User Manual

3
Connecting the System
1. Place the two rock satellites and the rock woofer in their
approximate final locations.
2. Dig a 4” to 5” trench to run the speaker wires in. You
will need to trench from an area nearest your amplifier
to the MR10W woofer and then from the woofer to the
two MR6 satellites. Be sure to check local codes for
trenching limitations.
3. Run the appropriate gauge wire through the trench
from your amplifier to the MR10W woofer. Connect those
wires to the MR10W woofer (See Figure 2.)
4. Connect the wires from the MR6 satellites to the
MR10W woofer (see figure 2.)
5. After making all the connections at the MR10W woofer,
connect the speaker wires to your amplifier.
6. After confirming that you have properly made all of the
connections, turn your amplifier on and test the system
with your favorite music. If the speakers are all operating
properly, refill the wire trenches and using the supplied
screws, attach the wire termination cover plate to the
connector panel on the bottom of the RK10W enclosure.
The cover plate will keep moisture from damaging
the connections.
NOTE: REGARDING THE 4 COLORED DIRECT BURIAL
WIRE, THE RED (+) AND BLACK (-) ARE USED FOR THE
RIGHT CHANNEL, AND THE WHITE (+) AND GREEN (-)
ARE FOR THE LEFT CHANNEL.
IMPORTANT: BE SURE NOT TO LET ANY STRAY (+)
AND (–) WIRES TOUCH EACH OTHER. TOUCHING
WIRES WILL CAUSE A SHORT-CIRCUIT WHICH COULD
DAMAGE YOUR AMPLIFIER.
NOTE: DOUBLE-CHECK THAT YOU HAVE CONNECTED
ALL OF THE WIRES PROPERLY AMPLIFIER (+) TO
SPEAKER (+); AMPLIFIER (–) TO SPEAKER (–) AT
EACH OF THE CONNECTIONS. IT IS CRITICAL THAT
THE POSITIVE AND NEGATIVE WIRES BE CONNECTED
CORRECTLY FOR BOTH CHANNELS. IF EITHER
CHANNEL IS CONNECTED INCORRECTLY LITTLE TO
NO LOW FREQUENCY SOUND WILL BE PRODUCED.
Tweeter:
Woofer:
Frequency Response:
Impedance:
Power Handling:
Sensitivity:
Dimensions (WxHxD):
Shipping Weight
Woofer:
Frequency Response:
Impedance:
Power Handling:
Sensitivity:
Crossover Frequency:
Dimensions (WxHxD):
MAGMR6 SATELLITE ROCK SPEAKERS
MAGROCKS2.1 OUTDOOR ROCK SPEAKER SYSTEM
MAGMR10W ROCK WOOFER
Specifications
1” (25mm) polyurethane dome, ferrofluid-cooled
6 1/2” (162mm) polypropylene cone with a SantopreneTM surround
50Hz – 20 kHz +/- 3dB
8 ohms nominal; 6 ohms minimum
5 watts minimum; 100 watts maximum
89dB SPL (2.83V/1 meter)
11” x 10 1/2” x 14” (279mm x 267mm x 356mm)
67.75 lb. (31 kg)
10” (254mm) Black polypropylene cone, dual voice coil, rubber surround
35Hz – 150Hz +/- 3dB
8 Ohms nominal
5 watts minimum; 150 watts maximum
90dB SPL (2.83V/1 meter)
150 Hz (low-pass); 150Hz (high-pass)
19 3/8” x 16 7/8” 14 3/8” (492mm x 429mm x 365mm)
Specifications subject to change. Direct burial cable required (sold separately). Amplifier (sold separately).
OUTPUT
INPUT
RIGHT
RIGHT
LEFT
LEFT
RED
BLACK
RED
BLACK
WHITE
GREEN
WHITE
GREEN
To Right
Satellite Speaker
To Left
Satellite Speaker
From Amplifier
Right Channel
From Amplifier
Left Channel
Figure 2: Connector on the bottom of the MR10W