3-864-804-11 (1) Digital Portable Cellular Telephone Operating Instructions CM-Z200 1_CM_Z200 1 6/8/98, 9:26 AM
Welcome to the CM-Z200 Menu map Saved #s display Standby display + SAVED #S :Calls List :Phone Book :Find Name or – It's a Sony! 12:34P 12/25 :Saved #s :Features + – List 10 most recent calls •Options -Send -Prefix -Duration -Time/Date -View Number -Number Tone -Save Find name in Phone Book List up to 99 saved numbers in Phone Book •Options -Send -Prefix -Edit -Restriction -View Number -Number Tone -Erase FEATURES •Message -Voice* -New Text* -Old Text* -Erase Old* •Sounds -Ringer Volume -Mute/Un
Easy dialing You can easily make a call using a number from the Phone Book or the Calls List. First, turn the Jog Dial either up or down one time to search phone numbers. Then scroll down to view saved numbers in the Phone Bookor scroll up to view your most recently called numbers in the Calls List. Simply open the arm microphone to call the number you choose. No.
Before operating the CM-Z200 portable cellular/PCS telephone, please read this manual thoroughly and retain it for future reference. If your usage includes invehicle operation, it is recommended that you refer to the Installation/Connections/ Operation manual for the optional accessory kits. DISPOSAL OF LITHIUM ION BATTERY LITHIUM ION BATTERY. DISPOSE OF PROPERLY. You can return your unwanted lithium ion batteries to your nearest Sony Service Center or Factory Service Center.
Table of contents Unpacking your phone ..................................................................................................... 2.1 Looking at your phone ..................................................................................................... 2.2 Charging the battery pack ................................................................................................ 2.4 Basic Calling Operations Turning the phone on ................................................................
Rules and regulations The U.S. Federal Communications Commission and the Industry Canada regulate cellular/PCS telephone service in their respective countries. It is important for you, the cellular/PCS telephone user, to observe the applicable regulations when operating your cellular/PCS telephone in either country. In addition to these U.S.
Safety precautions IMPORTANT For safe and efficient operation of your phone, observe these guidelines. Your dual mode (analog/digital CDMA) hand-held portable cellular/ PCS telephone uses both analog frequency modulation (FM) technology and digital Code Division Multiple Access (CDMA) technology. CDMA is a newer radio frequency (RF) technology than the FM technology that has been used for radio communications for decades. Your dual mode portable cellular/PCS telephone is a radio transmitter and receiver.
Antenna care and replacement Medical devices Do not use the phone with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Replace a damaged antenna immediately. Take your phone to an authorized service center for repair. Consult the manufacturer of any personal medical devices (such as pacemakers, hearing aids, etc.) to determine if they are adequately shielded from external RF energy. Your physician may be able to assist you in obtaining this information.
Blasting areas To avoid interfering with blasting operations, turn your unit OFF when in a “blasting area” or in areas posted: “Turn off two-way radio.” Construction crews often use remote control RF devices to set off explosives. Potentially explosive atmospheres Turn your phone OFF when in any area with a potentially explosive atmosphere. It is rare, but your phone or its accessories could generate sparks. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death.
(this page intentionally left blank) 1.
Unpacking your phone CM-Z200 Telephone (1) QN-029BPL Li-Ion Battery Pack (1) Hand Strap (1) QN-001AC AC Adapter (1) Note: Different AC adapters may be provided outside North America. Attaching the hand strap 1 2 2.1 2_CM_Z200 1 6/8/98, 9:26 AM Getting Started Carefully unpack your phone and check the contents using this list. If there is something missing, please contact your nearest Sony dealer.
Looking at your phone For further information, refer to the page numbers indicated in parentheses ( ). !º 1 2 !¡ !∞ 5 3 4 !¢ 1 4 GHI 7PQRS 2 ABC 5 JKL 8 TUV 0+ 6 3 DEF 6 MNO 9WXYZ !™ SEND 7 CLR END PWR 8 !£ 9 8 TUV 0+ NO 9 WXY CLR END PWR !§ Telephone 1 Call alert indicator (XX) Lights when there is an incoming call. 8 END button (XX) Press to end calls. Also cancels operations and returns the phone to standby mode. 9 PWR (power) button (XX) Press to turn the phone on or off.
The top row of the display contains icons that inform you of the current status of your phone. The bottom four rows of the display are for text such as phone numbers, names, and operational prompts. Each row displays a maximum of 12 characters. 1 23456 7 888 8 1 Short character display Shows settings such as the number of the currently displayed Menu, as well as Phone Book and Calls List memory locations. 2 (in-use) / (out-of-service) icon (XX, XX, XX) The in-use icon appears during a call.
Charging the battery pack Charge the battery before using the phone. A new battery is not fully charged. To charge the battery, attach the battery pack to the phone, then connect the supplied AC adapter. Attaching the battery pack 1 Hook the battery pack onto the top of the phone 1, and ease the battery pack down 2. 2 Snap the battery pack in place. To remove the battery pack 1 Push the battery pack release tab upwards. 2 Lift up the bottom of the battery pack 1, and pull it out 2. 2.
Connect the AC adapter to the phone and the other end to a standard AC outlet as illustrated below. The charging time is approximately 3.5 hours. You can charge the battery pack with the phone turned on, but charging will take longer. to an AC outlet display to the connector on the phone (the thumb indent should face upwards) When the power is turned on As the battery pack charges, the battery icon ( ) indicates that the phone is charging.
Checking the battery CDMA mode Analog mode In standby mode 40 hours 11 hours In use continuously 2.3 hours 1 hours Battery condition The battery icon indicates the battery level as follows (when the power is on): Full n n n n n Empty Note that the battery icon displays the approximate charge level and that the consumption may vary depending on conditions of use, such as ambient temperature, network coverage, and usage patterns.
Turning the phone on To use your phone, the power must be turned on. It is preferable to extend the antenna, since this maximizes signal strength and minimizes interference. Pull up Call alert Extending the antenna Hold the end of the antenna and pull up until fully extended. Push the antenna down until it is fully retracted. Turning the power on Hold down PWR for about one second. The call alert indicator lights up, a beep sounds, and the phone starts searching for a signal.
Making calls You can call any number up to 32 digits from within a service area. The out-of-service icon ( ) indicates that you are outside the service area. Arm mic CLR SEND 0OPER - 9 WX YZ / END 1 Use the number buttons to enter the number. If you enter the wrong digit, press CLR to back up. To clear all entered digits, press END or hold down CLR to return to the standby display. 2 If the arm microphone is closed, open it to dial. If the arm microphone is open, press SEND to dial.
Receiving calls You can receive calls as long as the out-of-service icon ( ) is not displayed. The icon indicates that you are outside the service area. Arm mic CLR SEND When you receive a call, the ringer sounds or the phone vibrates. Incoming Call flashes on the display, and the call alert indicator blinks. 1 If the arm microphone is closed, open it to answer the call. If the arm microphone is open, press any button except the call.
Storing phone numbers in the Phone Book Your phone features a built-in Phone Book memory, in which you can store up to 99 (01–99) phone numbers with names. You can dial stored numbers quickly by recalling them from the Phone Book (see page XX). CLR YZ 0OPER - 9 WX / Each phone number can contain up to 32 digits, and each name up to 12 characters. This section shows how to store, edit, and erase Phone Book numbers quickly. 1 On the standby display, use the number buttons to enter the number.
Alphanumeric table (English) Each time you press a number button, the letters/numbers appear as follows: Button Sequence 1 – “ 2ABC A B . C ‘ a , & d e 3DEF D E F 4GHI G H I g K L 5JKL J M 7PQ RS P Q R S 8TUV T U 9 WX YZ W 0OPER 0 X ) : 1 2 f 3 h i 4 6MNO j k N O ( b c l 5 m n o 6 p q V t u Y Z w v r s 7 8 x y z 9 Tip When you change your phone’s language setting (see page XX), a different set of characters becomes available.
To enter Select The display shows a hard pause Hard Pause H a time pause Time Pause T a link Enter Link L a hyphen Enter Hyphen – If the Phone Book is full If there are no memory locations available, a message indicates that the memory is full. After entering a name, a message prompts you to specify a memory slot to overwrite. To cancel, hold down or just press CLR .
7 Enter the new information. Enter new information the same way you stored original information (see page XX). The old information is overwritten. 8 When you are finished, push . A message confirms that your changes have been saved. Tip In addition, you can use the Directory menu to edit Phone Book numbers (see page XX). Erasing a phone number You can erase stored Phone Book entries. If the selected entry is restricted, you must enter the four-digit lock code before you can erase it (see page XX).
To unrestrict an entry 1 Select the Phone Book entry that you want to unrestrict. The message indicates a restricted entry. 2 Push . The Options menu appears. 3 Turn to select Restrict, then push . A message appears, prompting you to enter the lock code. (See page XX for information on lock codes.) 4 Use the number buttons to enter the lock code. Now the selected entry is unrestricted. After a few seconds, the standby display reappears.
Calling from the Phone Book You can dial frequently used numbers quickly from the Phone Book using the Jog Dial navigator. Also, by using speed/touch dialing, you only need to press a few buttons to dial. Arm mic SEND YZ 0OPER - 9 WX / 1 On the standby display, turn once. The Saved #s display appears. 2 Turn – down to select Phone Book. The first entry in the Phone Book appears. 3 Turn to select the desired Phone Book entry. The contents of the selected entry are displayed.
Speed dialing To dial quickly, you can enter the Phone Book memory location numbers. The phone calls the number stored in the corresponding location. 1 Use the number buttons to enter the memory location number. 2 To dial the number, open the arm microphone. If the arm microphone is already open, press SEND . The phone dials the number that corresponds to the memory location you entered. Touch dialing You can dial a phone number stored in the Phone Book without pressing SEND .
Searching the Phone Book To locate a desired Phone Book entry, you can search by name, phone number, or memory location. You can search the Phone Book either alphabetically or for a string of characters. Searching alphabetically When you enter only one character, the phone lists all entries that begin with the entered character. 1 From the standby display, turn once. The Saved #s display appears. 2 Push . The Search display appears. 3 Enter only the first letter of the name you want to find. 4 Push .
4 Push . The entries containing the selected string are displayed starting from the lowest memory location number. 5 Turn to view the next entry in the search string. Note If the search string does not contain punctuation or a space, the phone scans only the first characters of the words in the matching entries. Searching by memory location The phone searches for a memory location that matches the entered digit(s), and displays a list of options.
Calling from the Calls List Information on the ten most recent outgoing calls, incoming calls, scratch pad entries, and missed calls are stored in the phone’s Calls List. If you call the same number twice in a row, only the most recent call is stored in the Calls List. Arm mic SEND YZ 0OPER - 9 WX / 1 On the standby display, turn once. The Saved #s display appears. 2 Turn + up to go to Calls List. Information on the most recent call appears. 3 Turn to select the entry you want.
Sending DTMF signals from the Phone Book You can send DTMF (Dual Tone Multiple Frequency) signals to access electronic services (such as telephone banking) when dialing numbers from the Phone Book. YZ 0OPER - 9 WX / Dual Tone Multiple Frequency is also known as “touch-tone.” A tone is generated when you press a telephone button (number, *, or #). It can be used to access answering machines, pagers, telephone banking services, data services, and other electronic services.
(this page intentionally left blank) 4.
About the Features menu You can use the Features menu to activate the special features of your phone. For a list of submenus and settings, see “List of menu items” on page XX or “Menu map” on page XX. Several features on the Features menu are dependent on your service provider and the network your phone is operating on. Network-dependent features are marked with an asterisk (*) on page 1.2 and pages 6.X-6.X. Check with your service provider to see if these features are available in your area.
Messages This section contains information on the Short Messaging Service (SMS). This feature may allow you to receive voice or text messages. Contact your service provider to see if this service is available in your area. CLR SEND END Receiving messages To receive messages, the phone must be turned on.
If the memory becomes full The phone issues a warning when the memory is 75% full. At this point, you should erase expendable messages (see page XX). If the memory becomes completely full or your phone does not have enough memory to receive an incoming message, new messages are rejected. Accessing messages 1 Push twice from the standby display. The Message menu appears, indicating the number of the following types of messages, respectively: • Voice mail messages (see page XX).
To erase a voice message 1 After reading a voice mail notification message, push . The Options menu appears. 2 Turn to select Erase Msg, then push . The voice mail notification message is erased. The Message menu reappears, indicating that there are currently no voice mail notification messages stored in memory. Reading new text messages [F12] You can read both new and old messages stored in memory. Urgent messages are listed above non-urgent ones, with the most recent entries first.
2 Turn to scroll through the list of old messages. 3 To read the selected message, push . The selected message is displayed. 4 Turn to scroll through the message. If you do not scroll, the display automatically scrolls down to the end of the message, which is indicated with a hollow box ( ). 5 When you have read the message, press CLR to return to the list of old messages. To read the next message, push to go to the Options menu, then select Next Msg.
To save the callback number 1 After reading a message, push . The Options menu appears. 2 Turn to select Save Number, then push . A message appears, prompting you for a name to accompany the number. 3 Use the number buttons to enter the name. If you press the same button in quick succession, the letter you just entered changes. (See the “Alphanumeric table” on page XX.) Use / or to move the cursor and to insert spaces between characters.
Sounds You can adjust the volume of the ringer, keybeep, and earpiece on the Sounds menu. In addition, you can select the type of sounds heard when the phone rings and when you press buttons. (See page XX for instructions on how to reach the Sounds menu.) Adjusting the ringer volume [F21] 1 Push to select Ringer Vol from the Sounds menu. The Ringer Vol. menu appears. 2 Turn up to raise the ringer volume, and down to lower it. You can select from six ringer volume settings: off, low, med.
Adjusting the keybeep volume [F23] You can adjust the volume of the beep that sounds when you press a button. 1 Turn to select Keybeep Vol from the Sounds menu, then push . The Keybeep Vol menu appears. 2 Turn up to raise the keybeep volume, and down to lower it. You can select from four keybeep volume settings: off, low, med. (medium), and high. 3 Push to enter the new setting. The standby display reappears.
Setting the keybeep type [F26] You can set the beep that sounds when you press a button to either a tone or a click. Tones sound similar to DTMF tones, and clicks are indicated by single beeps. 1 Turn to select Key Sound from the Sounds menu, then push . The Key Sound menu appears. 2 Turn to select the keybeep type. You can select tones or clicks. 3 Push to enter the new setting. The standby display reappears.
Timers You can check call durations on the Timers menu. In addition, you can set the phone to alert you every minute of a call, and make the phone turn itself off automatically. Checking the duration of all calls [F31] You can view the total duration of all calls. This information cannot be reset. 1 Turn to select All Calls from the Timers menu, then push . The All Calls display appears. 2 Push to go back to the standby display.
Setting the minute alert [F34] You can set the phone to alert you ten seconds before every full minute. 1 Turn to select Minute Alert from the Timers menu, then push . The Minute Alert menu appears. 2 Turn to select the desired alert time. You can select from four settings: off, before min, each min, and every 5 min. If you select before min, the phone alerts you 10 seconds before every full minute. 3 Push to enter the new setting. The standby display reappears.
Directory You can use the Directory menu to check your phone number, as well as store, erase, and edit phone numbers and names in the Phone Book. Also, you can use this menu to view the Calls List. Checking your phone number [F41] 1 Push to select My Number from the Directory menu. The My Phone # display appears, showing your phone’s number. 2 Push to exit this feature. The standby display reappears.
Erasing a phone number [F43] You can erase stored Phone Book entries. If the selected entry is restricted, you must enter the four-digit lock code to erase it (see page XX). 1 Turn to select Erase from the Directory menu, then push . A message appears, prompting you for the Phone Book entry to be erased. 2 Turn to select the entry you want to erase, then push . A message appears, prompting you to confirm that the selected Phone Book entry should be erased.
6 When you are finished, push . The Options menu reappears when you edit the phone number. New information is saved when you edit the name or memory location. 7 Turn to select Save, then push . A message appears, confirming that your changes have been saved. Tip In addition, you can use the Options menu to edit Phone Book entries (see page XX). Searching the Phone Book by name [F45] You can find name entries in the Phone Book by searching alphabetically or for a string of characters.
Searching the Phone Book by memory location [F46] You can find memory locations easily. 1 Turn to select Phone Book from the Directory menu, then push . A message appears, prompting you for a search string. 2 Use the number buttons to enter the memory location number. The Phone Book entry that matches the search string is displayed. If the selected entry is empty, the display shows the message Phone Book storage location XX is empty. After a few seconds, the standby display reappears.
Extras On the Extras menu, you can set the phone to enable touch dialing, redial automatically, and answer incoming calls automatically or at the press of any button. Also, you can use this menu to lock the keypad and to jot down phone numbers. Preventing accidental operation [F51] When the microphone is closed, you can lock the keypad by pushing and holding from the standby display. You can also lock the keypad from the Features menu, as described below. Locking the keypad offers low-level security.
Setting the phone to redial automatically [F53] You can set the interval for redialing. If the attempt to dial is not successful, the phone tries to redial it up to five times every three seconds. 1 Turn to select Auto-Retry from the Extras menu, then push . The Auto-Retry menu appears. 2 Turn to select on or off. If you select off, the phone does not try to redial automatically. 3 Push to enter the new setting. The standby display reappears.
Security You can restrict unauthorized access to your phone and the information it holds. Also, on the Security menu, you can reset menu settings to default and store emergency numbers. Unlike other items on the Features menu, accessing the Security menu requires a lock code when you select it from the menu. A typical default lock code is either the last four digits of your phone number or 0000. Preventing others from using your phone [F61] This option lets you set when the phone will be locked.
Restricting a Phone Book entry [F63] You can restrict access to individual Phone Book entries. 1 Turn to select Restrict # from the Security menu, then push . A message appears, prompting you to specify Phone Book entry to restrict. 2 Turn 3 Push to select the Phone Book entry that you want to restrict. to restrict the selected entry. Now the selected entry is restricted. To unrestrict an entry To select the entry you want to unrestrict, follow the procedure above for restricting an entry.
Reverting to default settings [F65] You can reset all menu settings to the defaults. This does not affect Phone Book or Calls List entries. 1 Turn to select Master Reset from the Security menu, then push . The Master Reset display appears. 2 Press 1 to revert to the factory defaults, or push current settings. to keep the If you revert to the factory defaults, all your custom menu settings are erased. Erasing all Phone Book entries [F66] You can erase all Phone Book entries at once.
Storing emergency numbers [F68] You can use the Security menu to store up to three emergency numbers other than 911 (which you cannot erase). You can call these numbers even when the phone is locked. 1 Turn to select Emergency # from the Security menu, then push . The first Emergency # display appears. 2 Turn to select the emergency memory location, then push . A message appears, prompting you to enter the phone number for the emergency entry. 3 Use the number buttons to enter the number.
Display You can use the features on the Display menu to change the appearance of the onscreen display. Setting the banner [F71] You can change what the banner reads. 1 Push to select Banner from the Display menu. The Banner display appears. The current banner text is displayed. 2 Push again to start editing. A message appears, prompting you to enter a new banner. 3 Use the number buttons and / or to enter the new banner text. The banner can be up to 12 characters long.
Setting autohyphenation [F73] You can turn the autohyphenation feature on and off. If you turn it on, entered numbers are hyphenated according to the US/Canada standard (eleven digits which include a long distance identifier, an area code, a three-digit community code, and a four-digit location code, for example, 1-800-555-1212). 1 Turn to select Auto-Hyphen from the Display menu, then push . The Auto-Hyphen menu appears. 2 Turn 3 Push to select on or off. to enter the new setting.
Setting the menu length [F76] You can set the menu length (long or short). The short menu displays only the most common items on the Features menu; the long menu displays all items. 1 Turn to select Menu Length from the Display menu, then push . The Menu Length menu appears. 2 Turn to set the menu length. You can select short or long. 3 Push to enter the new setting. The standby display reappears.
Network On the Network menu, you can set the phone to alert you when the roaming status changes, when a call is dropped, or when enhanced voice privacy is lost. Setting the roaming alert [F81] Your phone is roaming when you use it outside of the home area. Roaming access to a different carrier and the types of calls you can make varies with the agreement between your “home” carrier and the currently serving carrier. Check with your service provider for details about roaming in a specific area.
Setting the voice privacy alert [F83] Some networks and service providers offer a voice privacy feature. This feature encrypts transmissions to and from you phone for added privacy. A display appears to indicate if enhanced voice privacy is lost during a call. You can choose to have an audible alarm accompany this display. 1 Turn to select Priv. Alert from the Network menu, then push . The Priv. Alert menu appears. 2 Turn 3 Push to select on or off. to enter the new setting.
Selecting system priority [F85] If you leave the service area of a carrier from which the phone is currently receiving signals, the phone automatically starts searching for another carrier. You can control the order in which the phone searches for a carrier. 1 Turn to select Set System from the Network menu, then push . The Set System menu appears. 2 Turn to set the preferences. You can select standard, home side, roam side, or home only.
(this page intentionally left blank) 5.28 5.
Troubleshooting Problem Cause/Remedy Page Nothing appears on the display. • The phone is off. Turn the phone on. • Battery is fully discharged. Recharge the battery. 20 17 The out-of-service icon ( ) appears. • The phone is outside the service area, or the signal is too weak. Extend the antenna fully. 21 Nothing happens when you press the buttons. • The buttons may be locked. • The phone may be locked. Enter the lock code to unlock the phone. 69 74 The call does not go through.
Accessories Supplied accessories QN-029BPL Li-Ion Battery Pack (1) QN-001AC AC Adapter (1) (other AC adapters may be provided outside North America) Hand strap (1) Optional accessories QN-008CLA Rapid Charging Cigarette Lighter Adapter QN-009TA Travel Adapter QN-012DAS Interface Cable and FoneBook™ PLUS Software QN-020TCL Combination Travel Adapter/Cigarette Lighter Adapter QN-021BCD Dual Slot Battery Charger QN-023DCS Desktop Charger Speakerphone QN-024HC Auto Travel Holder QN-025PHK Portable Hands-Free Ca
Specifications Frequency range Transmit: 824 to 849 MHz Receive: 869 to 894 MHz Dimensions 3.6 × 2.4 × 1.0 inches (h/w/d) (not including antenna) (91 × 62 × 26 mm) Mass (weight) Approx. 5.3 oz (150 g) (including battery) RF power output CDMA mode: 0.01 µW to 200 mW AMPS mode: 6 mW to 600 mW Operational temperature –22°F to +140°F (–30°C to +60°C) (excluding battery pack) Additional Information Design and specifications are subject to change without notice. 6.
List of menu items This section lists the Features menu and its submenus. You can use the Features menu to activate the special features of your phone. Menu Item Settings F11 Voice* F12 New Text* F13 Old Text* F14 Erase Old* F21 Ringer Vol.
Menu Item Settings F61 Lock Phone F62 New Code F63 Restrict # F64 Restrict All F65 Master Reset F66 Erase Book F67 Erase Calls F68 Emergency # F71 Banner* F72 Backlight F73 Auto-hyphen F74 Sort Book F75 Language* F76 Menu Length F77 Msg. Format* F81 Roam Alert F82 Drop Alert* F83 Priv.
Glossary A E Automatic answer ESN Feature that automatically answers calls. Electronic Serial Number. The unique identification number of your telephone. The telephone transmits this number to the base station every time a call is placed. Automatic retry Feature that automatically redials a call when a “System Busy” indication is received. B Banner Message at the top of the standby display. Emergency number In addition to the general emergency number (911 for the U.S.A.
N S NAM Scratch pad Number Assignment Module. Portion of your telephone’s memory programmed to contain information about your subscription to the carrier. Your telephone can have up to two NAM’s. Allows you to enter a number and store it in the Calls List. Service area Region covered by a PCS service. Also see “Coverage area.” SMS P Pause You can enter pause codes in the phone number memory data. Use this feature when accessing an answering machine, voice mail system, electronic banking system, etc.
Index A Display settings Accessing 44 Autohyphenation 80 Backlight 79 Banner 78 Time 60 Displays Calling 23 Menu 21 Hyphens/pauses/links 30 Menu setting 82 Security 73 Standby 21 Dropped call 84 DTMF (Dual Tone Multiple Frequency) 43 AC adapter 11, 17 Antenna 20 Arm microphone 12 Automatic Answer 71 Hyphenation 80 Retry 70 Redial 70 B Backlight 79 Banner 78 Battery pack Charging 16 Checking 19 Attaching/removing 16 Battery charge contacts 17 Battery pack release tab 13 Battery icon 15, 17 E C Calling C
I P Incoming call 25 In-use icon 23, 25 Pause 30 Phone Book 27, 35, 38, 62 Power Turning off 21 Turning on 20 Prefix 4.6 K Keybeep 58 L Laws Rules and regulations 4 Lock code 74 Q M Receiving Calls 25 Messages 46 Voice mail 48 Recent number memory Calling recent numbers 41 Clearing call memory 76 Redialing Auto retry 70 Last dialed number 24 Restriction 34, 74 Ringer Volume 55 Roam 83 Roam icon 83 Roaming agreement 83 Rules and regulations 4 Quitting.
Sending. See Calling Service area 83 Signal strength icon 20 Special characters 29 Standby display 21 System settings Accessing 83 T Text Message. See Messages Touch dialing Enabling 70 Troubleshooting 88 Turning phone on 20 V Voice mail notification Accessing 47 Receiving 48 Voice Privacy 85 Volume Adjusting 55 6.
SONY Wireless Hotline Number (USA only) If you have any questions or comments, please call: SONY WIRELESS HOTLINE 1-800-578-SONY (7669) © 1998 Sony Electronics Inc. All rights reserved. Reproduction without written consent expressly prohibited. Sony and Jog Dial are trademarks of Sony. All other trademarks are the property of their respective owners. Design and specifications are subject to change without notice. Talk and standby times are subject to change. Printed in USA 6.
