slots are available, which solves a problem of Multi-32/PCI VA1 as it was limited to install maximum 4 units.
Multi-32/LPCI VA1 - RS232 Model 1. 9 Pin, 25 Pin Connector (Female) 2. Connecting Terminal 3.
Multi-32/LPCI VA1 - RS422 Model 1. 25 Pin Connector (Female) 2. Mode Change Select between point-to-point mode and multi-drop mode during the installation of the device driver. The default is point-to-point mode. 3. Connecting External point-to-point 4.
Multi-32/LPCI VA1 - RS485 Model 1. 25 Pin Connector (Female) 2. Mode Change Select between non-echo mode and echo mode during the installation of the device driver. The default is non-echo mode. 3. Connection 145 RT: 120ohm (if there is no serious noise, termination resistors are not required) RS485, like, adopts a half duplex bus where the host is not divided from terminals.
Multi-32/LPCI VA2 Multi-32/LPCI VA2 Multi-32/LPCI VA2 board is the model supports PCI Local Bus Spec 2.3. It has 32 Ports that can set I/O address and IRQ number automatically. Unlike existing products, VA2 applies PCI Local Bus Spec 2.3 Core which was developed by SystemBase. Multi-32/LPCI VA2 board is used with Panel-8e VA2. It not only supports maximum speed of 921.6Kbps but also offers enhanced management of automatic I/O.
Multi-32/LPCI VA2 -RS232 Model 1. DB9 Connector (Female) 2. Connecting Terminal 3.
Multi-32/LPCI VA2 - RS422/RS485 Combo model What is combo in this case? : The products that can be selected in RS422, 485 by jumper setting 1. DB9 Female connector pin specification 2. Panel switch setting a.
Multi-32/LPCI VA2 b. PORTx SLEW: Slew Rate Limit function fit jumper PORT1 is 1st port, PORT2is 2st port 10M: Not use Slew Rate Limit ability. Maximum communication speed 921.6Kbps in this mode. 250K: Use Slew Rate Limit ability. Communication speed is limited under 250Kbps. Slew Rate Limit reduces reflected waves emitting from ends of communication cables and speeds up slew-rate driver that restrains EMP electromagnetic waves thereby enabling communication with no data errors.
Multi-32/LPCI VA2 c. PORTx RT : RS422, RS485 terminal resister select jumper PORT 1 is first port, PORT2 is second port 422: Install RS422 terminal resister. 485: Install RS485 terminal resister. NONE: Not install terminal resister. 3.
Multi-32/LPCI VA2 4. RS422 Multi-drop Connection 5. RS485 Connection RT: 120 ohm(If there is no serious noise, termination resistors are not required) RS485, like LAN, adopts a half duplex bus where the host is not divided from terminals.
Multi-32/LPCI VA3 Multi-32/LPCI VA3 Multi-32/LPCI VA3 board is the model supports PCI Local Bus Spec 2.3. It has 32 Ports that can set I/O address and IRQ number automatically. In addition, unlike existing products, VA3 applies PCI Local Bus Spec 2.3 Core which was developed by SystemBase. Multi-32/LPCI VA3 board is used with Panel-8e VA2 or Panel-8e VA3. It not only supports maximum speed of 921.6Kbps but also offers enhanced management of automatic I/O.
Multi-32/LPCI VA3 - RS232 model 1. DB9 Connector 2. Connecting Terminal 3.
Multi-32/LPCI VA3 4. External Power Supply In case you want to supply +5V power, you should use PC’s power supply. +5V: supply 5V voltage to peripheral. +12V: supply 12V voltage to peripheral. RI: Enables RI communication when using RS232.
Multi-32/LPCI VA3 - RS422/RS485 Combo model What is combo in this case? : The products that can be selected in RS422, 485 by jumper setting 1. DB9 Female, Male connector pin specification 2. Panel switch setting a.
Multi-32/LPCI VA3 b. PORTx RT : RS422, RS485 terminal resister selection jumper 10M: Not use Slew Rate Limit function. Maximum communication speed 921.6Kbps in this mode. 250K: Use Slew Rate Limit function. Communication speed is limited under 250Kbps. Slew Rate Limit reduces reflected waves emitting from ends of communication cables and speeds up slew-rate driver that restrains EMP electromagnetic waves thereby enabling communication with no data errors.
Multi-32/LPCI VA3 c. PORTx RT : RS422, RS485 terminal resister selecting jumper 422: Install RS422 terminal resister. 485: Install RS485 terminal resister. NONE: Not install terminal resister. ※ What is terminal resister? Transmission interface has several design impedance standards. So when that comes up to this specific resister, we need terminal resister in order to avoid reflection phenomenon.
Multi-32/LPCI VA3 3. RS422 Point-to-point Connection 4. RS422 Multi-drop Connection 5. RS485 Connection RT: 120 ohm(If there is no serious noise, termination resistors are not required) RS485, like LAN, adopts a half duplex bus where the host is not divided from terminals.
Panel Compatibility Table Panel Compatibility Table Panel-4 Board Multi-4 Panel VA1 VA2 VA3 LPCI VA1 O X - LPCI VA2 X O - LPIC VA3 X O - Panel-8 Board Multi-8 Panel VA1 VA2 VA3 LPCI VA1 O X - LPCI VA2 X O - LPCI VA3 X O - Panel-8E Board Multi-32 159 Panel VA1 VA2 VA3 LPCI VA1 O X X LPCI VA2 X O O LPCI VA3 X O O
Power Consumption Power Consumption Power Type Product Name Consumption (W) Voltage Current (V) (A) Multi-1/LPCI RS232 1.6401 3.3 0.497 Multi-1/LPCI COMBO 1.6071 3.3 0.487 Multi-2/PCI RS232 1.8381 3.3 0.557 Multi-2/PCI COMBO 1.7721 3.3 0.537 VA3 PCI Multi-4/LPCI RS232 4.5012 3.3 1.364 MultiPort Multi-4/LPCI COMBO 4.3692 3.3 1.324 Multi-8/LPCI RS232 5.8971 3.3 1.787 Multi-8/LPCI COMBO 5.6331 3.3 1.707 Multi-32/LPCI RS232 25.9479 3.3 7.
