Operating Instructions and Installation Instructions

– 8
t
Safety instructions
ATTENTION!
Important instructions for safe installation. Observe all
installation instructions – improper installation can lead to
serious injuries!
ATTENTION!
After installation, it is imperative that you check the drive to
ensure that it has been correctly adjusted and that it reverses
upon contacting a 50 mm high object on the oor.
¾ The drive may only be installed, connected and commissioned by
qualied technicians.
¾ Do not move the gate if there are people, animals or objects in the area
of movement.
¾ Keep children, disabled persons and animals away from the door.
¾ Wear safety glasses when drilling the fastening holes.
¾ Cover the drive during drilling to prevent penetration of dirt.
ATTENTION!
Walls and ceiling must be solid and stable. Only install the
drive on a correctly aligned door. An incorrectly aligned door
could cause serious injury.
¾ Doors must be stable in themselves, since high traction and
compression forces are encountered. Reinforce lighter doors made of
plastic or aluminum if necessary before installation. Ask a specialist
retailer for advice.
¾ Remove or disable door locks.
¾ Use only approved fasteners (e.g. anchor ttings, bolts). The fasteners
must be suitable to the material of the ceilings and walls.
¾ Check that the door runs smoothly.
¾ The door must be counterbalanced.
TEST:
Half-open the door by hand. The door must remain in this
position. If the door moves up or down, re-adjust the door
mechanically. Ask a specialist retailer for advice.
Check the distance between the door's highest point (THP, see graphic 11)
and the ceiling. The distance between the THP and the lower edge C must
be between 5 mm and 65 mm; the angle of the door arm must be max. 30°
(see graphic 11). If the distance is less than this, the drive must be moved
back and a longer push rod must be installed. Ask a specialist retailer for
advice.
Door types and accessories*
* Accessories not included in the scope of delivery
12 3
45
No. Door type Accessories
Swinging door No accessories required
Sectional door with single
running rail
Sectional door tting with
boomerang *
Sectional door with double
running rail
Sectional door bracket without
boomerang
Sectional overhead door No accessories required
Up-and-over door Curved arm *
Hinged double door Hinged double door tting *
Roller door, side-sectional door Consult your specialist dealer
Tips for installation
• Check the delivery scope components before beginning installation;
this way you save time and unnecessary effort if a part is missing.
• With two persons, installation can be carried out quickly and safely.
• Ensure that the door does not become twisted or jammed in the running
rails.
CHECK:
Open and close the door by hand several times at the location
where the drive is to be installed. If the door can be operated
easily at this location (without exceeding the specied
forces), then the drive can be installed.
Emergency release
In a garage without a separate entrance (e.g. slip doors), the drive's
emergency release must be operable from outside. Thus, position the
emergency release so that it externally accessible; this can be done with
a Bowden cable or an emergency release lock. For this purpose, Backjump
(DIP switch 6 ON) should always be switched on. Refer to the chapter
“Functions and connections - Backjump (DIP 6)”.
Swinging doors
Because the mechanical locking of a door equipped with a drive must be
removed or disabled, depending on the design of the door, it could be
possible to manually raise the door approx. 50 mm. To counteract this,
spring catches can installed to lock the door in addition to the drive. These
spring catches are connected to the drive by means of a locking set; when
opening a door, the spring catches must rst be disengaged before the
drive can open the door.
Hinged double door, roller door or side-sectional door
With drives that push one of the previously mentioned doors ahead (see
graphic below), the polarity of wires 3 + 4 must be reversed on the direct
connector. See chapter “Functions and connections - direct connector”.
Installation