INSTALLATION MANUAL PROFESSIONAL SERIES IN-CEILING PS-C43RT | PS-C63RT | PS-C83RT | PS-C83RWT PS-C43RTLP | PS-C63RTLP
TABLE OF CONTENTS PRODUCT DESCRIPTION 2 BOX AND CONTENTS 2 PRODUCT FEATURES 3 PRODUCT PREPARATION Amplifier Selection 4 Wire Selection 70V/100V System 4 8 ohm System 4 Speaker Placement 4 Grille Painting 5 INSTALLATION Standard Installation 6 Wiring 6 Drop Ceiling Installation 7 TECHNICAL SPECIFICATIONS PS-C43RT 8 PS-C63RT 9 PS-C83RT 10 PS-C83RWT 11 PS-C43RTLP (Low Profile) 12 PS-C63RTLP (Low Profile) 13 CERTIFICATIONS & SAFETY AGENCY 14 TECHNICAL ASSISTANCE & SERVICE
PRODUCT DESCRIPTION BOX & CONTENTS From Sonance, the company that created the architectural audio category, comes a range of professional loudspeakers that set a new benchmark in sound quality and aesthetics for commercial environments.
PRODUCT FEATURES Transformer Tap and Bypass Selector High Excursion Woofer Tuning Port Pivoting Chambered Tweeter (excluding PS-C83RWT) One Piece Paintable Grille with Magnetic Retention Integrated Back Can Seismic Attachment Cable and Conduit Clamp Connector Cover with Slotted Opening Euroblock Connector with Loop Through Reversible Roto-Lock™ Clamps SONANCE | PROFESSIONAL SERIES 3 IN-CEILING | INSTALLATION MANUAL
AMPLIFIER SELECTION SPEAKER PLACEMENT When choosing an amplifier the maximum number of speakers and the output level of each speaker must be known. The sum of the tap settings should never exceed 80% of the amplifier’s rated output. For example, if there are 5 speakers and the taps are set at 15 watts, the load would be 75 watts (5 x 15 watts = 75 watts). To arrive at the needed power for this number of speakers, simply divide the total load by .8. In this case, 75 / .8 = 93.75 watts.
GRILLE PAINTING Painting The Grilles 1. Prime the grille with a metal primer/bonder in a spray can. Carefully follow the manufacturer’s directions on the can. Before You Begin Sonance Professional Series In-Ceiling speaker grilles completely cover the exposed speaker frame, so only the grilles (not the speakers themselves) require painting. 2. We recommend using water-based latex paint on the grilles.
From Power Amplifier Parallel Connection To Next Speaker INSTALLATION STANDARD INSTALLATION Loop Through Connection STEP 1 Cut a hole in the drywall using the supplied cutout template (see figure 4). NOTE: FOR DROP-CEILING INSTRUCTIONS REFER TO PAGE 7 From Power Amplifier From Power Amplifier Loop Thru Connection To Next Speaker To Next Speaker FIGURE 8: LOOP THROUGH CONNECTION FIGURE 4: CUTOUT TEMPLATE NOTE – IF SQUARE GRILLES ARE BEING USED THE ADAPTER FRAME MUST BE INSTALLED AT THIS TIME.
INSTALLATION STEP 4 STEP 8 Make sure the Roto-Lock Clamps are in the full clockwise position so that all the clamps are tucked within the cutout border. Insert the speaker into the hole in the ceiling (see figure 11). After the speaker is installed, and transformer tap adjustments are made, the grille can be installed. NOTE: THE MAXIMUM CLAMP THICKNESS 1.732” (44MM). TO ACHIEVE MAXIMUM THICKNESS, UNSCREW AND REVERSE THE FOOT OF THE ROTO-LOCK CLAMPS.
PS-C43RT TECHNICAL SPECIFICATIONS LOUDSPEAKER Frequency Range (-10dB): Frequency Range (-3dB): Power Capacity: Crossover Point: Overall Dimension: Cut Out Dimension: Net Weight: Shipping Weight: Unit of Measure: Grille: 57Hz – 25kHz 75Hz – 20kHz 60 Watts Continuous Program Power 30 Watts Continuous Pink Noise 87dB 120 degrees conical coverage 7.6 8.1dB 105dB @ 1 meter (3.3 feet) average, 110dB peak 8 ohms nominal, 6 ohms minimum 70V: 30W, 15W, 7.5W and 3.8W 100V: 30W, 15W and 7.5W 3000Hz 6.
PS-C63RT TECHNICAL SPECIFICATIONS LOUDSPEAKER Frequency Range (-10dB): Frequency Range (-3dB): Power Capacity: Nominal Sensitivity: Nominal Coverage Angle: Directivity Factor (Q): Directivity (DI): Rated Maximum SPL: Rated Impedance: Transformer Taps: Crossover Point: Overall Dimension: Cutout Dimension: Net Weight: Shipping Weight: Unit of Measure: Grille: TRANSDUCERS LF Driver: HF Driver: ENCLOSURE Input Connectors: Knockouts: Safety Agency: Ceiling Thickness Range: Suspension Points: 49Hz – 25kHz 65Hz –
PS-C83RT TECHNICAL SPECIFICATIONS LOUDSPEAKER Frequency Range (-10dB): Frequency Range (-3dB): Power Capacity: Crossover Point: Overall Dimension: Cutout Dimension: Net Weight: Shipping Weight: Unit of Measure: Color: Grille: 41Hz – 25kHz 55Hz – 20kHz 160 Watts Continuous Program Power 80 Watts Continuous Pink Noise 91dB 120 degrees conical coverage 7.6 8.1dB 110dB @ 1 meter (3.3 feet) average, 116dB peak 8 ohms nominal, 6 ohms minimum 70V: 60W, 30W, 15W and 7.5W 100V: 60W, 30W and 15W 2750Hz 11.
PS-C83RWT TECHNICAL SPECIFICATIONS LOUDSPEAKER Frequency Range (-10dB): Frequency Range (-3dB): Power Capacity: Nominal Sensitivity: Nominal Coverage Angle: Directivity Factor (Q): Directivity (DI): Rated Maximum SPL: Rated Impedance: Transformer Taps: Crossover Point: Overall Dimension: Cut Out Dimension: Net Weight: Shipping Weight: Unit of Measure: Grille: TRANSDUCERS LF Driver: HF Driver: ENCLOSURE Input Connectors: Knockouts: Safety Agency: Ceiling Thickness Range: Suspension Points: 32Hz – 300Hz 50Hz
PS-C43RTLP (LOW PROFILE) TECHNICAL SPECIFICATIONS LOUDSPEAKER Frequency Range (-10dB): Frequency Range (-3dB): Power Capacity: Crossover Point: Overall Dimension: Cut Out Dimension: Net Weight: Shipping Weight: Unit of Measure: Grille: 57Hz – 25kHz 75Hz – 20kHz 60 Watts Continuous Program Power 30 Watts Continuous Pink Noise 87dB 120 degrees conical coverage 7.6 8.1dB 105dB @ 1 meter (3.3 feet) average, 110dB peak 8 ohms nominal, 6 ohms minimum 70V: 30W, 15W, 7.5W and 3.8W 100V: 30W, 15W and 7.
PS-C63RTLP (LOW PROFILE) TECHNICAL SPECIFICATIONS LOUDSPEAKER Frequency Range (-10dB): Frequency Range (-3dB): Power Capacity: Nominal Sensitivity: Nominal Coverage Angle: Directivity Factor (Q): Directivity (DI): Rated Maximum SPL: Rated Impedance: Transformer Taps: Crossover Point: Overall Dimension: Cut Out Dimension: Net Weight: Shipping Weight: Unit of Measure: Grille: TRANSDUCERS LF Driver: HF Driver: ENCLOSURE Input Connectors: Knockouts: Safety Agency: Ceiling Thickness Range: Suspension Points: 49
CERTIFICATIONS TECHNICAL ASSISTANCE AND SERVICE SAFETY AGENCY COMPLIANCE Sonance Professional Series loudspeakers models PS-C43RT, PS-C63RT, PS-C83RT, PS-C83RWT, PS-C43RTLP, & PS-C63RTLP, meet the following standards: The Technical Assistance Department at Sonance is available at (949) 492-7777 to answer any questions concerning the operation and installation of your speakers between the hours of 7:00 AM and 5:00 PM Pacific time, Monday through Friday, except holidays.
WARRANTY, REMEDY, EXCLUSIONS AND LIMITATIONS (U.S. ONLY) Limited Warranty: Sonance warrants this product to the original purchaser to be free from defects in material and workmanship, under normal use and conditions, for a period of five (5) years from the date of original purchase as shown on the invoice. Sonance will at its option and expense during the warranty period, either repair the defect or replace the Product with a new or remanufactured Product or a reasonable equivalent.