Sonance DSP2-750 MKII Amplifier Rear Panel 4/ 2/ 2018 SONAMP TWO-CHANNEL POWER AMPLIFIER WITH SonARC V2 Die Line Do N ot Print Prints W hite INSTRUCTION MANUAL DSP 2-750 MKII S/N CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR 1-L 1-R 2-L 2-R IN IN IR CONTROL IR STATUS IN DSP 2-750 MKII 1 - RIGHT OUT 1 - LEFT OUT + + _ _ BRIDGE 4 Ω MIN + _ IN + OUT T10AL/250VAC CAUTION REPLACE FUSE ONLY WITH SAME TYPE AND RATING OF FUSE ATTENTION REMPLACER
TABLE OF CONTENTS Safety 2 Introduction/Box Contents 3 Front Panel/Rear Panel 4 Amplifier Power Requirements 6 Connections & Volume Level Controls 7 Protection Circuitry & LEDs/Stacking 8 Network Connection Instructions 9 Basic Setup 9 Advanced Setup 10 Specifications 15 Appendix A & B 16 Troubleshooting 17 Warranty 1 19
n IMPORTANT SAFETY INFORMATION 10. Power Sources — The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. IMPORTANT: READ ALL OF THESE INSTRUCTIONS BEFORE YOU INSTALL OR OPERATE YOUR SUBWOOFER AND SAVE THESE INSTRUCTIONS FOR LATER USE. 11. Accessories and Attachments — Only use accessories and attachments specified by the manufacturer. 1.
Introduction Unpacking Thank you for purchasing the Sonance Sonamp DSP 2-750 MKII amplifier. When properly installed, this amplifier will give you many years of entertainment pleasure. To get the most out of your new Sonance MKII Amplifier amplifier, DSP2-750 please read this manual thoroughly before you installation. Rearbegin Panel 4/ 2/ 2018 Save the carton and polystyrene inserts for future safe transport in case the amplifier is moved or requires shipping for repair.
S/N CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR 1-L 1-R 2-L 2-R DSP 2-750 MKII Front Panel IN IN 1 - RIGHT 1. Illuminated Power Button OUT 1 - LEFT OUT IR CONTROL IR STATUS IN 2.
Front Panel Power Button The power button turns the amplifier on and off. When the Sonance llogo power button is engaged, the power button is illuminated solid white. This means amplifier has power and is turned ON and ready to operate. When the Sonance logo is slightly dimmed, the amplifier is in standby mode. When the Sonance logo blinks white, the amplifier power supply is in thermal protection.
IMPORTANT: DO NOT PLUG THE AMPLIFIER’S POWER CORD INTO A CONVENIENCE OUTLET ON ANY OTHER AUDIO OR VIDEO COMPONENT. IMPORTANT: THE AMPLIFIER IS SET TO 70 VOLTS FROM THE FACTORY. CHANGES TO THE POWER CAN BE MADE IN THE SONARC SOFTWARE. If the electrical service is subject to frequent sags, spikes or brownouts, a power conditioner designed for use with high fidelity equipment should be employed to protect the amplifier.
Do N ot Print Speaker Connections Source Connections DSP 2-750 MKII For the best sound you should use premium speaker wire that complies with fire rating codes. Be sure to check local codes governing wire that may be installed within walls or ceilings. Sonamp amplifiers are stable with any reputable brand of speaker wire or cable. The Sonamp amplifiers use speaker block connectors that can accommodate up to 12 gauge wire (see Figure 9).
Protection Circuitry and LEDs Rack Ear Installation DSP 2-750 MKII The Sonamp amplifiers have a multi-stage protection system to prevent damage to your amplifier and speakers. The DSP 2-750 MKII ships with two rack ears. Unscrew the four Phillips head screws (M4 x 0.7 pitch x 10mm long) found on each side of the left and right forward section of amplifier. Use these screws to connect the included rack ears to the amplifier (see Figure 15).
Basic Setup Page SonARC Software Network Connection Instructions This page is for basic setup of EQ, source and volume. To start, click on the Basic Setup button. Equipment List (1) Computer or tablet (1) Network router with DHCP service enabled (2) RJ-45 cables (one when using wireless) Connecting to Your SonARC Homepage 1. The amplifier’s factory default settings has DHCP set to ON. 2. Connect the amplifier to a network with a router. Make sure the computer and amplifier are on the same network.
Output Settings/Output Volume General Settings Tab Output Name This is a user entered field with a maximum of 15 characters. Use these fields to describe the room or area the channel will be powering. The Advanced Setup automatically starts out on the General Settings tab. This tab is used to set up your MKII with a network network connection, auto on method and other basic information. Output Volume (Basic Set-Up) Play music with wide dynamics and bass that will stress the system. 1.
IP Subnet Mask The third setting in the IP SETUP section is the IP Subnet Mask. This is an advanced network setup function. Under most circumstances this field should not need to be edited. Making changes in this field should only be done by an experience network administrator. Voltage In the Voltage Auto On mode, the amplifier will power off immediately when the trigger voltage has been removed.
In/Out Settings Tab Mode Source 2 Off When set to OFF, Source 2 has no effect on the operation of the channel. The IN/OUT settings tab is used to assign your MKII’s input and output specifications. Mix When set to MIX, Source 1 and Source 2 will be blended together when a signal is present on Source 2. Input Setup Input Name This is a user entered field with a maximum of 15 characters. Use these fields to describe the type of input connected.
Assign Preset Export Single Preset 1. Use the blue pull down menu SELECT PRESET to edit located above the IMPORT EXPORT green buttons. Output Name These can be named Output 1L & Output 1R or room names such as Kitchen L and Kitchen R. These are a duplicate of the output name on the IN/OUT settings page. 2. Select the preset you choose to export from the pull down menu. 3. Press the green EXPORT button.
Parametric EQ Crossover All Sonance DSP amplifier models feature a 10 band parametric EQ. Adjustments made to the EQ will be displayed on the output frequency response graph. We strongly suggest not adjusting the EQ without proper measurement equipment. LP Xover / HP Xover This setting turns the high and low pass crossovers on and off. Frequency In this field you can enter any frequency between 20Hz-20kHz. EQ On/Off Turns each of the 10 parametric EQ filters on and off.
Specifications SONAMP DSP 2-750 MKII Number of Channels 2 (1 stereo pair) Power Output - 8 ohms (Stereo) 500 Watts RMS per channel (all channels driven) Power Output - 4 ohms/70V (Stereo) 750 Watts RMS per channel (all channels driven) Power Output - 8 ohms (Bridged) 2000 Watts Power Output - 70 Volts 750 Watts RMS per channel (both channels driven) Frequency Response 5Hz – 50kHz, bandwidth limited Total Harmonic Distortion 0.4% (1kHz, 8 ohms) 0.
APPENDIX A Explanation LED Indicator Dim White Power Button Amplifier is plugged in and in standby mode. Bright White Power Button Amplifier is active. Power Button Blinking The amp is in ID Amp Mode (see page 9). Green LED Signal is present (>1.0mv) on channel. Blinking Green Signal is going above and below the active level or between songs. Blinking Red The channel is being over driven. Solid Red The amp is in protection mode (see page 6).
Out of the Box Troubleshooting Cause: The SonARC bridging option is engaged but the speakers are not wired properly for bridge mode. No Power Front panel Power LED does not illuminate when AC cord is plugged into an outlet and the amp is switched on. Solutions: • Set the bridge mode to OFF. If audio output is still unavailable, contact Dana Innovations Technical Support. Cause: AC cable is improperly seated either at the back of the amp or at the AC outlet.
Factory Reset Channel Out Perform a factory reset procedure on the DSP amp using a small flat head jewelers screwdriver. One channel of the amp does not have output. Cause: Solutions: Line-level interconnect cable from the source to the affected amp channel is loose, disconnected or faulty. • With the amp powered OFF, carefully rotate the front panel accessed 1L volume control fully-counterclockwise and rotate the 1R volume control to fully-clockwise.
LIMITED TWO (2) YEAR WARRANTY Sonance warrants to the first end-user purchaser that this Sonance-brand product (product), when purchased from an authorized Sonance Dealer/Distributor, will be free from defective workmanship and materials for the period stated below. Sonance will at its option and expense during the warranty period, either repair the defect or replace the Product with a new or remanufactured Product or a reasonable equivalent.