Beo4 and Beolink 1000 are remote control terminals from Bang & Olufsen. OneRemote supplies interface modules that allow third party equipment to be operated via a Bang & Olufsen remote control system. Beocompatible Operation via Oneremote Interface Type 6124 Sony Flat screen TV RM-ED009 / RM-ED010 / RM-ED011 / RM-ED012 / RM-ED013 6124UKu1 Made in Denmark by www.oneremote.
Operating with Beo4 and Beo5 Beo4/ Beo5 Daily operation Beo4 and Beo5 do not have as many keys as this TV’s original remote control. Thus certain Beo4/ Beo5 keys have got alternative functionality. OO o1 o2 OK Analog Digital W*2 *1 R*2 *1 Q*2 E*2 P+ PGuide Return m om e w Home Options Back Power off To get to this Ohas to be pressed first, i.e. Ofollowed by 0on corresponds to info on the TV’s own remote control.
Congratulations With your bee2 controller from www.oneremote.dk you now can fully operate your Sony TV using your Bang & Olufsen remote control terminal, via a beeLINK system bus. Beolink1000, Beo4 or Beo5 remote controls can be used. This guide explains how. This BeeLINK2 controller is ready for use, plug & play. See the opposite page regarding daily operation. Some operations can be altered, to improve interaction with other controllers or to your convenience.
BeeLINK - How it works The OneRemote beeLINK system is based on a 455 khz IR-receiver placed in the room. Via a beeLINK amplifier it can distribute control data to many different beeLINK controllers or BeeLINK compatible devices, each designed for a specific purpose. One controller is used for the TV, another controller for the DVD, a third for a beamer and so on. The BeeLINK system lets you control many devices, in a logic way.
BeeLINK basics – the link amplifier. To receive the IR data emitted from a Bang & Olufsen remote control, a B&O IR-receiver is often used. If there is already one IR-receiver in the room, this can also be used to feed the BeeLINK bus. Normally there is no need for two IR receivers in the same room. A Bang & Olufsen IR-receiver connected to the BeeLINK link amplifier with four BeeLINK outputs. Four BeeLINK controllers can be connected to this link amplifier.
The BeeLINK bus is a parallel bus type. Passive splitters therefore can be used, to make a network of any shape. If many controllers or very long cables are used, it might be necessary to place one more or more power supplies, placed closer to the controllers that lack power. Using this parallel structure each BeeLINK controller receives the IR-data at the same time. Every controller has its own microcomputer, living its own life.
BeeLINK2 connections. The IR/ sense socket is output for the IR-emitter that sends IR to the device to be operated. In some cases this socket is also used for sensing purposes. Often the BeeLINK2 controller needs to know if the device is powered up or not. In some cases this socket is used for other serial communication like RS-232. Prog switch is a push button that must be activated to initiate a programming sequence, as described in the option programming chapters.
BeeLINK Active option. As all controllers on the BeeLINK bus are receiving all the IR-data at the same time, every controller must know when to go active and when to go inactive. Sometimes two or more controllers are active at the same time. A BeeLINK 2 controller is used to operate a TV, a satellite receiver, a DVD-player, a projector or similar devices. Each controller is specifically made for one device.
BeeLINK source option. The BeeLINK active option sets which source button on the remote control, that makes the BeeLINK2 go active and turns on the TV, as described in the previous chapter. The BeeLINK source option combines other source buttons on the remote control, with the input sockets on the TV. The source option can force the TV to open a specific input, when another source is selected.
Programme Zapping option The buttonsW ,R,D andFare being used for programme stepping and to manoeuvre up and down in an on screen menu. This is the basic OneRemote layout and compatible with other OneRemote controllers. Some people prefer the programme zapping buttons on the up and down buttons. The programme zapping option, make it possible to change the function of these buttons.