Preparing the camera Before your operation Shooting images Using the shooting function Using the viewing function Changing your setup Viewing images on a computer Printing images Additional information on this product and answers to frequently asked questions can be found at our Customer Support Website. Digital Single Lens Reflex Camera Instruction Manual DSLR-A300/A350 Printed on 70% or more recycled paper using VOC (Volatile Organic Compound)-free vegetable oil based ink.
Owner’s Record The model and serial numbers are located on the bottom. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. DSLR-A300/A350 Serial No. __________________________ WARNING To reduce fire or shock hazard, do not expose the unit to rain or moisture. For Customers in the U.S.A.
IMPORTANT SAFEGUARDS For your protection, please read these safety instructions completely before operating the appliance, and keep this manual for future reference. Attachments Carefully observe all warnings, precautions and instructions on the appliance, or the one described in the operating instructions and adhere to them. Cleaning Use Power Sources This set should be operated only from the type of power source indicated on the marking label.
– Never block the slots and openings by placing the set on a bed, sofa, rug, or other similar surface. – Never place the set in a confined space, such as a bookcase, or built-in cabinet, unless proper ventilation is provided. – Do not place the set near or over a radiator or heat register, or where it is exposed to direct sunlight.
Read this first CAUTION Replace the battery with the specified type only. Otherwise, fire or injury may result. Do not expose the batteries to excessive heat such as sunshine, fire or the like. For Customers in the U.S.A. and Canada RECYCLING LITHIUM-ION BATTERIES Lithium-Ion batteries are recyclable. You can help preserve our environment by returning your used rechargeable batteries to the collection and recycling location nearest you.
CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Disposal of waste batteries (applicable in the European Union and other European countries with separate collection systems) This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste. By ensuring these batteries are disposed of correctly, you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of the battery.
Notes on using your camera Shooting procedure • This camera has two modes for shooting: the Live view mode using the LCD monitor, and the viewfinder mode using the viewfinder (OVF). • There may be differences between an image recorded in Live view mode and an image recorded in viewfinder mode, such as exposure, white balance, or Drange optimizer, depending on the method used of metering or the exposure mode.
Table of Contents IMPORTANT SAFEGUARDS ........................................ 3 Read this first ..................................................................... 5 Notes on using your camera .............................................. 8 Preparing the camera Checking the accessories supplied .................................. 13 Preparing the battery pack ............................................... 14 Attaching a lens ...............................................................
Shooting an image the way you want it (Exposure mode) ..................................................................................... 56 Shooting with program auto .................................. 57 Shooting by controlling the blur of the background (Aperture priority) ............................................. 59 Shooting a moving subject with various expressions (Shutter speed priority) ..................................... 61 Shooting with the exposure adjusted manually (Manual exposure) ....
Selecting the method for measuring the brightness of a subject (Metering mode) ................................... 89 Setting ISO ...................................................................... 90 Adjusting the color tones (White balance) ...................... 91 Adjusting the white balance to suit a specific light source (Auto/Preset white balance) .............................. 91 Setting the color temperature and a filter effect (Color Temperature/Color filter) ..................................
Viewing images on a computer Copying images to your computer ................................ 127 Viewing images on your computer ................................ 131 Using the software ......................................................... 135 Printing images Specifying DPOF ........................................................... 141 Printing images by connecting the camera to a PictBridge compliant printer ...................................................... 143 Others Specifications .......
Preparing the camera Checking the accessories supplied The number in parentheses indicates the number of pieces.
Preparing the battery pack When using the camera for the first time, be sure to charge the NPFM500H “InfoLITHIUM” battery pack (supplied). Charging the battery pack The “InfoLITHIUM” battery pack can be charged even when it has not been fully depleted. It can also be used when it has not been fully charged. 1 Insert the battery pack on the battery charger. Push the battery pack until it clicks. 2 Connect the power cord (mains lead).
• We recommend charging the battery pack in an ambient temperature of between 10 to 30°C (50 to 86°F). You may not be able to efficiently charge the battery pack outside of this temperature range. Preparing the camera Notes • Connect the battery charger to an easily accessible wall outlet (wall socket) close by. • Even if the CHARGE lamp is not lit, the battery charger is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet (wall socket).
Inserting the charged battery pack 1 While sliding the battery cover open lever, open the battery cover. 2 Firmly insert the battery pack all the way while pressing the lock lever with the tip of the battery. Lock lever 3 Close the battery cover. To remove the battery pack Turn off the camera and slide the lock lever in the direction of the arrow. Be careful not to drop the battery pack.
To remove the battery cover Preparing the camera The battery cover can be removed to attach a vertical grip (not supplied). To remove the cover, push the lever in the direction of the arrow and slide it out. To attach the cover, put the knob in the hole, pull down the lever, and slide it in. To check the remaining battery level Set the POWER switch to ON and check the level on the LCD monitor. The level is indicated with the percent figures, in addition to the following indicators.
Effective use of the battery pack • Battery performance decreases in low temperature surroundings. So, the time that the battery pack can be used is shorter in cold places. We recommend the following to ensure longer battery pack use: put the battery pack in a pocket close to your body to warm it up, and insert it in your camera immediately before you start shooting. • The battery pack will run out quickly if you use the flash frequently. Battery life • The battery life is limited.
Attaching a lens 1 Remove the body cap from the Body cap Rear cap 2 Mount the lens by aligning the orange index marks on the lens and camera. Preparing the camera camera and the rear cap from the lens. Orange index marks 3 Turn the lens clockwise until it clicks into the locked position. Notes • When attaching a lens, do not press the lens release button. • Do not use force when attaching a lens. Lens hood Using a lens hood is recommended to prevent unnecessary light from affecting your images.
To remove the lens 1 Press the lens release button all the way in and turn the lens counterclockwise until it stops. • When changing the lens, quickly change the lens away from dusty locations so as to keep dust from getting inside the camera. Lens release button 2 Replace the cap on the lens and attach the body cap to the camera. • Before you attach the cap, remove dust from the cap.
Inserting a memory card You can use a CompactFlash card (CF card), Microdrive, or “Memory Stick Duo” as a memory card. Preparing the camera 1 Open the memory card cover. 2 Insert a memory card (not supplied) from the terminal side (the terminal side has a number of small holes) with its label side facing toward the LCD monitor.
To remove the memory card Check that the access lamp is not lit, then open the memory card cover, push down the memory card eject lever. After the card is ejected a little, pull out the memory card. Access lamp Memory card eject lever Notes on using memory cards • The memory card may be hot just after it has been used for a long time. Be careful when you handle it. • When the access lamp is lit, do not remove the memory card or the battery pack, or turn off the power. The data may be corrupted.
On the “Memory Stick” • “Memory Stick”: You cannot use the “Memory Stick” with your camera. Preparing the camera • The Microdrive is a compact hard disk drive. Since the Microdrive is a rotating disk, the Microdrive is not strong enough to resist vibration and shock compared to a memory card. Be sure not to transmit vibration or shock to the Microdrive during playback or shooting. • Note that the use of the Microdrive under 5°C (41°F) may bring performance degradation.
• Do not use or store the “Memory Stick Duo” under the following conditions: – High temperature locations such as the hot interior of a car parked in direct sunlight. – Locations exposed to direct sunlight. – Humid locations or locations with corrosive substances present.
Preparing the camera Setting up the date 1 Set the POWER switch to ON to turn the camera on. • To turn the camera off, set it to OFF. Preparing the camera When you turn the camera on for the first time, the date/time setup screen appears. 2 Verify that [OK] is selected on the LCD monitor, then press the center of the controller. 3 Select each item with b/B and set the numeric value with v/V.
4 Repeat step 3 to set other items, then press the center of the controller. • When changing the sequence of [YYYY/MM/DD], first select [YYYY/ MM/DD] with b/B, then change it with v/V. 5 Verify that [OK] is selected, then press the center of the controller. To cancel the date/time setting operation Press the MENU button.
Using the accessories supplied Attaching the shoulder strap Attach the both ends of the strap on the camera. Preparing the camera This section describes how to use the shoulder strap and the eyepiece cover. The other accessories are described in the following pages.
1 Tilt the LCD monitor downward. 2 Carefully slide the eyecup off by pushing on each side of the eyecup. • Insert your fingers under the eyecup, and slide it upward. 3 Slide the eyepiece cover over the viewfinder. Note • The eyepiece sensors located below the viewfinder may be activated depending on the situation, and the focus may be adjusted or the LCD monitor may continue to flash. In such cases, set [Eye-Start AF] (page 67) and [Auto off w/ VF] (page 123) to [Off].
Checking the number of recordable images Notes • If “0” is flashing in yellow, the memory card is full. Replace the memory card with another one, or delete images in the current memory card (pages 21, 110). • When “----” (the number of recordable images) flashes in yellow, it means no memory card is inserted. Insert a memory card.
DSLR-A300 Capacity 1GB 2GB 4GB 8GB 325 653 1307 2606 Fine 241 484 969 1933 RAW & JPEG 48 98 198 397 RAW 61 124 250 500 Size Standard * When [Aspect ratio] is set to [16:9], you can record more images than the numbers shown in the table above. However, if it is set to [RAW], the number is the same as that of the [3:2] aspect ratio.
Cleaning Cleaning the LCD monitor Cleaning the lens • When cleaning the lens surface, remove dust using a blower. In case of dust that sticks to the surface, wipe it off with a soft cloth or tissue paper slightly moistened with lens cleaning solution. Wipe in a spiral pattern from the center to the outside. Do not spray lens cleaning solution directly onto the lens surface. • Do not touch the inside of the camera, such as lens contacts, or the mirror.
Cleaning the image sensor If dust or debris enters the camera and lands on the image sensor (the part that acts as the film), it may appear on the photo image, depending on the shooting environment. If there is dust on the image sensor, use a commercially available blower and clean the image sensor following the steps below. You can easily clean the image sensor using only the blower and the anti-dust function.
5 Detach the lens (page 20). 6 Use the blower to clean the image • Do not touch the image sensor with the tip of the blower. Complete the cleaning quickly. • Hold the camera’s face downward to prevent the dust from resettling in the camera. • When cleaning the image sensor, do not put the tip of a blower into the cavity beyond the lens mount. Preparing the camera sensor surface and the surrounding area. 7 Attach the lens and set the POWER switch to OFF.
Before your operation Identifying parts and screen indicators See the pages in parentheses for details of operation. Front side A Shutter button (48) B Control dial (58, 120) C Self-timer lamp (98) D Lens contacts* E Mirror* F Lens mount G Built-in flash* (79) H Mode dial (48) I (Flash pop-up) button (79) J Lens release button (20) K Focus mode switch (72, 75) * Do not directly touch these parts.
Rear side Before your operation A Accessory shoe (71) • You can adjust the angle of the LCD monitor to meet various shooting situations.
Q (Smart teleconverter) button (77) R For shooting: Fn (Function) button (40) For viewing: (Image rotation) button (102) S Access lamp (22) T Controller (Enter)/Spot AF button (75) U Controller (v/V/b/B) V (Super SteadyShot) switch (46) 36
Sides/Bottom (112, 128) B Memory card cover C Memory card insertion slot (21) D Memory card eject lever (22) E Hooks for shoulder strap (27) F REMOTE terminal H Battery cover (17) I Tripod receptacle • Use a tripod with a screw length of less than 5.5 mm (7/32 inch). You will be unable to firmly secure the camera to tripods having screws longer than 5.5 mm (7/32 inch), and may damage the camera.
LCD monitor The indicators on the monitor are displayed as follows in Live view mode. For the indicators in viewfinder mode, see page 71.
Display Indication D Camera shake warning (45) Display Indication Focus mode (74) Super SteadyShot scale (46) AF area (75) Metering (89) ISO ISO sensitivity (90) Before your operation To switch the recording information display Each time you press the DISP button, the screen changes as follows.
Selecting a function/setting You can select a function for shooting or playback from the menu list. To display the menu list, press the Fn (Function) button, (Drive) button, or MENU button. Example: When the Fn button is pressed. From the menu list, use the controller to move the cursor to the setting of your choice and execute the selection. : Press v/V/b/B on the controller to move the cursor. z: Press the center button to execute the selection.
2 Following the operation guide, select [White balance] with v/V/ b/B on the controller, then press the center z to execute. Operation guide select and execute the desired function. For example, to change [5500K] (the current setting), select [5500K] with v/ V, adjust the value of [ColorTemperature] with b/B, then press the center z to execute.
The functions selected by the Fn (Function) button Flash mode (page 81) Autofocus mode (page 74) White balance (page 91) Metering mode (page 89) AF area (page 75) D-RangeOptimizer (page 95) The functions selected by the (Drive) button Single-shot adv. (page 97) Continuous adv. (page 97) Self-timer (page 98) Bracket: Cont.
Playback menu Delete (110) Format (117) Protect (109) 1 DPOF setup (141) • Date imprint (142) • Index print (142) 2 PlaybackDisplay (101) Slide show (105) • Interval (105) Setup menu Pixel mapping (154) 3 Cleaning mode (32) Reset default (125) File number (116) Folder name (116) Select folder (117) 2 • New folder (117) USB connection (128, 143) Audio signals (121) Before your operation LCD brightness (122) Info.disp.
Shooting images Shooting an image without camera shake “Camera shake” refers to an unwanted movement of the camera that occurs after the shutter button has been pressed, resulting in a blurred image. To reduce camera shake, follow the instructions below. Correct posture When using the LCD monitor Low position High position When using the viewfinder Stabilize your upper body and take a position that keeps the camera from moving.
Point 1 One hand holds the grip of the camera, and the other hand supports the lens. Point 2 Take a secure stance with your feet shoulder-width apart. Point 3 Lightly tuck your elbows against your body. When shooting in a kneeling position, steady your upper body by placing your elbow on your knee. Camera shake warning indicator Due to potential camera shake, the (Camera shake warning) indicator flashes. In this case, use the Super SteadyShot function, a tripod, or the flash.
Using the Super SteadyShot function This Super SteadyShot function can reduce the effect of camera shake by the equivalent of approximately 2.5 to 3.5 increments of shutter speed. Set the switch to “ON.” • The (Super SteadyShot scale) indicator appears. Wait until the scale becomes low, then start shooting.
Using a tripod In the following cases, we recommend that you mount the camera on a tripod. • Shooting without a flash under dark conditions. • Shooting with slow shutter speeds, which are typically used in night-time shooting. • Shooting a close subject, such as in macro shooting. • Shooting with a telescopic lens. • Shooting a moving subject. Shooting images Note • When using a tripod, deactivate the Super SteadyShot function.
/ Shooting with the automatic setting The “AUTO” mode allows you to easily shoot any subject under any conditions. Select when shooting in a location where the use of a flash is restricted. 1 Set the mode dial to or (Flash Off). or 2 Hold the camera and look into the viewfinder. Focus area 3 Place the desired subject within the focus area. • If the (Camera shake warning) indicator flashes, set the switch to ON to activate the Super SteadyShot function, or use a tripod.
5 Press the shutter button halfway down to focus. When the focus is confirmed, the focus indicator z or (Focus indicator) lights up (page 72). 6 Press the shutter button fully Shooting images Focus indicator down to shoot. • When the switch is set to ON, wait until the scale of the (Super SteadyShot scale) indicator becomes low, then start shooting.
Shooting with a suitable setting for the subject (Scene Selection) Selecting an appropriate mode for the subject or the shooting conditions allows you to shoot the image with a more suitable setting for the subject than in “AUTO” mode. Taking portrait photos This mode is suitable to z Blur away backgrounds and sharpen the subject. z Reproduce skin tones softly. Set the mode dial to (Portrait). Shooting techniques • To blur the background more, set the lens to the telephoto position.
Taking landscape photos This mode is suitable to z Shoot the entire range of scenery in sharp focus with vivid colors. (Landscape). Shooting technique Shooting images Set the mode dial to • To accentuate the openness of the scenery, set the lens to wide angle.
Taking small-subject photos This mode is suitable to z Shoot close subjects such as flowers, insects, dishes, or small goods. You can achieve clear and sharp focus. Set the mode dial to (Macro). Shooting techniques • Get close to the subject and shoot at the minimum distance of the lens. • You can shoot a closer subject using a macro lens. • Set the built-in flash to (Flash Off) when you shoot a subject within 1 m (3.3 feet).
Taking moving-subject photos This mode is suitable to z Shoot moving subjects outdoors or in bright places. (Sports action). Shooting techniques Shooting images Set the mode dial to • The camera shoots images continuously while the shutter button is pressed. • Press and hold the shutter button halfway down until the right moment. • Set the ISO sensitivity higher when shooting in poor light (page 90).
Taking sunset photos This mode is suitable to z Shoot the red of the sunset beautifully. Set the mode dial to (Sunset). Shooting techniques • Used to shoot an image accentuating the red color compared with other modes. This is also suitable for shooting the beautiful red of the sunrise. • You can adjust the depth of the color by exposure compensation. Shifting to the under side (–) deepens the colors, while shifting to the over side (+) attenuates the colors.
Taking night view photos This mode is suitable to z Shoot portraits in night scenes. without losing the dark atmosphere of the surroundings. Set the mode dial to Set [Flash mode] to persons (page 81). Shooting images z Shoot night scenes at a distance (Night portrait/Night view). (Flash Off) when you shoot a night view without Shooting techniques • Take care that the subject does not move to prevent the image from blurring. • The shutter speed is slower, so using a tripod is recommended.
Shooting an image the way you want it (Exposure mode) With a single lens reflex camera, you can adjust the shutter speed (how long the shutter is open) and aperture (the range that is in focus: depth of field) to enjoy a variety of photographic expressions. For example, you can use a fast shutter speed to shoot the ephemeral shape of a wave, or you can accentuate a flower by opening the aperture to put everything in front of and beyond the flower out of focus.
Shooting with program auto This mode is suitable to z Use the automatic exposure, while keeping the custom settings for ISO sensitivity, Creative Style, D-Range optimizer, etc. measured by the camera, but change the combination of shutter speed and aperture depending on the subject (Program shift). Shooting images z Keep the exposure compensation 1 Set the mode dial to P. 2 Set the shooting functions to your desired settings (pages 72 to 100). The settings will be stored until you reset the settings.
To use Program shift 1 Press the shutter button halfway down to adjust the focus. The correct exposure (shutter speed and aperture value) determined by the camera is indicated. Aperture value Shutter speed 2 Rotate the control dial to select your desired combination while the focus is achieved. The recording mode indicator is switched to “PS” (Shutter speed priority program shift), and the shutter speed and aperture value are changed.
Shooting by controlling the blur of the background (Aperture priority) This mode is suitable to z Put the subject in sharp focus and blur everything in front of and beyond the subject. Opening the aperture narrows the range that is in focus. (Depth of field becomes shallower.) Narrowing down the aperture widens the range that is in focus. (Depth of field becomes deeper.) Shooting images z Shoot the depth of the scenery. 1 Set the mode dial to A.
2 Select the aperture value (Fnumber) with the control dial. • Smaller F-number: The foreground and background of the subject are blurred. Larger F-number: The subject and its foreground and background are also focused on. • You cannot check the blurring of an image in the viewfinder. Check the recorded image and adjust the aperture. Aperture (F-number) 3 Adjust the focus and shoot the subject. The shutter speed is automatically adjusted to obtain correct exposure.
Shooting a moving subject with various expressions (Shutter speed priority) This mode is suitable to z Shoot a moving subject at a moment in time. Use a faster shutter speed to crisply shoot an instant of the movement. dynamism and flow. Use a slower shutter speed to shoot a trailing image of the moving subject. Shooting images z Trace the movement to express the 1 Set the mode dial to S.
2 Select the shutter speed with the control dial. Shutter speed 3 Adjust the focus and shoot the subject. The aperture is automatically adjusted to obtain correct exposure. • When the camera judges that the proper exposure is not obtained with the selected shutter speed, the aperture value flashes. In such cases, adjust the shutter speed again. Aperture (F-number) Shooting techniques • When the shutter speed is slower, use a tripod. • When shooting an indoor sport, select a higher ISO sensitivity.
Shooting with the exposure adjusted manually (Manual exposure) This mode is suitable to z Shoot with the desired exposure setting by adjusting both the shutter speed and aperture. z Use an exposure meter. Shooting images 1 Set the mode dial to M. 2 Rotate the control dial to adjust the shutter speed, and while pressing the button, rotate the control dial to adjust the aperture. • You can assign a function to the control dial with [Ctrl dial setup] (page 120).
3 Shoot the image after the exposure is set. • Check the exposure value on the EV scale. Toward +: Images become brighter. Toward –: Images become darker. The b B arrow appears if the set exposure is beyond the range of the EV scale. The arrow starts flashing if the difference becomes greater. Standard value Notes • The (Camera shake warning) indicator is not indicated in manual exposure mode. • When the mode dial is set to M, the ISO setting [AUTO] is set to [100].
Shooting trails with long exposure (BULB) This mode is suitable to z Shoot trails of light, such as fireworks. z Shoot trails of stars. Shooting images 1 Set the mode dial to M. 2 Rotate the control dial to the left until [BULB] is indicated. BULB 3 While pressing the button, rotate the control dial to adjust the aperture (F-number).
4 Press the shutter button halfway down to adjust the focus. 5 Press and hold the shutter button for the duration of the shooting. As long as the shutter button is pressed, the shutter remains open. Shooting techniques • Use a tripod. • Set the focus to infinity in manual focus mode when shooting fireworks, etc. • If you use a Remote Commander that is equipped with a shutter button lock function (not supplied), you can leave the shutter open using the Remote Commander.
Shooting with the viewfinder (OVF) You can select either the LCD monitor (Live view) or the viewfinder (OVF) to shoot images. Switching to the viewfinder Set the LIVE VIEW/OVF switch to “OVF.” The screen status changes as follows: Shooting images Viewfinder display LCD monitor display When you look into the viewfinder, the subject inside the focus area comes into focus automatically (Eye-Start AF).
Adjusting the focus of the finder (diopter adjustment) Adjust the diopter-adjustment dial to your eyesight until the indicators appear clearly in the viewfinder. • Turn the dial toward + when you are farsighted, toward – when you are near-sighted. • Training the camera on the light allows you to adjust the diopter easily. When it is hard to rotate the diopter-adjustment dial Insert your fingers under the eyecup, and slide it upward.
LCD monitor (Recording information display) A C Display Indication Display P A S M Mode dial (48) 1/125 Shutter speed (61) F5.6 Aperture (59) +2.0 Exposure (63) Drive mode (97) Focus mode (74) AE lock (83) AF area (75) Metering (89) B Display Indication Shooting images • The illustration above is for the detailed display. The enlarged display is displayed as the default setting.
D Display Display 90% Battery remaining (17) Image quality (115) Indication Image size (114)/Aspect ratio (115) Indication 100 Remaining number of recordable images (29) Switching the recording information display Press the DISP button to switch between the enlarged display and the detailed display. When you rotate the camera to a vertical position, the display automatically rotates to adjust to the camera position.
Viewfinder Display Display Indication AF area (75) Spot AF area (75) Spot metering area (89) Shooting area for aspect ratio 16:9 (115) B Display Indication Indication Super SteadyShot scale (46) Aspect ratio 16:9 (115) * When using the HVL-F56AM/HVLF36AM Flash (not supplied), you can shoot with a High-speed sync feature at any shutter speed. For details, refer to the operating instructions supplied with the flash.
Using the shooting function Selecting the focus method There are two methods for adjusting the focus: autofocus and manual focus. Using autofocus 1 Set the focus mode switch to AF. 2 Press the shutter button halfway Focus area sensor down to check the focus and shoot the image. • When the focus is confirmed, the focus indicator changes to z or (page 72). • The green frames are indicated at an area where the focus has been confirmed.
Subjects that may require special focusing: Using the autofocus, it is hard to focus on the following subjects. In such cases, use the focus lock shooting feature (page 73) or manual focus (page 75). • A subject that is low in contrast, such as blue sky or a white wall. • Two subjects at different distances overlapping in the AF area. • A subject that is composed of repeating patterns, such as the facade of a building.
2 Keep the shutter button halfway down, and put the subject back in the original position to recompose the shot. 3 Press the shutter button fully down to take the picture. Selecting the focus method to suit the movement of the subject (Autofocus mode) Fn button t [Autofocus mode] t Select the desired setting (Single-shot AF) The camera focuses on and the focus is locked when you press the shutter button halfway down.
Selecting the focus area (AF area) Select the desired AF are to suit the shooting conditions or your preference. The green frames are indicated at an area where the focus has been confirmed. • The area used for focusing is illuminated briefly in viewfinder mode. AF area Area Fn button t [AF area] t Select the desired setting The camera determines which of the nine AF areas is used in focusing within the AF area.
1 Set the focus mode switch to MF. 2 Rotate the focusing ring of the lens to achieve a sharp focus. Focusing ring Notes • In the case of a subject that can be focused in autofocus mode, the z indicator lights up when the focus is confirmed. When the Wide AF area is used, the center area is used, and when the Local AF area is used, the area that is selected with the controller is used. • The camera resets the focal length to (infinity) when the POWER switch is set to ON. • When using a tele converter, etc.
Zooming in in one step You can zoom in to the center of an image using the smart teleconverter (Digital zoom) and record the image. 1 Set the LIVE VIEW/OVF switch to “LIVE VIEW.” 2 Press the button. button The image size is automatically set to the following: Zoom scaling Image size Approx. ×1.4 M* Approx. ×2 S* Using the shooting function • Each time you press the button, the zoom scaling changes as follows: Off t Approx. ×1.4 t Approx. ×2.
• When [Quality] is set to teleconverter is unavailable.
Using the flash In a dark location, using the flash allows you to shoot the subject brightly, and it also helps to prevent camera shake. When shooting into the sun, you can use the flash to shoot a bright image of the backlit subject. 1 Press the button. button The flash pops up. • In AUTO or Scene Selection mode, the flash automatically pops up if the amount of light is insufficient or the subject is backlit. The built-in flash does not pop up even if you press the button.
• Shooting conditions required to prevent shade from appearing on an image vary, depending on the lens. The flash range The built-in flash range depends on the ISO sensitivity and aperture value. Refer to the following table. Aperture F2.8 F4.0 ISO AUTO 1.4 – 8.6 m (4.6 – 28 1 – 6 m (3.3 – 20 setting feet) feet) F5.6 1 – 4.3 m (3.3 – 14 feet) 100 1 – 4.3 m (3.3 – 14 feet) 1 – 3 m (3.3 – 9.8 feet) 1 – 2.1 m (3.3 – 6.9 feet) 200 1 – 6 m (3.3 – 20 feet) 1 – 4.3 m (3.3 – 14 feet) 1 – 3 m (3.3 – 9.
Selecting the flash mode Fn button t [Flash mode] t Select the desired setting (Flash Off) Does not fire even if the built-in flash pops up. This is not selectable when the mode dial is set to P, A, S, or M. (Autoflash) Fires if it is dark or against light. This is not selectable when the mode dial is set to P, A, S, or M. (Fill-flash) Fires whenever the built-in flash pops up. (Slow sync.) Fires whenever the built-in flash pops up.
Notes • Turn off the wireless flash mode after wireless flash shooting. If the built-in flash is used while the wireless flash mode is still active, inaccurate flash exposures will result. • Change the channel of the external flash when another photographer is using a wireless flash nearby and his/her built-in flash light triggers firing of your flash. To change the channel of the external flash, refer to the operating instructions supplied with it.
Adjusting the brightness of the image (Exposure, Flash compensation, Metering) Shooting with fixed brightness (AE Lock) The spot where you lock the exposure. 1 Fn button t [Metering mode] t Using the shooting function When shooting into the sun or by a window, the exposure may not be appropriate for the subject because of the big difference in lighting between the subject and the background. In such cases, use the light meter where the subject is bright enough and lock the exposure before shooting.
3 Press the AEL button to lock the exposure. (AE lock mark) appears. AEL button 4 While pressing the AEL button, focus on the subject, and shoot the subject. • If you continue to shoot with the same exposure value, press and hold the AEL button after the shooting. The setting is canceled when the button is released. To check the exposure of the image Hold down the AEL button and place the spot metering circle on the spot where the lighting is contrasted from the subject.
Using brightness compensation for the entire image (Exposure compensation) Except for recording mode M, the exposure is automatically acquired. (Automatic exposure) Based on the exposure acquired by the automatic exposure, you can perform exposure compensation by shifting the exposure to either the + side or the – side, depending on your preference. You can make the entire image brighter by shifting to the + side. The entire image becomes darker when you shift it to the – side.
Shooting techniques • Adjust the compensation level by checking the recorded image. • Using bracket shooting, you can shoot multiple images with the exposure shifted to the plus or minus sides (page 98).
To shoot while checking the screen using the histogram Number of pixels A histogram is the luminance distribution that shows how many pixels of a particular brightness exist in the picture. Dark Light Using the shooting function The exposure compensation will change the histogram accordingly. The right illustration is an example. Shooting with the exposure compensation on the positive side brightens the whole picture, making the entire histogram shift to the bright side (right side).
Adjusting the amount of flash light (Flash compensation) When shooting with the flash, you can adjust the amount of flash light alone, without changing the exposure compensation. You can only change the exposure of a main subject which is within the flash range. MENU button t desired setting 1 t [Flash compens.] t Select the • Toward +: Makes the flash level higher. Toward –: Makes the flash level lower.
ADI: Advanced Distance Integration TTL: Through the lens • When [ADI flash] is selected, using a lens that is provided with a distance encoder feature can perform more accurate flash compensation by using more accurate distance information.
Setting ISO Sensitivity to light is expressed by the ISO number (recommended exposure index). The larger the number, the higher the sensitivity. 1 Press the ISO button to display ISO button the ISO screen. 2 Select the desired value with v/V on the controller. • The larger the number, the higher the noise level. Notes • When ISO is set to [AUTO], ISO is automatically set as follows.
Adjusting the color tones (White balance) The color tone of the subject changes depending on the characteristics of the light source. The table below shows how the color tone changes based on various light sources, compared with a subject that appears white under the sunlight.
AWB (Auto WB) The camera automatically detects a light source and adjusts the color tones. (Daylight) If you select an option to suit a specific light source, the color tones are adjusted for the light source (preset white balance). (Shade) (Cloudy) (Tungsten) (Fluorescent) (Flash) Shooting techniques • Use the white balance bracket function if you cannot get the desired color in the selected option (page 100).
5500K*1 (ColorTemperature) Sets the white balance by the color temperature. The higher the number, the more reddish the image and the lower the number, the more bluish the image. 00*2 (Color filter) Achieves the effect of CC (Color Compensation) filters for photography. Based on using the set color temperature as the standard, the color can be compensated to G (Green) or M (Magenta). *1 *2 The value is the color temperature value currently selected.
Note • The message “Custom WB error” indicates that the value is beyond the expected range. (When the flash is used on a subject in close proximity or a subject with a bright color is in the frame.) If you register this value, the indicator turns yellow on the recording information display on the LCD monitor. You can shoot at this point, but it is recommended that you set the white balance again to get a more correct white balance value.
Image processing Correcting the brightness of the image (D-Range Optimizer) Fn button t [D-RangeOptimizer] t Select the desired setting (Off) When there is a sharp contrast of light and shadow between the subject and the background, which is common when shooting into the sun, the camera attenuates the contrast across the entire image to produce an image with proper brightness and contrast.
(Night view) The contrast is attenuated for shooting a nightscape that is more faithful to the real view. (Sunset) For shooting the beautiful red of the setting sun. (B/W) For shooting images in black and white monotone. (Adobe RGB) For shooting images in Adobe RGB color space. (Contrast), (Saturation), and Creative Style item. (Sharpness) can be adjusted for each (Contrast) The difference of light and shadow in an image (gradation). Increase the value to get an image with strong contrast.
Selecting the drive mode This camera has five drive modes, such as single-shot advanced, continuous advanced. Use them for your purpose. Shooting single shot This mode is for normal shooting. button t (Single-shot adv.) Shooting continuously The camera records the images continuously at a following speed*. DSLR-A300 Live view mode Maximum 2 images per second Maximum 2 images per second Viewfinder mode Maximum 2.5 images per Maximum 3 images per second second * Our measurement conditions.
Using the self-timer The 10-second self-timer is convenient when the photographer appears in a photo and the 2-second self-timer is convenient to reduce the camera shake. 1 button t • The number after (Self-timer) t Select the desired seconds is the number of seconds that is currently selected. 2 Adjust the focus and shoot the subject. • When the self-timer is activated, audio signals and the self-timer lamp indicate the condition.
1 button t Desired bracket t Desired bracket step 2 Adjust the focus and shoot the subject. The base exposure is set at the first shot in the bracket. * (Bracket: Shoots three images with the exposure shifted by a selected step. Press and hold the shutter button until the recording stops. * (Bracket: Single) Shoots three images with the exposure shifted by a selected step. Press the shutter button shot by shot. Cont.) * _ ._ EV displayed with / is the step currently selected.
• In ambient* bracket shooting, the EV scale appears on the LCD monitor/ in the viewfinder, too, but it does not appear in flash bracket shooting. • When the bracket shooting starts, the indexes that indicate already recorded images start to disappear one by one. • When Single bracket is selected in viewfinder mode, if the shutter button is pressed halfway down and released, “br 1” appears for the ambient light bracket and “Fbr 1” appears for the flash bracket.
Using the viewing function Playing back images The last recorded image is displayed on the LCD monitor. 1 Press the button. button 2 Select an image with b/B on the controller. To return to the shooting mode Press the button again. To switch the recording data display Press the DISP button. Each time you press the DISP button, the screen changes as follows.
Note • When you play back the image on a TV or a computer, the image will be displayed in the portrait position even if [Manual rotate] is selected. Rotating an image 1 Display the image you want to rotate, then press the button. button 2 Press the center of the controller. The image is rotated counter-clockwise. When you want to do another rotation, repeat step 2. • Once you rotate the image, the image is played back in the rotated position, even if you turn off the power.
2 Zoom the image in or out with the or button. • You can select the portion you want to enlarge with v/V/b/B on the controller. • Rotating the control dial switches the image at the same display magnification. When you shoot multiple images with the same composition, you can compare their focus conditions. • Each time you press the center of the controller, the screen changes between the zoomed screen and the full-screen mode.
4 Scale up or down the red frame to specify the portion you want to enlarge with the or button. 5 Press the center of the controller. The portion inside the red frame is enlarged. • Press the center of the controller to return to the previous screen. • To cancel the enlarged playback, press the button. Scaling range The scaling range is as follows. Image size Scaling range DSLR-A350 DSLR-A300 L Approx. ×1.1 – ×14 Approx. ×1.1 – ×12 M Approx. ×1.1 – ×11 Approx. ×1.1 – ×9.1 S Approx. ×1.1 – ×7.
To select a folder 1 Select the folder bar with b/B on the controller, then press the center. Folder bar 2 Select the desired folder with v/V, then press the center. Playing back images automatically (Slide show) MENU button t 2 t [Slide show] Plays back recorded images in order (Slide show). The slide show automatically stops after all the images have been played back. To pause the slide show Press the center of the controller. Pressing again starts the slide show again.
Checking the information of recorded images Each time you press the DISP button, the information display changes (page 101). Basic information display Display Indication 100-0003 Folder - file number (132) - Protect (109) DPOF3 DPOF set (141) Image quality (115) Image size (114)/Aspect ratio (115) Battery remaining warning (17) 106 1/125 Shutter speed (61) F3.
Histogram display A Display Indication 100-0003 Folder - file number (132) - Protect (109) DPOF3 DPOF set (141) Indication 35mm Focal length (149) Creative Style (95) AWB +1 5500K M1 White balance (Auto, Preset, Color temperature, Color filter, Custom) (91) D-Range Optimizer (95) Image size (114)/Aspect ratio (115) Battery remaining warning (17) B Display 2008 1 1 10:37AM Date of recording 3/7 File number/total number of images Using the viewing function Image quality (115) Display Ind
How to check the histogram When the image has a high-key or lowkey portion, that portion is flashed on the histogram display (Luminance limit warning).
Protecting images (Protect) You can protect images against accidental erasure. Protecting selected images/canceling the protection of the selected images 1 MENU button t 1 t [Protect] t [Marked images] 2 Select the image you want to - protect with b/B on the controller, then press the center of the controller. 3 To protect other images, repeat step 2. 4 Press the MENU button. 5 Select [OK] with v on the controller, then press the center of the controller.
Deleting images (Delete) Once you have deleted an image, you cannot restore it. Check whether you delete the image or not beforehand. Note • Protected images cannot be deleted. Deleting the image that is currently displayed 1 Display the image you want to delete and press the button. button 2 Select [Delete] with v, then press the center of the controller.
5 Select [Delete] with v on the controller, then press the center of the controller. Deleting all the images in the folder 1 Press the button. 2 Select the folder bar with b on the controller. Folder bar want to delete with v/V. 4 Press the button. 5 Select [Delete] with v, then press the center of the controller.
Viewing images on a TV screen 1 Turn off both your camera and the TV, and connect the camera to the TV. 1 To video input jack Video cable 2 To the VIDEO OUT terminal 2 Turn on the TV and switch the input. • See also the operating instructions supplied with the TV. 3 Turn on the camera, and press the button. Images shot with the camera appear on the TV screen. Select the desired image with b/B on the controller. • The LCD monitor on the rear of the camera does not turned on.
To use your camera abroad It may be necessary to switch the video signal output to match that of your TV system. MENU button t setting 1 t [Video output] t Select the desired NTSC Sets the video output signal to NTSC mode (e.g., for the USA, Japan). PAL Sets the video output signal to PAL mode (e.g., for Europe). On TV color systems If you want to view images on a TV screen, you need a TV with a video input jack and the video cable.
Changing your setup Setting image size and image quality Image size MENU button t 1 t [Image size] t Select the desired size [Aspect ratio]: [3:2] DSLR-A350 L:14M 4592 × 3056 pixels M:7.7M 3408 × 2272 pixels S:3.5M 2288 × 1520 pixels DSLR-A300 L:10M 3872 × 2592 pixels M:5.6M 2896 × 1936 pixels S:2.5M 1920 × 1280 pixels [Aspect ratio]: [16:9] DSLR-A350 L:12M 4592 × 2576 pixels M:6.5M 3408 × 1920 pixels S:2.9M 2288 × 1280 pixels DSLR-A300 L:8.4M 3872 × 2176 pixels M:4.
Aspect ratio MENU button t ratio 1 t [Aspect ratio] t Select the desired 3:2 A normal ratio. 16:9 An HDTV ratio. Quality MENU button t (RAW) (RAW & JPEG) (Standard) File format: RAW (raw data) This format does not perform any digital processing on the images. Select this format to process images on a computer for professional purposes. • The image size is fixed to the maximum size. The image size is not displayed on the LCD monitor.
Setting the method for recording on a memory card Selecting the method for assigning file numbers to images MENU button t setting 2 t [File number] t Select the desired Series The camera does not reset numbers and assigns numbers to files in sequence until the number reaches “9999.” Reset The camera resets numbers in the following cases and assigns numbers to files from “0001.” – – – – When the folder format is changed. When all the images in the folder are deleted. When the memory card is replaced.
Creating a new folder You can create a folder in a memory card for recording images. A new folder is created with a number incremented one higher than the largest number currently used, and the folder becomes the current recording folder. MENU button t 2 t [New folder] Selecting the recording folder When a standard form folder is selected and there are two or more folders, you can select the recording folder to be used to record images.
Changing the noise reduction setting Disabling the noise reduction at a long exposure shooting When you set the shutter speed to a second or longer (Long exposure shooting), the noise reduction is turned on for the same duration as the shutter was open. This is to reduce the grainy noise typical in a long exposure. When noise reduction is in progress, a message appears and you cannot take another picture. Select [On] to prioritize the image quality. Select [Off] to prioritize the timing of shooting.
Changing the conditions under which the shutter can be released Prioritizing the shutter opportunity To prioritize the shutter opportunity, select [Release] so you can shoot without acquiring a sharp focus. To shoot with a sharp focus, select [AF].
Changing the functions of the button and dial Changing the function of the AEL button The function of the AEL button can be selected from the following two functions: – Holding the locked exposure value by pressing the AEL button while the button is held down ([AEL hold]). – Holding the locked exposure value by pressing the AEL button until the button is pressed again ([AEL toggle]).
Changing other settings Setting the sound on/off Selects the sound produced when the shutter is locked, during self-timer countdown, etc. MENU button t setting 2 t [Audio signals] t Select the desired Setting the time to turn the camera to the power save mode You can set the time to turn the camera to the power saving mode (Power save). Pressing the shutter button halfway down returns the camera to the shooting mode.
Setting the LCD monitor Setting the brightness of the LCD monitor MENU button t setting 1 t [LCD brightness] t Select the desired • On the recording information or playback screen, you can adjust the brightness by pressing the DISP button a little longer. Setting the displayed time of the image right after shooting (Auto review) You can check the recorded image on the LCD monitor right after the shooting. You can change the displayed time.
Keeping on the LCD monitor while looking into the viewfinder When the LIVE VIEW/OVF switch is set to “OVF,” looking into the viewfinder turns off the LCD monitor. In the default setting, while looking into the viewfinder, the LCD monitor is turned off to prevent the battery pack wearing down. If you want to turn on the LCD monitor while looking into the viewfinder, select [Off].
Resetting to the default Resetting the functions used for shooting to the default setting You can reset the main functions of the recording mode when the mode dial is set to P, A, S, or M. MENU button t 2 t [Rec mode reset] t [OK] The items to be reset are as follows. 124 Items Reset to Exposure compensation (85) ±0.0 Metering mode (89) Multi segment Autofocus mode (74) AF-A Drive mode (97) Single-shot adv.
Resetting the main functions of the camera to the default setting You can reset the main functions of the camera. MENU button t 3 t [Reset default] t [OK] The items to be reset are as follows. Items Reset to Exposure compensation (85) ±0.0 Metering mode (89) Multi segment Autofocus mode (74) AF-A Recording information display (69) Enlarged display Drive mode (97) Single-shot adv.
Custom menu Items Reset to Eye-Start AF (67) On AEL button (120) AEL hold Ctrl dial setup (120) Shutter speed Red eye reduc. (80) Off Auto review (122) 2 sec Auto off w/ VF (123) On Playback menu Items Reset to Date imprint (142) Off PlaybackDisplay (101) Auto rotate Slide show (105) 3 sec Setup menu 126 Items Reset to LCD brightness (122) ±0 Info.disp.
Viewing images on a computer Copying images to your computer This section describes how to copy images in a memory card to a computer connected using a USB cable. Recommended computer environment The following environment is recommended for a computer connected to the camera to import images.
Stage 1: Connecting the camera and your computer 1 Insert a memory card with recorded images into the camera. 2 Insert the sufficiently charged battery pack in the camera, or connect the camera to a wall outlet (wall socket) with the AC Adaptor/charger (not supplied). • When you copy images to your computer using insufficient battery pack, copying may fail or image data may become corrupted if the battery pack shuts down too soon. 3 Turn on the camera and the computer.
Stage 2: Copying images to a computer For Windows This section describes an example of copying images to a “My Documents” (For Windows Vista: “Documents”) folder. 1 Click [Copy pictures to a folder on my computer using Microsoft Scanner and Camera Wizard] t [OK] as the wizard screen appears automatically on the desktop. • When the wizard screen does not appear, click [My Computer] t [Removable Disk]. 2 Double-click [DCIM]. • In that case, you can also import images using “Picture Motion Browser.
4 Double-click the [My Documents] (For Windows Vista: [Documents]) folder. Then, rightclick on the “My Documents” window to display the menu and click [Paste]. The image files are copied to the “My Documents” (For Windows Vista: “Documents”) folder. • When an image with the same file name exists in the copy destination folder, the overwrite confirmation message appears. When you overwrite an existing image with a new one, the original file data is deleted.
Viewing images on your computer For Windows This section describes the procedure for viewing copied images in the “My Documents” (For Windows Vista: “Documents”) folder. 1 Click [Start] t [My Documents] (For Windows Vista: [Documents]). • If you are using Windows 2000, double-click [My Documents] on the desktop. 2 Double-click the desired image file. The image is displayed. Double-click the hard disk icon t the desired image file to open the image file.
Deleting the USB connection Perform the procedures listed below beforehand when: • Disconnecting the USB cable. • Removing the memory card. • Turning off the camera. x For Windows Double-click on the tasktray, then click (USB Mass Storage Device) t [Stop]. Confirm the device on the confirmation window, then click [OK] t [OK] (unnecessary for Windows XP/Vista). The device is disconnected. x For Macintosh Drag and drop the drive icon or the icon of the memory card to the “Trash” icon.
Example: viewing folders on Windows XP Copying images stored on a computer to a memory card and viewing the images This section describes the process using a Windows computer as an example. Viewing images on a computer AFolders containing image data recorded using this camera. (The first three digits show the folder number.) BYou can create a folder by date form (page 116). • You cannot record/play back any images in the “MISC” folder. • Image files are named as follows.
1 Right-click the image file, then click [Rename]. Change the file name to “DSC0ssss.” Enter a number from 0001 to 9999 for ssss. • If the overwrite confirmation message appears, enter a different number. • An extension may be displayed depending on the computer settings. The extension for images is JPG. Do not change the extension. • Step 1 is not necessary if the file name set with your camera has not been changed. 2 Copy the image file to the memory card folder in the following order.
Using the software To utilize images recorded with the camera, the following software is provided: “Picture Motion Browser,” “Image Data Converter SR,” “Image Data Lightbox SR” etc. Note • “Picture Motion Browser” is not compatible with Macintosh computers. Recommended computer environment x Windows Recommended environment for using “Picture Motion Browser” OS (pre-installed): Microsoft Windows 2000 Professional SP4/Windows XP* SP2/Windows Vista* * 64-bit editions and Starter (Edition) are not supported.
Display: 1024 × 768 dots or more, 32,000 colors or more Installing the software You can install the software (supplied) using the following procedure. x Windows • Log on as Administrator. 1 Turn on your computer, and insert the CD-ROM (supplied) into the CD-ROM drive. The installation menu screen appears. • If it does not appear, double-click (My Computer) t (SONYPICTUTIL) t [Install.exe]. • Under Windows Vista, the AutoPlay screen may appear. Select “Run Install.
3 Remove the CD-ROM after the installation is complete. The following software is installed and shortcut icons appear on the desktop. • Sony Picture Utility “Picture Motion Browser” • Sony Image Data Suite “Image Data Converter SR” “Image Data Lightbox SR” After you install the software, a shortcut icon for the customers registration website is created on the desktop. Once you register on the website, you can get secure and useful customer support. http://www.sony.
Using “Picture Motion Browser” Note • “Picture Motion Browser” is not compatible with Macintosh computers. With “Picture Motion Browser” you can: • Import images shot with the camera and display them on the computer. • Organize images on the computer on a calendar by shooting date to view them. • Retouch (Red Eye Correction, etc.), print, and send still images as e-mail attachments, change the shooting date and more. • Print or save still images with the date.
Using “Image Data Converter SR” Note • If you save an image as RAW data, the image is saved in the ARW2.0 format. With “Image Data Converter SR Ver.2.0” you can: • Edit images recorded in RAW mode with various corrections, such as tone curve, and sharpness. • Adjust images with the white balance, exposure, and creative style, etc. • Save the images displayed and edited on a computer. You can either save the image as RAW data or save it in the general file format.
Using “Image Data Lightbox SR” With “Image Data Lightbox SR” you can: • Display and compare RAW/JPEG images recorded with this camera. • Rate the images on a scale of five. • Display an image in “Image Data Converter SR” and make adjustments to it. • For details on “Image Data Lightbox SR,” refer to the Guide. To start the Guide from the Start menu, click [Start] t [All Programs] (in Windows 2000, [Programs]) t [Sony Image Data Suite] t [Help] t [Image Data Lightbox SR].
Printing images Specifying DPOF Using the camera, you can specify the images and the number of images to print before you print images at a shop or with your printer. Follow the procedure below. DPOF specifications are left with images after printing. It is recommended that you unspecify them after printing. Specifying /unspecifying DPOF on selected images 1 MENU button t 1 t [DPOF setup] t [Marked images] An image is displayed on the single screen. 2 Select the image with b/B on the controller.
Dating images You can date images when printing them. The position of the date (inside or outside the image, character size, etc.) depends on your printer. MENU button t [On] 1 t [DPOF setup] t [Date imprint] t Note • This function may not provided, depending on the printer. Creating an index print You can create an index print of all the images in the memory card.
Printing images by connecting the camera to a PictBridge compliant printer Even if you do not have a computer, you can print images shot using your camera by connecting the camera directly to a PictBridge compliant printer. “PictBridge” is based on the CIPA standard. (CIPA: Camera & Imaging Products Association) Note • You cannot print RAW data files.
Stage 2: Connecting the camera to the printer 1 Connect the camera to the printer. 1 To the USB terminal USB cable 2 To the USB terminal 2 Turn on your camera and the printer. The screen used for selecting images you want to print appears. Stage 3: Printing 1 Select the image to print with b/B on the controller, then press the center of the controller. • To cancel, press the center again. 2 Repeat step 1 if you want to print other images. 3 Press the MENU button and set up each item.
To cancel the print During printing, pressing the center of the controller cancels the print. Remove the USB cable or turn off the camera. When you want to print again, follow the procedure (Stages 1 to 3) above. PictBridge menu Page 1 Print Prints the selected images. For details, see “Stage 3: Printing.” Set print q’ty You can specify the number of prints, up to 20. The same number of prints is specified on all the selected images. Paper size Auto Printer setup 9×13cm/3.
Layout Auto Printer setup 1-up/Borderless Borderless, 1 image/sheet 1-up 1 image/sheet 2-up 2 images/sheet 3-up 3 images/sheet 4-up 4 images/sheet 8-up 8 images/sheet Index Prints all the selected images as an index print. Printing layout follows the printer setup. Date imprint Day and time Attaches the date and time. Date Attaches the date. Off Does not attach the date. Page 2 Unmark all After the message appears, select [OK], then press the center of the controller.
Others Specifications [Super SteadyShot] Camera Super SteadyShot Compensation capability Approximately 2.5 to 3.5 EV decrease in shutter speed (varies according to shooting conditions and lens used) [System] Camera Type Digital Single Lens Reflex Camera with built-in flash and interchangeable lenses Lens All of α Lens [Image sensor] Total pixel number of camera DSLR-A350 Approx. 14 900 000 pixels DSLR-A300 Approx. 10 800 000 pixels Effective pixel number of camera DSLR-A350 Approx.
[Viewfinder] [Built-In-Flash] Type Flash G.No. Fixed eye-level pentaDach-mirror Field of View 0.95 Magnification 0.74 × with 50 mm lens at infinity, –1 m–1 Eye Relief Approximately 20.8 mm from the eyepiece, 16.7 mm from the eyepiece frame at –1 diopter (–1 m–1) Dioptor Adjustment –3.0 to +1.0 m–1 GN 12 (in meters at ISO 100) Recycling time Approx. 4 seconds Flash coverage Covering 18 mm lens (focal length that the lens indicates) Flash compensation ±2.
Mass Approx.582 g (1 lb 4.5 oz) (without batteries, memory card and body accessories) Operating temperature 0 to 40°C (32 to 104°F) (When using the Microdrive: 5 to 40°C (41 to 104°F)) Exif Exif Ver.2.21 USB communication Hi-Speed USB (USB 2.0 compliant) BC-VM10 Battery charger Input rating 100 V – 240 V AC, 50/60 Hz Output rating 8.4 V DC, 750 mA Operating temperature range 0 to 40°C (32 to 104°F) Storage temperature range –20 to +60°C (–4 to +140°F) Maximum dimensions Approx.
Trademarks • is a trademark of Sony Corporation. • “Memory Stick,” , “Memory Stick PRO,” , “Memory Stick Duo,” , “Memory Stick PRO Duo,” , “Memory Stick PRO-HG Duo,” , “Memory Stick Micro,” “MagicGate,” and are trademarks of Sony Corporation. • “InfoLITHIUM” is a trademark of Sony Corporation. • Microsoft, Windows, and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Troubleshooting If you experience trouble with your camera, try the following solutions. Check the items on pages 151 to 160. Consult your Sony dealer or local authorized Sony service facility. 1 Check the following items. 2 Remove the battery pack, and insert the battery pack again after about one minute, and turn on the power. 3 Reset the settings (page 124). 4 Consult your Sony dealer or local authorized Sony service facility. Battery pack and power The battery pack cannot be installed.
The power turns off suddenly. • If you do not operate the camera for given period of time, the camera turns to power saving mode and nearly shuts down. To cancel the power save, operate the camera, such as pressing the shutter button halfway down (page 121). Shooting images Nothing is displayed on the LCD monitor in viewfinder mode when the power is turned on.
• You try to shoot a subject that may require special focusing (page 73). Use the focus-lock or manual focus function (pages 73, 75). Recording takes a long time. • The noise reduction function is turned on (page 118). This is not a malfunction. • You are shooting in RAW mode (page 115). Since the RAW data file is large, the RAW mode shooting may take time. The image is out of focus. • The subject is too close. Check the minimum focal distance of the lens.
The aperture value and/or shutter speed flash when you press the shutter button halfway down. • Since the subject is too bright or too dark, it is beyond the available range of the camera. Adjust the setting again. The image is whitish (Flare). Blurring of light appears on the image (Ghosting). • The picture was taken under a strong light source, and excessive light has entered the lens. Attach a lens hood. The corners of the picture are too dark.
The color of an image recorded in Live view mode is strange. • In Live view mode, carefully check the image displayed on the LCD monitor before shooting. The camera may not be able to recognize the color of the image right after switching to the Live view mode. In such cases, the expected result may not be obtained. Viewing images Your camera cannot play back images. • The folder/file name has been changed on your computer (page 133).
Your computer does not recognize your camera. • Check that the camera is turned on. • When the battery level is low, install the charged battery pack (page 16), or use the AC Adaptor/charger (not supplied). • Use the USB cable (supplied) (page 128). • Disconnect the USB cable, and connect it again firmly. • Set [USB connection] to [Mass Storage] (page 128). • Disconnect all equipment other than the camera, the keyboard and the mouse from the USB jacks of your computer.
Cannot record on a memory card. • The memory card is full. Delete unnecessary images (page 110). • An unusable memory card is inserted (page 21). • You are using the memory card with the write-protect switch, and the switch is set to the LOCK position. Set the switch to the recording position. The Microdrive is heated. • You are using the Microdrive for a long time. This is not a malfunction. You have formatted a memory card by mistake. • All the data on the memory card is deleted by formatting.
Cannot print images with the date. • Using “Picture Motion Browser,” you can print images with date (page 138). • This camera does not have a feature for superimposing dates on images. However, because the images shot with the camera include information on the recording date, you can print images with the date superimposed if the printer or the software can recognize Exif information. For compatibility with Exif information, consult the manufacturer of the printer or the software.
Cannot print the image at the size selected. • Disconnect the USB cable and reconnect it whenever you change the paper size after the printer has been connected to the camera. • The print setting of the camera differs from that of the printer. Change the setting of either the camera (page 144) or the printer. Cannot operate the camera after canceling printing. • Wait for a while as the printer is carrying out the cancellation. It may take some time depending on the printer. Others The lens gets fogged.
The five bars of the Super SteadyShot scale flash. • The Super SteadyShot function does not work. You can continue to shoot but the Super SteadyShot function will not work. Turn the camera off and on. If the Super SteadyShot scale continues to flash, consult your Sony dealer or local authorized Sony service facility. “--E-” is indicated on the screen. • Remove the memory card, and insert it again. If this procedure does not turn off the indication, format the memory card.
Warning messages If the following messages appear, follow the instructions. If the message still appears, change the memory card. Card error • An incompatible memory card is inserted or the format was failed. For “InfoLITHIUM” battery only • An incompatible battery pack is being used (page 17). Set date and time? • Set the date and time. If you have not used the camera for a long time, charge the internal rechargeable battery (pages 25, 163).
No images • There is no image in the memory card. Unable to magnify. Unable to rotate image. • Images recorded with other cameras may not be enlarged or rotated. Image protected • You tried to delete protected images. Unable to print. • You tried to mark RAW images with a DPOF mark. Initializing USB connection... • A USB connection has been established. Do not disconnect the USB cable. Check the connected device. • A PictBridge connection cannot be established.
Precautions or hot places that exceed this range is not recommended. Do not use/store the camera in the following places On moisture condensation • In an extremely hot, dry or humid place In places such as in a car parked in the sun, the camera body may become deformed and this may cause a malfunction. • Under direct sunlight or near a heater The camera body may become discolored or deformed, and this may cause a malfunction.
discharged. In this case, be sure to charge this rechargeable battery before using the camera. However, even if this rechargeable battery is not charged, you can still use the camera as long as you do not record the date and time. If the camera resets the settings to the defaults each time you charge the internal rechargeable battery, the battery may be dead. Consult your Sony dealer or local authorized Sony service facility.
Index Index Numerics 40-segment honeycomb pattern metering ............................... 148 A Adobe RGB................................ 95 AE lock ...................................... 83 AEL button .............................. 120 AF area....................................... 75 AF illuminator............................ 80 Ambient bracket....................... 100 Amount of exposure................... 56 Anti-dust function ...................... 32 Aperture ...............................
Exposure compensation..............85 Exposure lock .............................83 Exposure mode ...........................56 Eyecup ........................................27 Eyepiece cover............................27 Eyepiece sensors.........................28 Eye-Start AF ...............................67 Image size ................................ 114 Index print................................ 142 Index screen ............................. 104 Info.disp.time ...........................
Night view.................................. 55 Noise reduction ........................ 118 Number of recordable images ......................................... 29, 30 P PictBridge ................................ 143 Picture Motion Browser........... 138 Pixel mapping .......................... 154 PlaybackDisplay ...................... 101 Portrait ....................................... 50 Power save ............................... 121 Preset white balance................... 91 Pressing halfway down .