A delicately scaled, modular system of interconnected elements and suspended LED luminaires. suspenders ® assembly instructions Double Single Ring (S1F) Multiple U.S. and foreign patents granted and pending.
LED Product Information and Warnings June 10, 2019 Important • Always disconnect the power before installing or replacing parts and before cleaning or other maintenance. • Consult a qualified, licensed electrician to ensure correct branch circuit conductor. • Please read all included assembly instructions and warnings carefully before installation. Contact Customer Service if you have any questions or concerns.
Suspenders ® Contents Power Bars . . . . . . . . . . . . . . . . . . . . . . . . 2 Power Feed Hangers . . . . . . . . . . . . . . . . . .3 Ceiling Hangers . . . . . . . . . . . . . . . . . . . . . 5 Wall Mount System . . . . . . . . . . . . . . . . . . .7 Ceiling Mount System . . . . . . . . . . . . . . . . . 8 Power Bar Hanger . . . . . . . . . . . . . . . . . . . .
June 10, 2019 Power Bars Assembly Instructions Applies to Components: 1XC02XX12x INSTRUCTIONS D’INSTALLATION Tri-Bar Power Bar Assembly: 1. Insert one of the Arms onto the Center Hub, and secure with the four Phillips Screws (Fig. 1). 2. Repeat for the other Arm (Fig. 2). 1XC02XX24x Phillips Screws Center Hub Arm Fig. 1 Fig. 2 Linear Power Bar Assembly: Applies to Components: 1.
June 10, 2019 Power Feed Hangers Assembly Instructions Applies to Components: 1XB01SC06x 1XB01SC20x INSTRUCTIONS D’INSTALLATION Single Cord Power Feed Hanger: NOTE: Each Single Cord Power Feed Hanger only carries half of the electrical circuit, and must be used in pairs. To avoid shortcircuiting the system, the spring contacts must point in different directions. 1XB01RC06x 1XB01RC20x Set Screw Allen Key 1.
June 10, 2019 Power Feed Hangers Assembly Instructions Applies to Components: 1XB01PT00x INSTRUCTIONS D’INSTALLATION In-Line Power Tap Hanger: 1. Install Double Cord Power Feed Hanger to Lower Power Bar and connect to the Power Feed by inserting the exposed wires into the Power Feed Bushings. Secure by tightening the Set Screws with the included Allen Key (Fig. 1). 2. Install the Upper Power Bar between the two cords of the Double Cord Power Feed Hanger using appropriate hangers. 3.
June 10, 2019 Ceiling Hangers Assembly Instructions Applies to Component: 1XB02SB06x 1XB02SB20x INSTRUCTIONS D’INSTALLATION 1XB02SB06x-ST 1XB02SB20x-ST 1XB02RB06x 1XB02RB20x 1XB02SR18x Ceiling Hanger Assembly: 1. Install the Mounting Bracket to the ceiling with Anchor (if appropriate) and Screw, then screw the Post onto the Mounting Bracket (Fig. 1). 2.
June 10, 2019 Ceiling Hangers Applies to Components: Assembly Instructions 1XB02IB06x 1XB02IB20x INSTRUCTIONS D’INSTALLATION 1XB02IB06x-ST 1XB02IB20x-ST 1XB02IR18x In-Line Ceiling Hanger Assembly: 1. Install the Mounting Bracket to the ceiling with Anchor (if applicable) and Screw, then screw the Post onto the Mounting Bracket (Fig. 1). 2. For Hanger with Stem: Hand screw the Stem onto the Ceiling Hanger (Fig. 2). 3. Attaching the Ceiling Hanger Rod/Cable into the Post: a.
June 10, 2019 Wall Mount System Assembly Instructions Applies to Components: 1XB02WL00x INSTRUCTIONS D’INSTALLATION 1XB02WL01x Wall Flush Mount Support: 1. Install the Mounting Bracket to the wall with Anchor (if applicable) and Screw, align set screw holes with the direction of Power Bar, then attach the Support onto the Mounting Bracket and tighten the two Set Screws with the Allen Key (Fig. 1). 2. Remove Flat Head Screw and Support Cap and align Power Bar with Support (Fig. 2). 3.
June 10, 2019 Ceiling Mount System Assembly Instructions Applies to Components: 1XB02CE00x INSTRUCTIONS D’INSTALLATION 1XB02CE01x Ceiling Flush Mount Support: 1. Install the Mounting Bracket to the ceiling with Anchor (if applicable) and Screw, align set screw holes with the direction of Power Bar, then attach the Support onto the Mounting Bracket and tighten two Set Screws with the Allen Key (Fig. 1). 2. Remove Flat Head Screw and Support Cap and align Power Bar with Support (Fig. 2). 3.
June 10, 2019 Power Bar Hangers Assembly Instructions Applies to Components: 1XB03ARxxx INSTRUCTIONS D’INSTALLATION Parallel Power Bar Hanger: 1. Pass one end of the Parallel Power Bar Hanger over the end of a Power Bar (Fig. 1). 2. Press down firmly on the top of the Power Bar Hanger, while pressing up on the bottom of the Power Bar, until the Power Bar Hanger clicks into place (Fig. 2). 3. Pass a second Power Bar between the rods of the Power Bar Hanger (Fig. 3). 4.
June 10, 2019 Power Bar Hangers Assembly Instructions Applies to Components: 1XB03PRxxx INSTRUCTIONS D’INSTALLATION Perpendicular Power Bar Hanger v2: 1. Press down firmly on the top of the Power Bar Hanger, while pressing up on the bottom of the Power Bar, until the Power Bar Hanger clicks into place (Fig. 2). 2. Push up on the bottom of the Power Bar Hanger Cover, while pressing down on the bottom of the Power Bar, until the Power Bar Hanger Cover clicks into place (Fig. 3). 3.
June 10, 2019 Power Bar Hangers Assembly Instructions Applies to Components: 1XB02TR06x-EN 1XB02TR06x-EX 1XB03TR16x-EN INSTRUCTIONS D’INSTALLATION 1XB03TR16x-EX 1XB02TR20x-EN 1XB02TR20x-EX 1XZ05000xx Truss Hanger System: 1. Where applicable: Install the Mounting Bracket to the ceiling with Anchor (if applicable) and Screw, then screw the Post onto the Mounting Bracket (Fig. 1). 2.
June 10, 2019 Power Bar Hangers Assembly Instructions INSTRUCTIONS D’INSTALLATION Applies to Components: Applies to Components: 1XB03PR00x 1XB03IB00x Flush Perpendicular Power Bar Hanger: In-Line Power Bar 1. Remove Flat Head Screws and both Hanger Caps (Fig. 1). Connector: 2. Align Power Bars with Hanger (Fig. 2). Press down firmly on the top of 1. Align In-Line Connector with Power Bar (Fig.
June 10, 2019 Luminaires and Luminaire Hangers Assembly Instructions Applies to Components: INSTRUCTIONS D’INSTALLATION 1XDXXRPxxx 1XB04DRxxx 1XB04RDxxx 1XB04DR16x-RG Connecting an RPxx Luminaire to an ARxx, RPxx, and DRxx Double 1XB04ARxxx Luminaire Hanger (Fig. 1): 1. Gently insert the two Luminaire Hanger Rods into the holes on the top of the Luminaire. 2. Rotate the Luminaire or Luminaire Hanger 90 degrees. 3.
June 10, 2019 Luminaires and Luminaire Hangers Assembly Instructions Applies to Components: 1XB04ARxxx INSTRUCTIONS D’INSTALLATION Connecting a Parallel Luminaire Hanger to a Power Bar: 1. Place the Parallel Luminaire Hanger under the Power Bar. 2. Press up firmly on the bottom of the Parallel Luminaire Hanger, while pressing down on the top of the Power Bar, until the Parallel Luminaire Hanger clicks into place (Fig. 1). 3.
June 10, 2019 Luminaires and Luminaire Hangers Assembly Instructions INSTRUCTIONS D’INSTALLATION Calla: 1. Curl the Petal into a conical shape and align the two outer holes with each other (1). 2. Align Petal with the fixture Branches (2). 3. Secure Petals to Branches by hand screwing the two Pins onto the fixture for each Branch (3) Applies to Components: 1XDXXCL14x-XX 1XDXXCL16x-XX 1XZ990007x 1XZ990010x Glass Cluster Luminaires: Applies to Components: 1.
June 10, 2019 Luminaires and Luminaire Hangers Assembly Instructions Applies to Components: 1XB04CL09x INSTRUCTIONS D’INSTALLATION 1XB04CL18x Connecting a MonolineTM Luminaire Hanger to a Power Bar: 1. Place the MonolineTM Luminaire Hanger under the Power Bar. 2. Press up firmly on both sides the bottom of the MonolineTM Luminaire Hanger, while pressing down on the top of the Power Bar, until the Luminaire Hanger clicks into place (Fig. 1). 3.
June 10, 2019 Luminaires and Luminaire Hangers Assembly Instructions Applies to Component: 1XZ990001x INSTRUCTIONS D’INSTALLATION Connecting a Luminaire Hanger Endcap to a Luminaire Hanger: 1. Gently insert the two Luminaire Hanger Rods into the holes on the top of the Luminaire Hanger Endcap (Fig. 1). 2. Rotate the Endcap or Luminaire Hanger 90 degrees (Fig. 2). 3. Push the Luminaire Hanger Rods into the Endcap until the copper on the ends of the Rods is no longer visible (Fig. 3). 4.
June 10, 2019 Luminaires and Luminaire Hangers Assembly Instructions Applies to Components: 1XDXXLB12x 1XDXXLB24x INSTRUCTIONS D’INSTALLATION Connecting a Light Bar onto a Power Bar: 1. Place the Light Bar on the Power Bar. 2. Press down firmly on the top of both ends of the Light Bar, while pressing up on the bottom of the Power Bar, until the Light Bar clicks into place (Fig. 1). Light Bar 1XDXXLB36x 1XZ990005x Removing a Light Bar from a Power Bar: 1.
June 10, 2019 Luminaires and Luminaire Hangers Assembly Instructions Applies to Components: 1XB04SRxxx 1XDXXSR01x-xx INSTRUCTIONS D’INSTALLATION Connecting Linear Rotational Luminaire to Single Rod Luminaire Hanger: 1. Align Linear Rotational Luminaire with both Hangers (Fig. 1). 2. Insert Luminare onto Hangers and secure with Set Screws (Fig. 2). Note: Luminaire can rotate 360° (Fig. 2). Hanger Single Rod Luminaire Hanger: 1. Make sure Spring Contacts of each Hanger face opposite directions (Fig.
June 10, 2019 Luminaires and Luminaire Hangers Assembly Instructions Applies to Components: 1XDXXRH01x 1XDXXRH02x 1XDXXRH03x 1XDXXRH04x INSTRUCTIONS D’INSTALLATION Precise Blade Mount Hanger and Precise Bar-Mounted Aimable Light Engine: 1. Align Hanger with Power Bar (Fig. 1) and press down firmly on the top of the Power Bar, while pressing up on the bottom of the Plug, until the Power Bar clicks into place (Fig. 2). 2. Align Light Engine with Blade Mount Hanger (Fig.
June 10, 2019 Luminaires and Luminaire Hangers Assembly Instructions INSTRUCTIONS D’INSTALLATION Mezzaluna Luminaire: Applies to Components: 1. Align Luminaire with Power Bar 1XDXXCH06x (Fig.1), press down firmly on the top of the Luminaire, while pressing up on the bottom of the Power Bar, until the Power Bar clicks into place (Fig. 2). 2. Mezzaluna Luminaires can be assembled on top or on the bottom of the Power Bar.
June 10, 2019 Suspenders Precise Trim Kits TM Assembly Instructions INSTRUCTIONS D’INSTALLATION Power Precise Round Trims: Applies to Components: 1. Align the Lens, Shade, and 1XZ0202xxx 1XZ0205xxx Bezel with each other (Fig. 1XZ0203xxx 1XZ0206xxx 3) then preassemble them together (Fig. 4). 2. Align the assembly from step 1 with the Light Engine (Fig. 5). 3. Screw the assembly from step 1 to the Light Engine (Fig. 5).
June 10, 2019 Suspenders Precise Trim Kits TM Assembly Instructions Applies to Components: 1XZ03010xx 1XZ03020xx INSTRUCTIONS D’INSTALLATION 1XZ03030xx Power Precise Square Trims: 1. Align Trim with Light Engine, make sure to align the Notch found on the Trim to the Set Screw found on the Light Engine (Fig. 1). 2. Insert the Trim into the Light Engine (Fig. 2). 3. Secure the Trim by screwing in the Set Screws (Fig. 3). Light Engine Set Screw Notch Fig. 2 Fig. 3 Fig.
Component Index Item Number Page 1XC02XX12x . . . . . . . . 2 1XC02XX24x . . . . . . . . 2 1XC01XX12x . . . . . . . . 2 1XC01XX24x . . . . . . . . 2 1XC01XX36x . . . . . . . . 2 1XC01XX48x . . . . . . . . 2 1XC01XX72x . . . . . . . . 2 1XC01XX96x . . . . . . . . 2 1XB01SC06x . . . . . . . . 3 1XB01SC20x . . . . . . . . 3 1XB01RC06x. . . . . . . . 3 1XB01RC20x. . . . . . . . 3 1XB01DC06x. . . . . . . .
June 10, 2019 Power Feed Installation Assembly Instructions INSTRUCTIONS D’INSTALLATION Important • Always disconnect the power before installing or replacing components and before cleaning or other maintenance. • Consult a qualified, licensed electrician to ensure correct branch circuit conductor. Consulter un électricien qualifié pour vous assurer que les conducteurs de la dérivation sont adéquats. Deep Power Feed Installation (Fig. 1): Applies to Components: 1. Shut off power to the outlet box.
Suspenders® - Double Ring Configuration June 10, 2019 Assembly Instructions INSTRUCTIONS D’INSTALLATION Important • Always disconnect the power before installing or replacing components and before cleaning or other maintenance. • Consult a qualified, licensed electrician to ensure correct branch circuit conductor. Consulter un électricien qualifié pour vous assurer que les conducteurs de la dérivation sont adéquats.
