Quick Start Guide

ManualsBrandsSonance ManualsAudioWireless Transmitter and Receiver Kit (Each) - Black

LINE LEVEL INPUT

RIGHTLEFT / LFE

DC IN

5V 1A

PAIR

LINE LEVEL OUTPUT

IGHTLEFT / LFE

DC IN

5V 1A

PAIR

LIN E LEV E

L IN PUT

IG HT

LEFT / LFE

DC IN

5V 1A

PA IR

LIN E LEV EL IN PUT

IG HTLEFT / LFE

C IN

5V 1A

PAIR

Figure 2: Power Supply

and Line Level Input/Output

Figure 4: LED Light

WIRELESS TRANSMITTER AND

RECEIVER QUICKSTART GUIDE

WIRELESS TRANSMITTER AND

RECEIVER QUICKSTART GUIDE

Figure 3: Pair Button

LIN E LEVE L IN PUT

IG HTLEFT / LFE

C IN

5V 1A

PAIR

1. For mounting applications remove

the provided mounting bars and

screws from the bag and secure

them to the transmitter and/or

receiver (see Figure 1).

NOTE: THE 5 VOLT, 1 AMP POWER

SUPPLY MUST BE PLUGGED INTO

A NON-SWITCHED OUTLET.

AC 100 - 120V * 60HZ

AC 220 - 240V *50HZ

3. Connect RCA cables to the

source’s audio output. If you are

using the transmitter and receiver

with a subwoofer, connect RCA

cables from your receiver/

pre-ampliﬁer’s subwoofer/LFE

output to the input of the Sonance

Wireless Transmitter.

4. Connect RCA cables from the

output of the Sonance Wireless

Receiver to the input on the audio

endpoint (AV receiver, preamp,

powered speakers or subwoofer.

BOX CONTENTS

• Sonance Wireless Transmitter

• Sonance Wireless Receiver

• Rack Mounting Bar (x2)

• Power Supply (x2)

• Quickstart Guide (this document)

2. Once your wireless transmitter is in

PAIR mode, the LED light located

on the front of the unit will blink

(see Figure 4).

Figure 1: Attaching the Mounting Bar

3. Within 30 seconds, press and hold

the wireless PAIR button located

on the back of your Sonance

Wireless Receiver.

4. When your Sonance Wireless

Transmitter and Receiver are

paired, the wireless status lights

on the front of both units will turn

solid blue. Your Sonance Wireless

Transmitter and Receiver are now

set up and ready to use.

1. Once your Sonance Wireless

Transmitter and your Sonance

Wireless Receiver are powered on,

press and hold the PAIR button

located on the back of the Sonance

Wireless Transmitter (see Figure 3).

NOTE: THE SONANCE WIRELESS

TRANSMITTER HAS A RANGE OF 30’.

2. Plug the provided power supply

cables into the Sonance Wireless

Transmitter and Receiver

(see Figure 2).

INSTALLATION

SET-UP

Summary of content (2 pages)

PAGE 1
INSTALLATION WIRELESS TRANSMITTER AND RECEIVER QUICKSTART GUIDE 1. For mounting applications remove the provided mounting bars and screws from the bag and secure them to the transmitter and/or receiver (see Figure 1). 2. Plug the provided power supply cables into the Sonance Wireless Transmitter and Receiver (see Figure 2). DC IN 5V 1A NOTE: THE 5 VOLT, 1 AMP POWER SUPPLY MUST BE PLUGGED INTO A NON-SWITCHED OUTLET.
PAGE 2
WARNING PRECAUTIONS • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Clean only with dry cloth. • Do not use this apparatus near water. • Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. • Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.