One Guides One
Overview The smart speaker for music lovers— Perfect fit for shelves, counters, and snug spaces or mounted to a wall, ceiling, or speaker stand. Freedom of control using the Sonos S2 or Sonos S1 app, the touch controls on the speaker, or your voice. Pair two Sonos Ones for left-right stereo sound, or use two Sonos Ones as rear surrounds for your home theater. See Setup when you’re ready to add a Sonos One to your system.
Control and lights Volume up (right) Volume down (left) Touch and hold to quickly Volume Control change the volume. Note: You can also use the Sonos app and voice control to adjust volume. Press once to play or pause audio. Play/Pause Press and hold to add the music that’s playing in another room. Swipe right to skip to the next song. Swipe left to go to the Next/Previous previous song. Note: You can’t skip forward or go back when listening to a radio station.
Tap to turn the microphone on or off: When the microphone light is on, voice control is on and your voice service is ready to respond. When the light is off, Microphone voice control is off. Note: If you’ve installed a voice service and the microphone is off, you can still use voice commands. Just press and hold — no need to start with a wake word. When you release the microphone button, voice control turns off again.
Connector panel 1 Join button Press to connect to your Sonos system during setup. 2 Ethernet port Use an Ethernet cable if you want to connect to a router, computer, or network-attached storage (NAS) device (optional). 3 AC power (mains) input Use only the supplied power cord (using a third-party power cord will void your warranty). Note: Insert the power cord firmly until it is flush with the bottom of the speaker.
Select a location You can put your speaker just about anywhere. For maximum performance, here are a few guidelines: Sonos One sounds great even when placed next to a wall or on a shelf. For best performance, leave at least 1" (2.5cm) space around the back of the speaker. It’s humidity-resistant so you can use it in the bathroom. It’s not water-resistant so don’t put it near water or leave it in the rain. Set up stereo pair Pair two Sonos speakers in the same room for a wider, stereo experience.
Set up surrounds It’s easy to turn two Sonos speakers (same model), or a Sonos Amp and your favorite nonSonos speakers, into separate right and left channels for your home theater. 1. Place each surround speaker about 10ft from your favorite listening position, angling them toward the seating area. 2. Go to > System. 3. Select a room with a soundbar and choose Add Surrounds to get started. Note: If you group the rooms or create a stereo pair instead, you won't have surround sound.
Voice services Use your voice to control your Sonos system with any voice-enabled Sonos product—play and control content, turn the volume up or down, and more. Sonos Voice Control: control your whole Sonos system with hands-free ease and unmatched privacy. Sonos Voice Control comes ready to use—it only takes a few seconds to add when you set up your speakers. More information Amazon Alexa: you’ll need the Sonos app and the Alexa app with the Sonos skill enabled.
Trueplay™ Every room is different. Trueplay tuning measures how sound reflects off walls, furnishings, and other surfaces in a room, then fine tunes your Sonos speaker to make sure it sounds great no matter where you've placed it. Trueplay works on iOS mobile devices running iOS 8 or later. During tuning, you'll move around the room holding your mobile device. 1. Select > System, and pick the room you want to tune. 2. Choose Trueplay Tuning to get started.
Product settings You can customize Sonos products for your surroundings. Go to > System and select a product. Room Name If you move your speaker to a new room, you can change its name in Settings. You can turn off your speaker’s WiFi when it’s connected to your network with an Ethernet cable. This reduces power Turn off WiFi (not available for portable products) consumption and can improve connectivity for some wired speakers.
Displays the speaker’s connection to WiFi, indicates when the volume is muted, and Status Light signals errors. Learn more Note: If the light is distracting, you can turn it off in Settings. You can disable the touch control on your speaker. You may want to do this to Touch Controls prevent a child or curious pet from accidentally adjusting playback or volume.
When a projector, turntable, stereo, or other audio device is connected to a Sonos product, you can adjust these linein settings: Source name: Choose a name for the line-in device. Source level: Adjust the line-in source level if you find the default volume Line-In (for Sonos products with line-in capability) setting is too quiet or distorted. Audio Delay: Add a delay between the line-in source and Sonos to reduce the chance of audio issues occurring when you're playing line-in audio on grouped speakers.
Sonos One Stand A set of custom-designed stands for Sonos One, One SL and Play:1 speakers provides an elegant solution for placing your home theater surrounds. Indentation in the stem hides the speaker’s power cable for simple cable management. Solid construction. The base has increased structural stability to eliminate wobbling, and bumpers secure your speakers in place. Perfect height for home theater surrounds. Dimensions (H x W x D): 32.98 x 11.81 x 11.81in. (837.8 x 300 x 300mm) Weight: 12.3lbs (5.
Set it up 1 Take everything out of the box and place the base in the packaging slot to stabilize it for the next few steps. Unplug your Sonos speaker, and thread the speaker end of the power cord through the opening in the base. 2 Insert the stem snugly into the base, using the alignment pins to position the power cord channel either in the front or back. Use the 2 black screws and a Phillips-head screwdriver to attach the base. 3 Route the speaker’s power cord through the speaker platform.
4 Use the 2 silver screws to attach the speaker platform to the top of the stem, threading the power cable carefully. Snap the bottom plate on with the power cable channel in the back, and mount the platform on the stem. 5 Plug the power cord back into the speaker and place on the top mount, pulling any extra cable down from the top. Tighten the screws and attach the top cap with the notch facing toward the speaker. 6 Press the power cord into the stem, working from top to bottom.
7 Tilt the Stand forward slightly to wrap the excess cord around the bottom of the base.
Sonos One Shelf The easy-to-install shelf for Sonos One, One SL and Play:1 securely holds your speaker in place—its space-saving design provides a designated space for your speaker. Designed to support up to 8lbs (3.6kg). Dimensions (H x W x D): 0.89 x 10.23 x 6.29in.(22.7 x 260 x 160mm) Weight: 1lb (0.45kg) Note: For the full selection of Sonos-compatible stands, wall mounts, and cables, see Accessories on our website.
Wall material Hard wallboard or double board Plaster Concrete or brick Pre-drill Use wall anchors Use screws 5/16” / 8 mm bit Yes Yes 5/16” / 8 mm bit Yes Yes 5/16” / 8 mm bit Yes Yes
Set it up 1 Place the wall bracket against the wall and mark the screw holes. (Make sure the black bracket foam ring is face up.) 2 If using wall anchors, use a 5/16" drill bit to drill 2 pilot holes and then insert the wall anchors. Refer to the wall mounting information below for guidelines. Otherwise skip this step. 3 Use a Phillips-head screwdriver or a power drill to screw the bracket to the wall.
4 Position the Shelf the way you want it (supports left or right speaker placement). Press the Shelf firmly on to the wall bracket until it snaps into place (both front and back). 5 Route the speaker’s power cord through the Shelf opening. (You’ll wrap the cord around the bottom of the Shelf after it’s assembled.) 6 Carefully align the pins, then press the bottom cover firmly onto the shelf until it snaps into place. Plug the power cord into the speaker and place it on top of the Shelf.
7 Wrap the excess power cord around the bottom of the Shelf.
Sonos One Mount The easy-to-install mount for Sonos One, One SL and Play:1. Holds speaker normally, upside-down, or even horizontally. Speaker can pivot up to 45 degrees. Allows access to ports, buttons, and touch controls. Cleanly routes your speaker’s cables. Important: This mount is intended for use only with Sonos One, One SL, and Play:1. What's in the box? Mount Wall bracket Top cap Mounting kit Note: Sonos speakers sold separately.
Wall mount Pre-drill Use wall anchors Use screws 5/16” / 8mm bit Yes Yes Plaster 5/16” / 8mm bit Yes Yes Concrete or brick 5/16” / 8mm bit Yes Yes Hard wallboard or double board
Set it up 1 Place the wall mount bracket against the wall using a level to make sure it is vertical and mark the screw holes. 2 If you're using wall anchors, use a 5/16" drill bit to drill 2 pilot holes and then insert the wall anchors. 3 Use a Phillips-head screwdriver or power drill to screw in the wall mount bracket. 4 Feed the speaker's power cord through the Mount opening and plug it into the speaker. Place it down onto the Mount.
5 Press the top band down firmly onto the speaker and use a Phillips-head screwdriver to screw in the top band fastener on the back. 6 Slide the Mount down onto the wall bracket. 7 Twist the speaker to position it in place, then turn it right to lock it in securely. Turn left to unlock. 8 Route the power cable into the side hook and plug the speaker into power.
Specifications Feature Description AUDIO Amplifier Tweeter Two Class-D digital amplifiers. One tweeter creates a crisp and accurate high frequency response. One mid-woofer ensures the faithful Mid-woofer playback of mid-range vocal frequencies plus deep, rich bass. Turn two speakers into separate left and Stereo pair right channel speakers to create wider, deeper sound. Home theater Add two speakers as surrounds for a true surround sound experience. Far-field microphone array.
Feature Description NETWORKING* Using Sonos S2: Connects to WiFi network with any 802.11a/b/g/n 2.4 or 5GHz broadcast-capable router. Using Sonos S1: Connects to WiFi Wireless connectivity network with any 802.11b/g 2.4GHz broadcast-capable router. 802.11n only network configurations are not supported —you can either change the router settings to 802.11b/g/n or connect a Sonos product to your router. One 10/100Mbps Ethernet port.
Feature Description Storage temperature -4° to 158°F (-20° to 70°C) Designed to withstand high humidity, like Humidity resistant in a bathroom with a running shower. (It is not waterproof or water-resistant.) Product finish Package contents * Specifications subject to change without notice.
Important safety information 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry soft cloth. Household cleaners or solvents can damage the finish on your Sonos products. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat.
