User's Guide

ManualsBrandsSony Mobile Communications ManualsCell PhonesMobile Phone

Before Using the Terminal

docomo nano UIM card/microSD card slot

LTE/FOMA antenna section

Front camera lens

Earpiece/Speaker

Proximity/light sensor : Detects a face getting closer

to the touch screen during a call and turns it off to

prevent misoperation, and helps with automatic

screen brightness control.

Notification LED

Touch screen

Microphone/Speaker

Wi-Fi/Bluetooth antenna section

j O

Power key/Screen lock key/Fingerprint sensor

Volume key/Zoom key

l k

Camera key

Camera lens

Laser AF sensor

RGBC-IR sensor

Flash/Photo light

Nameplate

mark

Headset jack

Second microphone : Reduces noise to make voice

to be listened easily.

LTE/FOMA/GPS antenna section

USB Type-C jack

*1 The antenna is built into the terminal. Covering

around the antenna with your hand may affect the

quality of communications.

Part names and functions

nc d e f

s t u

o p b

Top

Bottom

Right BackLeft Front

Summary of content (11 pages)

PAGE 1
Part names and functions m nop c d e f b s t u Top q a i b Bottom j g v r k l b h Left a b c d e Front Right docomo nano UIM card/microSD card slot LTE/FOMA antenna section*1 Front camera lens Earpiece/Speaker Proximity/light sensor : Detects a face getting closer to the touch screen during a call and turns it off to prevent misoperation, and helps with automatic screen brightness control.
PAGE 2
*2 A sticker bearing the CE mark, FCC ID, IMEI information, etc. is attached. Please do not peel off the sticker or remove the nameplate. ❖Note Do not put a sticker or other material on the proximity/light sensor. ･ The back cover cannot be removed. Attempting to remove the back cover with excessive force may cause damage or malfunction. ･ The battery is built into the terminal and not removal.
PAGE 3
Inserting docomo nano UIM card 1 Remove the cover of the docomo nano UIM card/microSD card slot (P.26). 2 Pull the tray straight out from the terminal. 4 ･ 5 3 Insert the tray with the card and press it straight into the slot. Be careful about the direction to insert of the tray. Firmly press the parts until the tray is all the way in, and make sure that there are no gaps between the terminal and cover. With the IC side facing up, place the docomo nano UIM card on the tray.
PAGE 4
Removing docomo nano UIM card 1 Remove the cover of the docomo nano UIM card/microSD card slot (P.26). 2 Pull the tray straight out from the terminal. (P.32). 3 Remove the docomo nano UIM card from the tray. 4 Insert the tray into the terminal and press it straight into the slot. ･ 5 Firmly press until the tray is all the way in, and make sure that there are no gaps between the terminal and cover (P.32).
PAGE 5
Life of the internal battery Charging The internal battery is not fully charged at the time of purchase. ･ Estimated charging time (P.216) Operation time on full charge (estimate) The charging time varies by the internal battery condition or operating environment. ･ "Continuous standby time", "Continuous call time" (P.218) Continuous FOMA/3G stand-by time GSM LTE Continuous FOMA/3G call time GSM VoLTE call (voice) Stationary (Auto) : Approx. 470 hours Stationary (Auto) : Approx.
PAGE 6
Before charging It is recommended to use the AC Adapter 05 (optional) for charging. For details on the AC Adapter 05, refer to the AC Adapter 05 manual. ･ The AC Adapter 05 is compatible with 100V to 240V AC. For using the terminal overseas, a plug adapter that fits the electrical outlets in the country you stay is needed. Do not use an electrical transformer for overseas use to charge the terminal. ･ Use a compatible AC adapter or microUSB cable for charging.
PAGE 7
2 Unfold the power plug of the AC adapter and insert it into a power outlet. Then place the terminal on the desktop holder. ･ A sound to indicate the start of charging is heard, and the notification LED of the terminal turns on (P.46). ❖Note Check the terminal's connecting direction to connect correctly. Wrong connection may cause damage. ･ A terminal mounted on the desktop holder may be damaged if pressed hard against the holder.
PAGE 8
Charging with AC adapter 3 When using AC Adapter 05 (optional) for charging, do the following procedures. 1 2 Insert the microUSB plug of the AC adapter horizontally into the microUSB jack of the terminal with the engraved side (B) facing up. When charging is complete, unplug the AC adapter and then disconnect the microUSB plug horizontally from the terminal. ❖Note Check the connecting direction to connect correctly. Wrong connection may cause damage.
PAGE 9
❖Note Check the connecting direction to connect correctly. Wrong connection may cause damage. ･ Turning power on/off Turning power on 1 Press and hold O for at least 1 second. The terminal vibrates and lock screen appears after a while. ･ When you first turn on the power and " ようこそ (Welcome)" is displayed, follow the onscreen instructions to make initial settings (P.40).
PAGE 10
❖Information If the notification LED flashes red multiple times or an icon appears indicating that the battery is low when you press O with the terminal powered off, the battery is running low. Charge the terminal (P.34). ･ When SIM card lock (P.169) is set, enter PIN code on the PIN code entry screen (P.170). Canceling the screen lock ･ Turning power off 1 2 Press and hold O for at least 1 second. [Power off].
PAGE 11
Initial settings When you first turn on the power and " ようこそ (Welcome)" is displayed, follow the onscreen instructions to make initial settings, such as individual functions and services. 1 [GET STARTED]. 2 When the initial settings screen for docomo services appears, mark [Agree to all]u[Start settings]. Tap [ 日本語 (Japanese)] to change the language. ･ After this step, follow the onscreen instructions to configure the settings below, and then tap [NEXT] or [FINISH].