SONAMP 875D SE 8-CHANNEL AMPLIFIER ® INSTRUCTION MANUAL
Important Safety Information IMPORTANT: Read all of these instructions before you install or operate your 875D SE, and save these instructions for later use. 1 . R e a d I n s t r u c t i o n s — All these safety and operating instructions should be read before you operate the unit. 2 . R e t a i n I n s t r u c t i o n s — These safety and operating instructions should be retained for future reference. 3 .
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER Introduction Thank you for purchasing the Sonance Sonamp ® 875D SE power amplifier. The 875D SE will provide you with many years of home entertainment enjoyment. This manual will teach you all about your new amplifier’s many innovative features and will show you how to get the very best performance from your amplifier. Please read it thoroughly.
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER FRONT PANEL 1–2 L 3–4 R L 5–6 R L 7–8 R L R AUTO ON PROTECTION POWER ACTIVE 1 2 ACTIVE 5 4 3 6 4. Input Level Adjustments (Ch 1 – 8) 5. Auto-On Sensitivity Adjustments (Zones 1 – 4) 6. Protection, BBE On & Status Indicators (Zones 1 –4) 1. Power Button 2. Active LED 3.
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER Box Contents Your Sonamp 875D SE box should contain the following items: (1) Sonamp 875D SE amplifier (2) Rack ears (6) Removable control connectors — connected to the amplifier’s rear panel (4) Removable speaker connectors — connected to the amplifier’s rear panel (1) IEC Power cable Unpacking Save the shipping carton and polystyrene inserts so you can safely transport your amplifier in the future.
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER Protection Circuits Thermal Protection If the amplifier’s cooling vents are blocked, or it is installed with inadequate ventilation the amplifier may exceed its safe operating temperature. If the amplifier’s internal temperature exceeds 154°F (68°C) it will self-protect, and the following will occur: • The audio output to all connected zones will shut OFF. • The front-panel P ROTECTION LEDs (see Figure 3 ) will illuminate yellow .
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER Powering the Amplifier Power Cord (see Figure 4) NOT E : I f y o u n e e d t o u s e a n e x t e n s i o n c o rd , u s e o n ly a h e a v y - d u t y ( 14 - ga u ge o r l a r ge r ) e x t e n s i o n c o rd t o a v o i d s t a r v i n g t h e a m p l i f i e r o f a l l t h e c u r re n t n e c e s s a r y fo r f u l l - p o w e r o p e ra t i o n .
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER Source Connections (see Figures 6 & 7 ) INPUT Always use quality high-fidelity interconnect cables such as Sonance MediaLinQ ® Bronze Interconnects. If source components are more than 20 feet from the amplifier, use the Sonance LS2 and LR2 Balanced Line-Level Sender and Receiver (sold separately) to avoid signal degradation. L NOTE: Always check local building codes before installing wire in walls or ceilings.
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER Input Sensitivity Adjustment There are two ways to adjust the individual channel input sensitivity (volume) on the 875D SE: • The front panel has recessed adjustment potentiometers (see Figure 9 ). These can be adjusted using a small screwdriver. 3–4 • Input sensitivity can also be adjusted by serial command via the amplifier’s RS-232 connection (see page 14).
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER 6. Press the removable connector into the corresponding zone speaker connector on the amplifier until it locks into place. • The removable connectors will only fit one way on the amplifier. CAUTION : Always provide sufficient slack in wires to avoid tension. Always contain any excess wire to prevent tripping hazards.
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER Auto-On TRIGGER MODE AUTO VOLT AUTO CH 3/4 VOLT AUTO CH 5/6 VOLT AUTO CH 7/8 VOLT OFF ON You can set your 875D SE so that any zone will automatically turn ON when it receives an audio signal, or when it receives a control voltage from an external source (such as a Sonance Navigator Harbor multi-zone controller).
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER OFF (Bypass) Mode When a zone’s A UTO and V OLT Auto-On Trigger switches are both set in the OFF position, the A UTO -O N circuitry is bypassed and the amplifier’s front-panel P OWER button will turn all zones ON and OFF simultaneously (see Figure 2 , on page 5). BBE CONTROL OFF LOW OFF LOW OFF LOW OFF LOW The Sonamp 875D SE incorporates BBE ® Sound Enhancement.
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER Zone Trigger Outputs The 875D SE has individual T RIGGER O UTPUT connections for each zone that provide 12V DC whenever the zone is ON (see Figure 18 ). This trigger can be used to control other devices such as Sonance AL2/AS2 automatic secondary switches, other Sonamps or 12V relays. • The current draw on each zone’s T RIGGER O UTPUT connection should not exceed 200mA.
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER 875D SE Serial Commands Serial Protocol: Baud Rate = 9600, N, 8, 1; single CR Commands In Syntax Parameters State Power :Pxy x = Zone 1-4 or G (Global), y = State 0= Off; 1= On Zone Volume Set :Vxyyy x = Zone 1-4 or G (Global), yyy = Volume 0 - 100 0 (Off) – 100 (Max) Channel Volume Set :VCxyyy x = Channel 1 - 8 or G (Global), yyy = Volume 0 - 100 0 (Off) – 100 (Max) NOT E : I s s u i n g a Volume Set c o m m a n d w h e n t h e a m p l i f i e
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER Serial Control Notes: 1. The 875D SE will respond to each command with the new value after the command is acted-upon. E x a m p l e : Zone 2 volume is 53. If a “:V2+3” (increase Zone 2 volume +3 steps) command is then issued, the 875D SE echoes back (V256) (Zone 2 volume is 56). 2. The 875D SE will respond to invalid commands with “ERR”. E x a m p l e : A “:V7?” poll is received (What is Zone 7 volume?). Since there is no Zone 7, the 875D SE echoes back “ERR”. 3.
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER Specifications Number of Channels: 8 (four stereo pairs) Output Power (Stereo): 75 watts RMS per channel (X8), 0.25% THD, 20Hz – 20kHz, @ 8 ohms; 140 Watts per channel (X8), 0.1% THD, 1kHz, @ 4 ohms Output Power (Bridged): 300 Watts per channel (X4) @ 8 ohms Frequency Response: 20Hz – 20kHz, ±1dB Total Harmonic Distortion: 0.05% (1kHz, 8 ohms); 0.10% (1kHz, 4 ohms) Signal to Noise Ratio: -96dB (w/22kHz filter) Input Sensitivity: 1.5V for 75W RMS Output 1.
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER System 1: Basic Background Music System with Paging Capabilities Features: Common Music Source for all Four Rooms • Two Zones with Paging Capabilities Connecting a telephone page output (residential) or microphone preamp output (commercial) to the 875D SE’s Aux Bus input and a music source to the L EFT & R IGHT B US inputs lets you mix a music source with a paging signal.
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER System 2: 7.1-Channel Home Theater System Features: Up to 140W output power per channel (4-ohms) • Allows use of passive in-wall subwoofer The 875D SE can power all eight channels of a 7.1-channel home theater system while occupying only 2U of rack space. The surround sound processor’s preamp outputs feed each channel’s D IRECT I NPUT C ONNECTION , and each channel’s I NPUT A SSIGNMENT DIP S WITCH is set to D IRECT .
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER System 3: Multi-Zone System with Controller Features: Channels automatically activated by controller • Each zone can be controlled by in-zone keypad The 875D SE is ideal for use with a multi-zone controller like the Sonance Navigator ® Harbor. By connecting the Navigator Harbor’s Zone Keypad Status + and – terminals to the 875D SE’s External Control Input connections, the controller will automatically turn the amplifier’s channels ON and OFF as they are needed.
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER System 4: Advanced Multi-Zone System with Central Control System Features: Serial control of amplifiers • Amplifier parameters can be monitored on controller display The 875D SE’s RS-232 connector allows it to be directly controlled by central whole-home control systems. The system programmer can build the 875D SE’s functions into macros, and can display amplifier operating parameters on the controller’s touchscreen displays.
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER System 5: Automatic Input Switching Between Sources Using an AL2 Selector Features: Automatically selects iPort when iPod is played • Automatically activates BBE when iPod is played By feeding two sources through a Sonance AL2 Automatic Secondary Source Selector, the system will automatically select the I NPUT B source whenever the iPort/iPod is playing.
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER System 6: Using a K2 Keypad to Control the 875D SE’s BBE Sound Enhancement Features: User can turn BBE Sound Enhancement ON/OFF from inside the listening zone The Sonance Navigator K2 Keypad Controller can be used to manually turn the 875D SE’s BBE Sound Enhancement ON and OFF in the zone it is controlling.
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER Technical Assistance and Service If you any have questions about the operation or installation of this product, please call our Technical Assistance Department on any business day at (800) 582-0772 or (949) 492-7777; from 7 a.m. to 5 p.m., Pacific Time. If your product should need repair or service, contact your Sonance Authorized Dealer for help, or use the following procedure: 1.
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER Limited Warranty Coverage (U.S.A. Only) Sonance warrants to the original retail purchaser only that this Sonance product will be free from defects in materials and workmanship for a period of five (5) years, provided the product was purchased from a Sonance Authorized Dealer.
SONAMP ® 875D SE 8-CHANNEL AMPLIFIER System Notes: 26
©2007 Sonance. All rights reserved. Sonance and Sonamp are registered trademarks of Dana Innovations. Digital Power Processing is a trademark of Tripath Technology, Inc. Crestron is a trademark of Crestron Electronics, Inc. AMX is a trademark of AMX Corporation. Due to continuous product improvement, all features and specifications are subject to change without notice. For the latest Sonance product specification information visit our website: www.sonance.