FLAT WIDE DISPLAY MONITOR FWD-40LX2F FWD-40LX2X FWD-32LX2F FWD-32LX2X KLH-W32 KLH-W26 PROTOCOL MANUAL 1st Edition
Table of Contents 1. Communication Parameters .......................................................... 1 2. Pin Assignment ...................................................................................... 1 3. Communication Data Format ......................................................... 1 4. General Function ................................................................................... 3 5. Picture/Sound ......................................................................................
1. Communication Parameters 3. Communication Data Format (a) Control message Communication Method RS-232C Synchronous Method Asynchronous No. Item Value Baud Rate 9600 bps 1 Header 0x8C:Control Character Length 8bit 2 Category 0xXX Parity None 3 Function 0xXX Start Bit Length 1bit 4 Data1 (Length) 0xXX Stop Bit Length 1bit 5 Data2 (Data1) 0xXX Flow Control None : : 0xXX : : 0xXX X Data (X-3) 0xXX X+1 Check Sum 0xXX 2.
(c) Answer message 1 Control answer No. Item 1 Header 2 * Answer Value No. Item Value 0x70:Answer 1 Header 0xE0:Answer 2 Answer* 0x00:No Function Error 0x00:Completed 0x01:Limit Over 0x01:Check Sum Error 0x02:Limit Under 0x02:Data Length Error 0x03:Command Canceled 3 Check Sum 4 Error answer 0xXX * 0x00:Completed Packet is correctly received and process is also correctly completed. Packet is correctly received, but the data value is over the upper limit.
4.
Code Table (1-a) [a]Function 0x18 [b]Range/Switch Code Sync Mode 0x1B Clock Display 0x24 Input Detect (Option1) 0x00 H/Comp 0x01 Video 0x00 OFF 0x01 ON 0x00 FW12 (HD15) 0x01 FW10 (VIDEO, S-VIDEO) BNC 0x02 FW11 (BNC) 0x03 Reserved 0x04 FW31/32 0x05 FW50 (RGB) 0x06 FW20 (UART + CTRL-S) 0x07 Reserved 0x08 Reserved 0x09 Reserved Command Control Enquiry Standby Power On Yes Yes Disable Enable Yes Yes Disable Enable No Yes Disable Enable No Yes Disable Enable
Code Table (1-a) [a]Function 0x32 0x35 [b]Range/Switch Code *2 Picture Size (P&P) PAP Input Detect *2 (Left) 0x36 PAP Input Detect *2 (Right) 0x45 0x46 Control Mode On Off Timer Mode*2 FWD-40LX2F/40LX2X/32LX2F/32LX2X KLH-W32/W26 0x00 Large Left 0x01 Even 0x02 Large Right 0x08 INPUT1 RGB (Analog) 0x09 INPUT1 YUV (Analog) 0x0C OPTION1 VIDEO 0x0D OPTION1 S-VIDEO 0x0E OPTION1 RGB 0x0F OPTION1 COMPONENT 0x10 OPTION2 VIDEO 0x11 OPTION2 S-VIDEO 0x12 OPTION2 RGB 0x13 OPTION2 C
Code Table (1-a) [a]Function 0x47 0x48 0x65 On Timer Enable [b]Range/Switch Code *2 Off Timer Enable*2 IP Setting Mode Command Control Enquiry Standby Power On Yes Yes Enable Enable Yes Yes Enable Enable Yes Yes Enable Enable No Yes Enable Enable Yes No Enable Enable Yes Yes Enable Enable Yes Yes Disable Enable bit0 Sunday 1:Enable, 0:Disable bit1 Monday 1:Enable, 0:Disable bit2 Tuesday 1:Enable, 0:Disable bit3 Wednesday 1:Enable, 0:Disable bit4 Thursday 1:Ena
Code Table (1-a) [a]Function 0x71 Default Input 0x73 Auto Signal Detect 0x74 0x75 0x76 HDMI Signal Detect [b]Range/Switch Code *5 Signal Status *6 VIDEO Signal Detect 0x00 Last Memory 0x01 Option1 0x00 Off 0x01 On 0x00 VIDEO 0x01 PC 0x00 Stable 0x01 Unstable/No Signal 0x00 NTSC 0x01 PAL/SECAM Command Control Enquiry Standby Power On Yes Yes Enable Enable Yes Yes Enable Enable No Yes Disable Enable No Yes Disable Enable No Yes Disable Enable *1: Transmi
(b) Time Control Clock Set (Hour, Minute) Syntax Header Category Function Data1 Data2 Data3 Check Sum Control 0x22 0x03 Hour: 0x00-0x17 Minute: 0x00-0x3B 0xXX 0x8C 0x00 Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x00 0x22 0xFF 0xFF 0xA3 Answer Header Answer Check Sum Control 0x70 0x00 0x70 Completed 0x70 0x01 0x71 Limit Over 0x70 0x02 0x72 Limit Under 0x70 0x03 0x73 Command Canceled Answer Header Answer Return to Data Size Return Dat
Code Table (1-e) Week Select 0x00 Sunday 0x01 Monday 0x02 Tuesday 0x03 Wednesday 0x04 Thursday 0x05 Friday 0x06 Saturday On Timer, Off Timer*1 Syntax Header Category Function Data1 Data2 Data3 Check Sum Control 0x8C 0x00 Code Table (1-f)[a] 0x03 Hour: 0x00-0x17 Minute: 0x00-0x3B 0xXX Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x00 Code Table (1-f)[a] 0xFF 0xFF 0xXX Answer Header Answer Check Sum Control 0x70 0x00 0x70 Completed 0x7
Code Table(1-f) [a]Function [b]Range/Switch code Command Control Enquiry Standby Power On Yes Yes Disable Enable Yes Yes Disable Enable Yes Yes Disable Enable Clock Set 0x22 Hour, Minute 0x23 Week On Timer 0x50 Sunday 0x51 Monday 0x52 Tuesday 0x53 Wednesday 0x54 Thursday 0x55 Friday 0x56 Saturday 0x57 Every day Off Timer 0x58 Sunday 0x59 Monday 0x5A Tuesday 0x5B Wednesday 0x5C Thursday 0x5D Friday 0x5E Saturday 0x5F Every day *1: KLH-W26/W32 does not hav
DNS Primary Syntax Header Category Function Data1 Data2 Data3 Data4 Data5 Check Sum Control 0x8C 0x00 0x63 0x05 Address 0 0x00-0xFF Address 1 0x00-0xFF Address 2 0x00-0xFF Address 3 0x00-0xFF 0xXX DNS Secondary Syntax Header Category Function Data1 Data2 Data3 Data4 Data5 Check Sum Control 0x8C 0x00 0x64 0x05 Address 0 0x00-0xFF Address 1 0x00-0xFF Address 2 0x00-0xFF Address 3 0x00-0xFF 0xXX Answer Header Answer Check Sum Control 0x70 0x00 0x70 Completed 0x7
Code Table (2-a) [a]Function [b]Range/Switch code Command Control Enquiry Standby Power On 0x00 Contrast 0x00-0x64 Yes Yes Disable Enable 0x01 Brightness 0x00-0x64 Yes Yes Disable Enable 0x02 Chroma 0x00-0x64 Yes Yes Disable Enable 0x03 Phase 0x00-0x64 Yes Yes Disable Enable 0x04 Color Temp 0x00 Cool Yes Yes Disable Enable 0x01 Neutral 0x02 Warm 0x00 Standard Yes Yes Disable Enable 0x01 Vivid 0x02 Custom 0x05 TC Control 0x10 Picture Mode 0x30 Volu
Answer Header Answer Check Sum Control 0x70 0x00 0x70 Completed 0x70 0x03 0x73 Command Canceled Answer Header Answer Return to Data Size Return Data1 Return Data2 Check Sum Enquiry 0x70 0x00 0x03 Code Table (2-c) Code Table (2-b)[b] 0xXX Completed Code Table (2-b) [a]Function [b]Range/Switch code 0x05 Red Gain 0x00-0xFF 0x06 Green Gain 0x00-0xFF 0x07 Blue Gain 0x00-0xFF Command Control Enquiry Standby Power On Yes Yes Disable Enable Code Table (2-c) Format Sele
Code Table (3-b) [a]Function 0x01 [b]Range/Switch code H Shift *2 Command Control Enquiry Standby Power On (PC) 0x00-0x3C, (Video) 0x00-0x0A Yes Yes Disable Enable (Video) 0x00-0x0A Yes Yes Disable Enable 0x02 V Size 0x03 V Shift (PC) 0x00-0x28, (Video) 0x00-0x0A Yes Yes Disable Enable 0x04 Aspect 0x00 Wide Zoom (VIDEO Only) Yes Yes Disable Enable 0x01 Zoom (VIDEO Only) 0x02 Full (VIDEO Only) 0x04 Normal (PC, VIDEO) 0x05 Full 1 (PC Only) 0x06 Full 2 (PC Only) 0x00
[a]Function 0x0D 0x0F [b]Range/Switch code Multi Position (x4)*1*3 Multi Display Output *3 0x10 0x00 Position1 0x01 Position2 0x02 Position3 0x03 Position4 0x04 Position5 0x05 Position6 0x06 Position7 0x07 Position8 0x08 Position9 0x09 Position10 0x0A Position11 0x0B Position12 0x0C Position13 0x0D Position14 0x0E Position15 0x0F Position16 0x00 Tiles Format 0x01 Window Display Area*3 0x00 Normal 0x01 _1 0x02 _2 Command Control Enquiry Standby Power On Y
7.
(d) Soft Version (Main CPU) Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x30 0x03 0xFF 0xFF 0xB4 Answer Header Answer Return to Data Size Return Data1 Return Data2 Check Sum Enquiry 0x70 0x00 0x03 Upper 8bit Data Lower 8bit Data 0xXX Completed Return Data1-Data2: 0x0000-0x9999 (BCD Format) ex) In Version0.100, it is set to 01 and 00.
(g) Auto Input Detect Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x30 0x30 0xFF 0xFF 0xE1 Answer Header Answer Return to Data Size Return Data1 Return Data2 Return Data3 Return Data4 Return Data5 Enquiry 0x00 0x0C Input1 Input Type Code Table (4-e) Input2 Input Type Code Table (4-e) Input3 Input Type Code Table (4-e) Input4 Input Type Code Table (4-e) Input5 Input Type Code Table (4-e) 0x70 Return Data6 Return Data7 Return Data8 Return Data9 Return
KLH-W26/W32 Input Input Type (Basic) INPUT1 0x06 RGB/YUV (Analog) INPUT2 0x08 HDMI INPUT3 0x08 HDMI INPUT4 0x00 No Input INPUT5 0x00 No Input OPTION1 Option Type Input Type (Option) 0x00 Analog Only 0x00 No Input 0x00 Analog Only 0x03 Video/S-Video 0x00 Analog Only 0x06 RGB/YUV (Analog) 0x00 Analog Only 0x07 Video/S-Video/RGB/YUV (Analog) 0x03 Com Only 0x00 No Input OPTION2 0x00 Analog Only 0x00 No Input OPTION3 0x00 Analog Only 0x00 No Input (h) Auto Panel
8.
Code Table (6) Function Range/Switch code 0x00 Service Mode IN 0x01 Service Mode Exit Command Control Enquiry Normal Mode Service Mode Yes Yes Disable Enable Command Control Enquiry Normal Mode Service Mode Yes Yes Disable Enable Code Table (7) Function Range/Switch code 0x00 User Mode 0x01 Service Mode (b) Factory Reset Syntax Header Category Function Data1 Data2 Check Sum Control 0x8C 0x40 Code Table (8) 0x02 0xFF 0xXX Answer Header Answer Check Sum Control 0
The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation. Le matériel contenu dans ce manuel consiste en informations qui sont la propriété de Sony Corporation.
FWD-40LX2F (WW) FWD-40LX2X (WW) FWD-32LX2F (WW) FWD-32LX2X (WW) KLH-W32 (WW) KLH-W26 (WW) E 9-834-146-01 Sony Corporation Printed in Japan 2006.
