I N S T R U C T I O N M A N UA L SR 2-125 TWO-CHANNEL AMPLIFIER 33-7575 05.24.
SR 2-125 TWO-CHANNEL AMPLIFIER INSTRUCTION MANUAL TABLE OF CONTENTS Safety 1 Introduction/Box Contents 3 Front Panel/Rear Panel 4 Amplifier Power Requirement Chart 6 Connections and Volume Level Controls 7 Protection Circuitry and LEDs 8 Quick Setup Page 9 Specifications 10 Warranty 11
INSTRUCTION MANUAL SR 2-125 TWO-CHANNEL AMPLIFIER Important Safety Information • The amplifier has been exposed to rain. • The amplifier does not appear to operate normally or exhibits a marked change in performance. You should always follow these basic safety precautions when using your SR 2-125 amplifier to reduce the risk of fire, electric shock, and injury to persons: • The amplifier has been dropped, or the enclosure damaged. 1.
SR 2-125 TWO-CHANNEL AMPLIFIER INSTRUCTION MANUAL I N S T R U C T I O N S I M P O R TA N T E S C O N C E R N A N T L A S É C U R I T É 10. Protégez le câble d’alimentation secteur de telle manière qu’il ne puisse pas être écrasé ou pincé, particulièrement au niveau des prises, du passage dans des goulettes prévues à cet usage, ou à l’endroit où il sort de l’appareil. 1. Lisez soigneusement ces instructions. 2. Conservez-les en lieu sûr pour toute référence future. 3.
SR 2-125 TWO-CHANNEL AMPLIFIER INSTRUCTION MANUAL Introduction Unpacking Thank you for purchasing the SONARRAY SR 2-125 amplifier. When properly installed, this amplifier will give you many years of entertainment pleasure. To get the most out of your new amplifier please read this manual thoroughly before you begin installation. Save the carton and polystyrene inserts for future safe transport in case the amplifier is moved or requires shipping for repair.
SR 2-125 TWO-CHANNEL AMPLIFIER INSTRUCTION MANUAL FIGURE 2: SR 2-125 TWO-CHANNEL AMPLIFIER FRONT PANEL 1 2 3 SR 2-125 Front Panel 1. Illuminated Power Button 2. Power, Active & Protection Indicator LED 3. Recessed Volume Level Control FIGURE 3: SR 2-125 TWO-CHANNEL AMPLIFIER BACK PANEL 4 6 9 10 5 7 SR 2-125 Rear Panel 4. L/R Line In/Coax/Toslink 8. EQ Preset Selection 5. Speaker Block Connector 9. AC Fuse Holder 6. Audio Auto On/Off Switch 10. Power Cord Connection 7.
SR 2-125 TWO-CHANNEL AMPLIFIER INSTRUCTION MANUAL FIGURE 4: SR 2-125 AMPLIFIER FRONT PANEL VIEW FIGURE 5: SR 2-125 AMPLIFIER REAR PANEL VIEW Front Panel Rear Panel Power Switch The power switch turns the amplifier on and off. Inputs The SR 2-125 amplifier has analog, coax and toslink LINE INPUTS and loop OUTPUTS. When the power switch is lit solid white, the amplifier has power, is turned ON and ready to operate. The analog loop outputs are non buffered.
Source Connections/Selection SR 2-125 The SR 2-125 features a removable IEC power connector (Figure 6). AVOLTAGE 14-gauge EIA standard 120-volt TRIGGER grounded power cable is included with theIN amplifier. OUT AUTO ON There are two options when connecting audio inputs to the SR 2-125 amplifier (see Figure 8): RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS ON RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR AUDIO VOLTAGE Primary Line Inputs 1-L, 1-R - Use these inputs for analog audio source.
SR 2-125 TWO-CHANNEL AMPLIFIER INSTRUCTION MANUAL Speaker Connections Volume Level Control For the best sound you should use premium speaker wire that complies with fire rating codes. Be sure to check local codes governing wire that may be installed within walls or ceilings. SONARRAY amplifiers are stable with any reputable brand of speaker wire or cable. The SR 2-125 amplifiers use speaker block connectors that can accommodate up to 12 gauge wire (see Figure 9).
SR 2-125 TWO-CHANNEL AMPLIFIER INSTRUCTION MANUAL Protection Circuitry and LEDs Shelf Mounting The SR 2-125 amplifiers have a multi-stage protection system to prevent damage to your amplifier and speakers. If shelf mounting, attach the four included feet by screwing them into the threaded openings, no tool is required. SR 2-125 Amplifier Channel Protection If a channel encounters a short-circuit or an extremely low impedance this will cause the affected channel outputs to automatically mute.
SR 2-125 TWO-CHANNEL AMPLIFIER INSTRUCTION MANUAL Quick Setup Page Quick Setup Apply DSP Preset Audio - Auto On Select the Audio Auto On mode you would like to use, either ON or OFF. The SR 2-125 amplifier includes pre-programmed DSP presets. These presets are selected utilizing first the EQ Preset Bank dial, followed by the EQ Preset Selection dial (see included DSP Preset Matrix). The first EQ in any bank will be Flat.
SR 2-125 TWO-CHANNEL AMPLIFIER INSTRUCTION MANUAL SPECIFICATIONS SR 2-125 Amplifier Number of Channels 2 (1 stereo pair) Power Output - 8 ohms 125 Watts RMS per channel (both channels driven) Power Output - 4 ohms 200 Watts RMS per channel (both channels driven) Frequency Response 5Hz - 50kHz, bandwidth limited Total Harmonic Distortion 0.07% (1kHz, 8 ohms) 0.
SR 2-125 TWO-CHANNEL AMPLIFIER INSTRUCTION MANUAL LIMITED TWO (2) YEAR WARRANTY SONARRAY warrants to the first end-user purchaser that this SONARRAY-brand product (“Product”), when purchased from an authorized SONARRAY Dealer/Distributor, will be free from defective workmanship and materials for the period stated below. SONARRAY will at its option and expense during the warranty period, either repair the defect or replace the Product with a new or remanufactured Product or a reasonable equivalent.