- Dana Innovations Inc Stereo Amplifier User Manual

ManualsBrandsSonance ManualsAmplifierSonance - Dana Innovations Inc Stereo Amplifier ASAP2 SAT

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: Read all of these instructions before you operate and

save instructions for later use.

1. Read Instructions - all the safety and operating instructions should be read

before the appliance is operated.

2. Retain Instructions - The safety and operating instructions should be retained for

future reference.

3. Heed Warnings - All warnings on the appliance and in the operating

instructions should be adhered to.

4. Follow Instructions - All operating and use instructions should be followed.

5.Water and Moisture- The appliance should not be used near water - for

example, near a bathtub, washbowl,kitchen sink, laundry tub, in a wet

basement, or near a swimming pool.

6. Carts and Stands - The appliance should be used only with a cart or stand

that is stable and sturdy enough to hold the product. An appliance and cart

combination should be moved with care. Quick stops, excessive force and

uneven surfaces may cause the appliance and cart combination to overturn.

7. Caution: To prevent electric shock, do not use this (polarized) plug with an

extension cord,receptacle or other outlets unless the blades can be fully

inserted to prevent blade exposure.

8.Ventilation - The appliance should be situated so that its location or position

does not interfere with its proper ventilation. For example, the appliance should

not be situated on a bed, sofa, rug, or similar surface that may block the

ventilation openings or, placed in a built-in installation, such as a bookcase or

cabinet that may impede the flow of air through the ventilation openings.

9. Heat - The appliance should be situated away from heat sources such as

radiators,heat registers, stoves,or other appliances (including amplifiers)

that produce heat.

10. Power Sources - The appliance should be connected to a power supply

only of the type described in the operating instructions or as marked on

the appliance.

11. Grounding or Polarization - Precautions that should be taken so that

the grounding or polarization of the appliance is not defeated.

12. Power-Cord Protection - Power supply cords should be routed so that they

are not likely to be walked on or pinched by items placed upon or against

them, paying particular attention to cords at plugs,convenience

receptacles, and the point where they exit from the appliance.

13. Cleaning - Dust the product with a clean cloth. NEVER use water.

14. Non-use Periods - The power cord of the appliance should be unplugged

from the outlet when left unused for a long period of time.

15. Object and Liquid Entry - Care should be taken so that objects do not fall

and liquids are not spilled into the enclosure through openings.

16. Damage Requiring Service - The appliance should be serviced by qualified

service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen,or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain.

D. The appliance does not appear to operate normally or exhibits a marked

change in performance.

E. The appliance has been dropped, or the enclosure damaged.

17. Servicing - The user should not attempt to service the appliance beyond

that described in the operating instructions. All other servicing should be

referred to qualified service personnel.

INSTALLATION INSTRUCTIONS

SONAMP

ASAP2 SAT

STEREO POWER AMPLIFIER

PN.33-2381 4.02

33-2381 asap2 manual.qxd 4/29/02 1:13 PM Page 1

Summary of content (6 pages)

PAGE 1
33-2381 asap2 manual.qxd 4/29/02 1:13 PM Page 1 INSTALLATION PN.33-2381 4.02 IMPORTANT SAFETY INSTRUCTIONS CAUTION: Read all of these instructions before you operate and save instructions for later use. 1. Read Instructions - all the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions - The safety and operating instructions should be retained for future reference. 3.
PAGE 2
33-2381 asap2 manual.qxd 4/29/02 1:13 PM Page 2 ASAP2 SAT MOUNTING SCREW HOLES DO NOT PLUG THE ASAP2 IN UNTIL ALL OTHER CONNECTIONS ARE MADE. MAKE SURE ALL SOURCE AMPLIFIERS BEING CONNECTED TO THE UNIT ARE OFF MAKING CONNECTIONS Before making any signal or speaker connections, make sure your power amplifier is turned off and unplugged. When making connections, make sure there is no strain or tension on input leads or speaker wires that could cause them to pull loose later on.
PAGE 3
3-2381 asap2 manual.qxd 4/29/02 1:13 PM Page 3 Polarity OPERATING THE ASAP2 It is important to observe correct polarity when using stereo mode. One side of the speaker lead will have some sort of mark, either printing, a raised ridge on the insulation or different color of conductor. This permits you to know which wire you had connected to the + and which to the - speaker terminals so you can do exactly the same at the power amplifier terminals.
PAGE 4
33-2381 asap2 manual.qxd 4/29/02 1:13 PM Page 4 Note: the video jack is for triggering purposes only; video signal switching is not possible. more difficult to trigger.In this case audio,video or low voltage may be an alternative option for better triggering stability. External Voltage Trigger (Dip switch #2 On -- UP Position) Local to Main Delay Control Time Adjustment (front panel) The B input relay may also be activated by a low voltage control source.
PAGE 5
33-2381 asap2 manual.qxd 4/29/02 1:13 PM Page 5 1. Unscrew and save the two screws holding the current module in place. 2. Pull the module out of the SAT module bay. 3. Disconnect the ribbon cable. 4. Select the desired position of any jumpers on the SAT module (i.e. high pass filter). 5. Connect the ribbon cable to the ribbon cable connector on the new module. 6. Slide the SAT module into the SAT module bay. 7. Replace the two mounting screws.
PAGE 6
33-2381 asap2 manual.qxd 4/29/02 1:13 PM Page 6 SERVICE WARRANTY COVERAGE (USA ONLY) If you have any questions about the operation or installation of your Sonamp® ASAP2, please call our Technical Assistance Department on any business day at: (800)582-0772 or (949)492-7777 from 7 a.m. to 5 p.m. PST.