Operating Instructions

24GB
E:\Works\5000942111\5000942111XAVAX7000UC\01GB-XAVAX7000UC\040CD.fm masterpage: Left
XAV-AX7000
5-000-942-11(1)
Sound
There is no sound/sound skips/sound cracks.
q A connection has not been made correctly.
q Check the connection between this unit and the
connected equipment and set the input selector
of the equipment to the source corresponding to
this unit.
q Installation is not correct.
– Install the unit at an angle of less than 30° in a
sturdy part of the car.
q The unit is in pause/reverse/fast-forward mode.
q The settings for the outputs are not made
correctly.
q The volume is too low.
q The ATT function is activated.
q The format is not supported.
– Check if the format is supported by this unit
(page 20).
Sound is noisy.
q Keep cords and cables away from each other.
USB playback
Items cannot be played.
q Reconnect the USB device.
q The USB port to which the USB device is
connected is not appropriate.
– Connect the USB device to the appropriate USB
port that supports the file formats (page 12).
The USB device takes longer to play.
q The USB device contains large-sized files or files
with a complicated tree structure.
Audio files cannot be played.
q USB devices formatted with file systems other
than FAT12, FAT16, FAT32 or exFAT*
1
are
unsupported.*
2
q The USB port to which the USB device is
connected is not appropriate.
– Connect the USB device to the appropriate USB
port that supports the file systems (page 12).
*1 USB devices formatted with the exFAT file system are
available only when connected to the USB1 port.
*2 This unit supports FAT12, FAT16, FAT32 and exFAT, but
some USB device may not support all of these. For
details, refer to the operating instructions of each USB
device or contact the manufacturer.
Operations cannot be performed.
q The USB mode of the device is not set to the
appropriate mode.
– Make sure that the USB mode of the device is
set to MSC or MTP mode.
q The USB port to which the USB device is
connected is not appropriate.
– Connect the USB device to the appropriate USB
port that supports the features (page 12).
BLUETOOTH
The other BLUETOOTH device cannot detect this
unit.
q Set [Bluetooth Connection] to [ON] (page 18).
q While connecting to a BLUETOOTH device, this
unit cannot be detected by another device.
Terminate the current connection and search for
this unit from the other device.
q Depending on your smartphone or cellular
phone, you may need to delete this unit from the
history of the connected smartphone or cellular
phone, then pair them again (page 8).
Connection is not possible.
q Check the pairing and connection procedures in
the manual of the other device, etc., and perform
the operation again.
The name of the detected device does not
appear.
q Depending on the status of the other device, it
may not be possible to obtain the name.
There is no ringtone.
q Raise the volume while receiving a call.
The talker’s voice volume is low.
q Raise the volume during a call.
The other party says that the volume is too low
or high.
q Adjust the [MIC Gain] level (page 15).
Echo or noise occurs during call conversations.
q Reduce the volume.
q Set [Speech Quality] to [Mode 1] or [Mode 2].
(page 15).
q If ambient noise other than the phone call sound
is loud, try reducing this noise.
– Shut the window if road noise is loud.
– Lower the air conditioner if the air conditioner is
loud.
The phone sound quality is poor.
q Phone sound quality depends on reception
conditions of the cellular phone.
– Move your car to a place where you can
enhance the cellular phone’s signal if the
reception is poor.
The volume of the connected BLUETOOTH device
is low or high.
q Volume level will differ depending on the
BLUETOOTH device.
– Reduce the volume level differences between
this unit and the BLUETOOTH device (page 12).
010COV.book Page 24 Friday, November 30, 2018 4:48 PM