Preparing the camera Before your operation Shooting images Using the shooting function Using the viewing function Changing your setup Viewing images on a computer Printing images Additional information on this product and answers to frequently asked questions can be found at our Customer Support Website. Digital Single Lens Reflex Camera Instruction Manual DSLR-A330/A380 Printed on 70% or more recycled paper using VOC (Volatile Organic Compound)-free vegetable oil based ink.
Owner’s Record The model and serial numbers are located on the bottom. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. DSLR-A330/A380 Serial No. __________________________ WARNING To reduce fire or shock hazard, do not expose the unit to rain or moisture. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS. DANGER - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS.
• Keep the battery pack out of the reach of small children. • Keep the battery pack dry. • Replace only with the same or equivalent type recommended by Sony. • Dispose of used battery pack promptly described the instructions. Battery charger Even if the CHARGE lamp is not lit, the battery charger is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet (wall socket).
Regulatory Information Declaration of Conformity Trade Name: SONY Model No.: DSLR-A330 Responsible Party: Sony Electronics Inc. Address:16530 Via Esprillo, San Diego, CA 92127 U.S.A. Telephone No.: 858-942-2230 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For Customers in Europe Notice for the customers in the countries applying EU Directives The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.
Disposal of waste batteries (applicable in the European Union and other European countries with separate collection systems) This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste. By ensuring these batteries are disposed of correctly, you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of the battery.
Notes on using your camera Shooting procedure • This camera has two modes for shooting: the Live View mode using the LCD monitor, and the viewfinder mode using the viewfinder (OVF). • There may be differences between an image recorded in Live View mode and an image recorded in viewfinder mode, such as exposure, white balance, or Drange optimizer, depending on the method used of metering or the exposure mode.
On the data specifications described in this Instruction Manual The data on performance and specifications is defined under the following conditions, except as described in this Instruction Manual: at an ordinary ambient temperature of 25ºC (77°F), and using a fully charged battery pack.
Table of Contents Notes on using your camera .............................................. 7 Preparing the camera Checking the accessories supplied .................................. 13 Preparing the battery pack ............................................... 14 Attaching a lens ............................................................... 20 Inserting a memory card .................................................. 22 Preparing the camera .......................................................
Shooting an image the way you want it (Exposure mode) ..................................................................................... 57 Shooting with program auto .................................. 59 Shooting by controlling the blur of the background (Aperture priority) ............................................. 60 Shooting a moving subject with various expressions (Shutter speed priority) ..................................... 62 Shooting with the exposure adjusted manually (Manual exposure) ....
Setting ISO ...................................................................... 92 Adjusting the color tones (White balance) ...................... 93 Adjusting the white balance to suit a specific light source (Auto/Preset white balance) .............................. 93 Registering the color tones (Custom white balance) .. 94 Image processing ............................................................. 96 Correcting the brightness of the image (D-Range Optimizer) ......................................
Others Specifications ................................................................ 150 Troubleshooting ............................................................. 154 Warning messages ......................................................... 164 Precautions .................................................................... 167 Index ..............................................................................
Preparing the camera Checking the accessories supplied The number in parentheses indicates the number of pieces. • Body cap (1) (Attached on the camera) • Power cord (mains lead) (1) (not supplied in the U.S.A.
Preparing the battery pack When using the camera for the first time, be sure to charge the NP-FH50 “InfoLITHIUM” battery pack (supplied). Charging the battery pack The “InfoLITHIUM” battery pack can be charged even when it has not been fully depleted. It can also be used when it has not been fully charged. 1 Insert the battery pack on the battery charger. Push the battery pack until it clicks.
2 Connect the battery charger to the wall outlet (wall socket). Plug To the wall outlet (wall socket) CHARGE lamp For customers in countries/regions other than the U.S.A. and Canada Power cord (mains lead) CHARGE lamp About charging time • Time required to charge a fully depleted battery pack (supplied) at a temperature of 25°C (77°F) is as follows. Full charge Normal charge Approx. 265 min. Approx. 205 min.
• When the CHARGE lamp flashes fast, remove the battery pack being charged, and then insert the same battery pack into the battery charger securely again. When the CHARGE lamp flashes fast again, this may indicate a battery error or that a battery pack other than the specified type has been inserted. Check that the battery pack is the specified type.
Inserting the charged battery pack 1 While sliding the battery cover Preparing the camera open lever, open the battery cover. 2 Firmly insert the battery pack all the way while pressing the lock lever with the tip of the battery. Lock lever 3 Close the battery cover. To remove the battery pack Turn off the camera and slide the lock lever in the direction of the arrow. Be careful not to drop the battery pack.
To check the remaining battery level Set the power switch to ON and check the level on the LCD monitor. “Battery exhausted” Battery level High Low You cannot shoot any more pictures. What is an “InfoLITHIUM” battery pack? An “InfoLITHIUM” battery pack is a lithium-ion battery pack that has functions for exchanging information related to operating conditions with your camera. Notes • The displayed level may not be correct under certain circumstances. • Do not expose the battery pack to water.
• The battery life varies according to how it is stored and the operating conditions and environment in which each battery pack is used. 19 Preparing the camera How to store the battery pack If the battery pack is not to be used for a long time, fully charge it and then fully use it up once a year on your camera before storing the battery pack in a dry, cool place to prolong the battery life.
Attaching a lens 1 Remove the body cap from the camera and the packaging lid from the rear of the lens. • When changing the lens, quickly change the lens away from dusty locations so as to keep dust or debris from getting inside the camera. Body cap Packaging lid 2 Mount the lens by aligning the orange index marks on the lens and camera. Orange index marks 3 Turn the lens clockwise until it clicks into the locked position. Notes • A rear lens cap is not supplied with the DT 18-55mm F3.5-5.
To remove the lens 1 Press the lens release button all the way in and turn the lens counterclockwise until it stops. 2 Replace the packaging lid on the lens and attach the body cap to the camera. • Before you attach them, remove dust from them. • When you purchase the DT 18 – 55 mm F3.5 – 5.6 SAM Lens Kit, purchase the Rear Lens Cap ALC-R55 also.
Inserting a memory card Only “Memory Stick PRO Duo” media, “Memory Stick PRO-HG Duo” media, SD memory cards and SDHC memory cards can be used with this camera. A MultiMediaCard cannot be used with this camera. The “Memory Stick PRO Duo” media and “Memory Stick PRO-HG Duo” media are referred to as the “Memory Stick PRO Duo” media and the SD memory card and SDHC memory card are referred to as the “SD memory card” in this Instruction Manual. 1 Open the memory card cover.
4 Close the memory card cover. To remove the memory card Access lamp Notes on using memory cards • Do not strike, bend or drop the memory card. • Do not use or store the memory card under the following conditions: – High temperature locations such as the hot interior of a car parked in direct sunlight. – Locations exposed to direct sunlight. – Humid locations or locations with corrosive substances present. • The memory card may be hot just after it has been used for a long time.
• The “Memory Stick PRO Duo” media with a capacity up to 16 GB or the SD memory cards with a capacity up to 32 GB have been confirmed to operate properly with this camera. • The memory cards formatted with a computer are not guaranteed to operate with this camera. • Data read/write speeds differ depending on the combination of the memory cards and the equipment used. • Do not press down hard when you write down on the memo area. • Do not attach a label on the memory cards themselves.
Preparing the camera Setting up the date 1 Set the power switch to ON to turn the camera on. • To turn the camera off, set it to OFF. 2 Verify that [OK] is selected on the LCD monitor, then press the center of the control button. 3 Select each item with b/B and set the numeric value with v/V. • When changing the sequence of [YYYY/MM/DD], first select [YYYY/ MM/DD] with b/B, then change it with v/V. 4 Repeat step 3 to set other items, then press the center of the control button.
5 Verify that [OK] is selected, then press the center of the control button. To cancel the date/time setting operation Press the MENU button.
Using the accessories supplied Attaching the shoulder strap Attach both ends of the strap onto the camera. Eyepiece cover • You can also attach the eyepiece cover (page 28) on the strap. 27 Preparing the camera This section describes how to use the shoulder strap, the eyepiece cover, and eyecup. The other accessories are described in the following pages. • Rechargeable battery pack (page 14) • Battery charger (page 14) • Power cord (mains lead) (not supplied in the U.S.A.
Using the eyepiece cover and eyecup You can prevent light from entering through the viewfinder and affecting the exposure. When the shutter is released without the use of the viewfinder in viewfinder mode, as in shooting with the self-timer, attach the eyepiece cover. 1 Tilt the LCD monitor downward. 2 Carefully slide the eyecup off by pushing on each side of the eyecup. • Put your fingers under the eyecup, and slide it upward. 3 Slide the eyepiece cover over the viewfinder.
Checking the number of recordable images Notes • When “0” (the number of recordable images) flashes in yellow, the memory card is full. Replace the memory card with another one, or delete images in the current memory card (page 112). • When “NO CARD” (the number of recordable images) flashes in yellow, it means no memory card has been inserted. Insert a memory card.
DSLR-A330 Capacity (Units: Images) 1GB 2GB 4GB 8GB 320 647 1281 2575 5221 Fine 237 480 951 1910 3874 RAW & JPEG 48 98 195 392 797 RAW 60 123 245 494 1004 Size Standard SD memory card DSLR-A380 Capacity Size Standard 16GB (Units: Images) 1GB 2GB 4GB 8GB 16GB 270 537 1081 2177 4421 Fine 193 385 776 1564 3176 RAW & JPEG 35 71 144 291 592 RAW 43 87 177 358 728 DSLR-A330 Capacity Size Standard (Units: Images) 1GB 2GB 4GB 8GB 16GB 319 634 1277 25
The number of images that can be recorded using a battery pack DSLR-A380 DSLR-A330 Live View mode Approx. 230 images Approx. 230 images Viewfinder mode Approx. 500 images Approx. 510 images • The number is calculated with a battery pack at full capacity and in the following situation: – At an ambient temperature of 25°C (77°F). – [Quality] is set to [Fine]. – [Autofocus mode] is set to (Automatic AF). – Shooting once every 30 seconds. – The flash strobes once every two times.
Cleaning Cleaning the LCD monitor Wipe the screen surface with a commercially available LCD cleaning kit to remove fingerprints, dust, etc. Cleaning the lens • When cleaning the lens surface, remove dust using a commercially available blower. In case of dust that sticks to the surface, wipe it off with a soft cloth or tissue paper slightly moistened with lens cleaning solution. Wipe in a spiral pattern from the center to the outside. Do not spray lens cleaning solution directly onto the lens surface.
Cleaning the image sensor Notes • Cleaning can be performed only when the battery level is (three remaining battery icons) or more. Low battery power during cleaning can cause damage to the shutter. The cleaning should be completed quickly. The use of an AC-PW10AM AC Adaptor (sold separately) is recommended. • Do not use a spray blower because it may scatter water droplets inside the camera body. 1 Confirm that the battery is fully charged (page 18).
5 Detach the lens (page 21). 6 Use the blower to clean the image sensor surface and the surrounding area. • Do not touch the image sensor with the tip of the blower. Complete the cleaning quickly. • Hold the camera’s face downward to prevent the dust from resettling in the camera. • When cleaning the image sensor, do not put the tip of a blower into the cavity beyond the mount. 7 Attach the lens and turn the camera off. Note • The camera starts beeping if the battery pack becomes low during cleaning.
Before your operation Identifying parts and screen indicators See the pages in parentheses for details of operation. Front side Before your operation A Shutter button (48) M Focus mode switch (76, 81) B Power switch (25) * Do not directly touch these parts.
Rear side A Accessory shoe (87) M Control button When the menu is turned on: v/ V/b/B (40) When the menu is turned off: DISP (39, 70, 104)/ (99)/ ISO (92)/ (84) B Viewfinder* (68) C MENU button (42) D Eyepiece sensors (68, 127) E LCD monitor (38, 44, 104, 108) F Light sensor (126) G Diopter-adjustment dial (69) H LIVE VIEW/OVF switch (68) I (Smart teleconverter) button (82) J For shooting: button (88) For viewing: button (105) (Exposure) (Zoom in) K Fn (Function) button (42) L Control button (Enter
Sides/Bottom B Memory card switch C Memory card cover D “Memory Stick PRO Duo” media insertion slot (22) E SD memory card insertion slot K Tripod receptacle • Use a tripod with a screw length of less than 5.5 mm (7/32 inch). You will be unable to firmly secure the camera to tripods having screws longer than 5.5 mm (7/32 inch), and may damage the camera.
LCD monitor The indicators on the monitor are displayed as follows in Live View mode. For the indicators in viewfinder mode, see page 71. A B Display Indication Display Remaining battery (18) ×1.
C Display Indication z Focus (77) 1/125 Shutter speed (62) F3.5 Aperture (60) EV scale (65, 102) Camera shake warning (46) Before your operation SteadyShot scale (46) To switch the recording information display Each time you press DISP on the control button, the screen changes as follows.
Selecting a function/setting You can select a function for shooting or playback from the menu list. To display the menu list, press the control button, Fn (Function) button, or MENU button. Example: When the Fn button is pressed. From the menu list, use the control button to move the cursor to the setting of your choice and execute the selection. : Press v/V/b/B on the control button to move the cursor. z: Press the center button to execute the selection.
2 Select [White balance] with v/V/ b/B on the control button, then press the center z to execute. 3 Following the operation guide, For example, to change , select with v/V, adjust the value to +/– with b/B, then press the center z to execute. Operation guide The operation guide list The operation guide also indicates operations other than the control button operation. The indications of icons are as follows.
• • • • • Continuous adv. (page 99) Self-timer (page 100) Self-timer(Cont.) (page 100) Bracket: Cont. (page 101) Remote Commander (page 103) The functions selected by the Fn (Function) button This button calls up the screens that are used for setting up or executing functions used frequently in shooting or viewing.
Playback menu Delete (112) Format (121) Slide show (107) 1 Protect (111) Specify Printing (145) PlaybackDisplay (104) Setup menu Date/Time setup (125) Language (125) File number (120) 2 Folder name (120) Select folder (121) • New folder (121) Before your operation LCD brightness (126) Power Save (LV) (124) Power Save (OVF) (124) 1 CTRL FOR HDMI (116) Display Color (124) Help Guide disp.
Shooting images Adjusting the angle of the LCD monitor You can adjust the angle of the LCD monitor to meet various shooting situations. You can shoot from various shooting positions. Low position Adjust the LCD monitor to an easily viewable angle.
Shooting an image without camera shake “Camera shake” refers to unwanted movement of the camera that occurs after the shutter button has been pressed, resulting in a blurred image. To reduce camera shake, follow the instructions below. Correct posture Stabilize your upper body and take a position that keeps the camera from moving. Shooting images In Live View mode In viewfinder mode Point 1 One hand holds the grip of the camera, and the other hand supports the lens.
Point 3 Lightly tuck your elbows against your body. When shooting in a kneeling position, steady your upper body by placing your elbow on your knee. Camera shake warning indicator Due to potential camera shake, the (Camera shake warning) indicator flashes. In this case, use a tripod or the flash. (Camera shake warning) indicator Note • The (Camera shake warning) indicator is displayed only in the modes that automatically set the shutter speed. This indicator is not displayed in M/S modes.
Note • The SteadyShot function may not work optimally when the power has just been turned on or when the shutter button has been pressed all the way down without stopping halfway. Wait for the (SteadyShot scale) indicator scale to go down, and then press the shutter button down slowly. Using a tripod Note • When using a tripod, deactivate the SteadyShot function because there is a potential for malfunction of the SteadyShot function (page 46).
/ Shooting with the automatic setting The “AUTO” mode allows you to easily shoot any subject under any conditions because the camera makes appropriate judgments on the situation to adjust the settings. Select when shooting in a location where the use of a flash is restricted. When you turn the mode dial, the explanation of the selected mode and methods of shooting are displayed on the screen (Help Guide disp.). You can clear the Help Guide (page 124). 1 Set the mode dial to or (Flash Off).
5 Press the shutter button halfway down to focus. When the focus is confirmed, z or (Focus indicator) lights up (page 77). Shooting images Focus indicator 6 Press the shutter button fully down to shoot. • Pressing the shutter button after the (SteadyShot scale) indicator becomes low makes the SteadyShot function more effective. (SteadyShot scale) indicator Note • Since the camera turns on the automatic setting function, many features will be unavailable, such as exposure compensation, ISO setting.
Shooting with a suitable setting for the subject (Scene Selection) Selecting an appropriate mode for the subject or the shooting conditions allows you to shoot the image with a suitable setting for the subject. When you turn the mode dial, the explanation of the selected mode and methods of shooting are displayed on the screen (Help Guide disp.). You can clear the Help Guide (page 124). Note • The camera makes appropriate judgments on the situation to adjust the settings.
Taking portrait photos This mode is suitable for z Blurring away backgrounds and sharpening the subject. z Expressing skin tones softly. Shooting images Set the mode dial to (Portrait). Shooting techniques • To blur the background more, set the lens to the telephoto position. • You can shoot a vivid image by focusing on the eye that is closer to the lens. • Use the lens hood (sold separately) to shoot backlit subjects.
Taking landscape photos This mode is suitable for z Shooting the entire range of scenery in sharp focus with vivid colors. Set the mode dial to (Landscape). Shooting techniques • To accentuate the openness of the scenery, set the lens to wide angle. • Set the flash mode to (Fill-flash) when you shoot with the flash (page 84).
Taking small-subject photos This mode is suitable for z Shooting close subjects such as flowers, insects, dishes, or small goods. Shooting images Set the mode dial to (Macro). Shooting techniques • Get close to the subject and shoot at the minimum distance of the lens. • You can shoot a closer subject using a macro lens (sold separately). • Set the flash mode to (Flash Off) when you shoot a subject within 1 m (3.3 feet).
Taking moving-subject photos This mode is suitable for z Shooting moving subjects outdoors or in bright places. Set the mode dial to (Sports Action). Shooting techniques • The camera shoots images continuously while the shutter button is pressed. • Press and hold the shutter button halfway down until the right moment. • Set the flash mode to (Fill-flash) when you shoot with the flash (page 84).
Taking sunset photos This mode is suitable for z Shooting the red of the sunset beautifully. Shooting images Set the mode dial to (Sunset). Shooting techniques • Used to shoot an image accentuating the red color compared with other modes. This is also suitable for shooting the beautiful red of the sunrise. • Set the flash mode to (Fill-flash) when you shoot with the flash (page 84).
Taking night view photos This mode is suitable for z Shooting portraits in night scenes. z Shooting night scenes at a distance without losing the dark atmosphere of the surroundings. Set the mode dial to Set the flash mode to persons (page 84). (Night Port./View). (Flash Off) when you shoot a night view without Shooting techniques • Take care that the subject does not move to prevent the image from blurring. • The shutter speed is slower, so using a tripod is recommended.
Shooting an image the way you want it (Exposure mode) With a single lens reflex camera, you can adjust the shutter speed (how long the shutter is open) and aperture (the range that is in focus: depth of field) to enjoy a variety of photographic expressions. For example, you can use a fast shutter speed to shoot the ephemeral shape of a wave, or you can accentuate a flower by opening the aperture to put everything in front of and beyond the flower out of focus.
When you turn the mode dial, the explanation of the selected mode and methods of shooting are displayed on the screen (Help Guide disp.). You can clear the Help Guide (page 124).
Shooting with program auto This mode is suitable for z Using the automatic exposure, while keeping the custom settings for ISO sensitivity, Creative Style, D-Range optimizer, etc. 2 Set the shooting functions to your desired settings (pages 76 to 103). • Set the flash mode to (page 84). (Fill-flash) when you shoot with the flash 3 Adjust the focus and shoot the subject. 59 Shooting images 1 Set the mode dial to P.
Shooting by controlling the blur of the background (Aperture priority) This mode is suitable for z Putting the subject in sharp focus and blur everything in front of and beyond the subject. Opening the aperture narrows the range that is in focus. (Depth of field becomes shallower.) z Shooting the depth of the scenery. Narrowing down the aperture widens the range that is in focus. (Depth of field becomes deeper.) 1 Set the mode dial to A.
2 Select the aperture value (Fnumber) with the control dial. • Smaller F-number: The foreground and background of the subject are blurred. Larger F-number: The subject and its foreground and background are all in focus. • You cannot check the blurring of an image on the LCD monitor or in the viewfinder. Check the recorded image and adjust the aperture. 3 Adjust the focus and shoot the subject. The shutter speed is automatically adjusted to obtain correct exposure.
Shooting a moving subject with various expressions (Shutter speed priority) This mode is suitable for z Shooting a moving subject at a moment in time. Use a faster shutter speed to crisply shoot an instant of the movement. z Tracing the movement to express the dynamism and flow. Use a slower shutter speed to shoot a trailing image of the moving subject. 1 Set the mode dial to S.
2 Select the shutter speed with the control dial. Shooting images Shutter speed 3 Adjust the focus and shoot the subject. The aperture is automatically adjusted to obtain correct exposure. • When the camera judges that the proper exposure is not obtained with the selected shutter speed, the aperture value flashes. In such cases, adjust the shutter speed again. Aperture (F-number) Shooting techniques • When the shutter speed is slower, use a tripod.
Shooting with the exposure adjusted manually (Manual exposure) This mode is suitable for z Shooting with the desired exposure setting by adjusting both the shutter speed and aperture. 1 Set the mode dial to M. 2 Rotate the control dial to adjust the shutter speed, and while pressing the button, rotate the control dial to adjust the aperture. • You can select the item the control dial adjusts (shutter speed or aperture) with [Ctrl dial setup] (page 123).
3 Shoot the image after the exposure is set. • Check the exposure value on the EV scale. Toward +: Images become brighter. Toward –: Images become darker. The b B arrow appears if the set exposure is beyond the range of the EV scale. The arrow starts flashing if the difference becomes greater. Standard value 65 Shooting images Notes • The (Camera shake warning) indicator is not indicated in manual exposure mode. • When the mode dial is set to M, the ISO setting [AUTO] is set to [100].
Shooting trails with long exposure (BULB) This mode is suitable for z Shooting trails of light, such as fireworks. z Shooting trails of stars. 1 Set the mode dial to M. 2 Rotate the control dial to the left until [BULB] is indicated. BULB 3 While pressing the button, rotate the control dial to adjust the aperture (F-number).
4 Press the shutter button halfway down to adjust the focus. 5 Press and hold the shutter button for the duration of the shooting. As long as the shutter button is pressed, the shutter remains open. Shooting techniques Notes • When using a tripod, turn off the SteadyShot function (page 46). • The longer the exposure time, the more conspicuous the noise on the image. • After shooting, noise reduction (Long exp.NR) will be done for the same amount of time that the shutter was open.
Shooting with the viewfinder (OVF) You can select either the LCD monitor (Live View) or the viewfinder (OVF) to shoot images. Switching to the viewfinder Set the LIVE VIEW/OVF switch to “OVF.” The screen status changes as follows: Viewfinder display LCD monitor display When you look into the viewfinder, the subject inside the focus area comes into focus automatically (Eye-Start AF).
Adjusting the focus of the finder (diopter adjustment) Adjust the diopter-adjustment dial to your eyesight until the indicators appear clearly in the viewfinder. • Turn the dial toward + when you are farsighted, toward – when you are near-sighted. • Training the camera on a light allows you to adjust the diopter easily. Shooting images When it is hard to rotate the diopter-adjustment dial Put your fingers under the eyecup, and slide it upward to remove the eyecup, then adjust the diopter.
Switching the recording information display (DISP) Press DISP on the control button to switch between the Graphic Display and the Standard Display. When you rotate the camera to a vertical position, the display automatically rotates to adjust to the camera position.
LCD monitor (Graphic Display) The Graphic Display graphically shows the shutter speed and aperture value and clearly illustrates how the exposure works. In AUTO or Scene Selection mode, only the items that can be set are displayed. See the pages in parentheses for details of operation. Shooting images C A Display Indication Display P A S M Mode dial (48 – 67) 1/125 Shutter speed (62) F5.
D Display Indication Remaining battery (18) Image quality (119) Image size (118)/Aspect ratio (118) Memory card (22) 100 72 Remaining number of recordable images (29)
LCD monitor (Standard Display) See pages in parentheses for details of operation. In AUTO or Scene Selection mode Display Display Shooting images A In P/A/S/M mode Indication Focus mode (79) Indication P A S M Mode dial (48 – 67) AF area (80) Metering mode (91) 1/125 Shutter speed (62) F5.6 Aperture (60) +2.
C Display Indication Remaining battery (18) Image quality (119) Image size (118)/Aspect ratio (118) Memory card (22) 100 74 Remaining number of recordable images (29)
Viewfinder Display Indication AF area (80) Shooting area for aspect ratio 16:9 (118) * When using the HVL-F58AM/HVLF42AM Flash (sold separately), you can shoot with the High-speed sync feature at any shutter speed. For details, refer to the operating instructions supplied with the flash. B Display Indication Flash compensation (90) Flash charging (84) WL Wireless flash (87) High-speed sync* Manual focus (81) z Focus 125 Shutter speed (62) 5.
Using the shooting function Selecting the focus method There are two methods for adjusting the focus: autofocus and manual focus. Depending on the lens, the method for switching between the auto focus and manual focus is different. The switch to be used The lens is Lens (Always set equipped with a the focus mode focus mode switch switch on the camera to AF.) The lens is not Camera equipped with a focus mode switch The type of lens To switch to auto focus Set the focus mode switch on the lens to AF.
3 Press the shutter button halfway Focus area sensor down to check the focus and shoot the image. • When the focus is confirmed, the focus indicator changes to z or (below). • The green frames are indicated at an area where the focus has been confirmed. Focus area Focus indicator Shooting technique • To select the area used for focusing, set up [AF area] (page 80). Focus indicator Status z lit Focus locked. Ready to shoot. lit Focus is confirmed. Focal point moves following a moving subject.
To measure the exact distance to the subject The mark located on the top of the camera shows the location of the image sensor*. When you measure the exact distance between the camera and the subject, refer to the position of the horizontal line. * The image sensor is the part of the camera that acts as the film. Notes • If the subject is closer than the minimum shooting distance of the attached lens, the focus cannot be confirmed. Make sure you put enough distance between the subject and the camera.
Selecting the focus method to suit the movement of the subject (Autofocus mode) Fn button t [Autofocus mode] t Select the desired setting (Single-shot AF) The camera focuses and the focus is locked when you press the shutter button halfway down. (Automatic AF) The [Autofocus mode] is switched between Single-shot AF and Continuous AF according to the movement of the subject.
Selecting the focus area (AF area) Select the desired AF area to suit the shooting conditions or your preference. The green frames are indicated at an area where the focus has been confirmed. • The area used for focusing is illuminated briefly in viewfinder mode. AF area Area Fn button t [AF area] t Select the desired setting (Wide) The camera determines which of the nine AF areas is used in focusing within the AF area.
Adjusting the focus manually (Manual focus) When it is difficult to get the proper focus in autofocus mode, you can adjust the focus manually. 1 Set the focus mode switch on the lens to MF. 2 When the lens is not equipped Using the shooting function with the focus mode switch, set the focus mode switch on the camera to MF. 3 Rotate the focusing ring of the lens to achieve a sharp focus.
Zooming in in one step You can zoom in to the center of an image using the smart teleconverter (Digital zoom) and record the image. 1 Set the LIVE VIEW/OVF switch to “LIVE VIEW.” 2 Press the button. button • Each time you press the button, the zoom scaling changes as follows: Approx. ×1.4 t Approx. ×2 t Off The image size is automatically set to the following regardless of the selected image size. Zoom scaling Image size Approx. ×1.4 M* Approx.
• When the smart teleconverter is available, [Metering mode] is set to segment).
Using the flash In a dark location, using the flash allows you to shoot the subject brightly, and it also helps to prevent camera shake. When shooting into the sun, you can use the flash to shoot a bright image of the backlit subject. When the mode dial is set to AUTO, the flash pops up automatically if it is dark or you are shooting into the light. 1 on the control button t Select the desired setting 2 After the flash has finished charging, shoot the subject. Flashing: The flash is being charged.
(Flash Off) Does not fire even if it is dark. (Autoflash) Fires if it is dark or against light. (Fill-flash) Fires every time you trigger the shutter. (Slow sync.) Fires every time you trigger the shutter. Slow sync shooting allows you to shoot a clear image of both the subject and the background by slowing the shutter speed. (Rear sync.) Fires right before the exposure is completed everytime you trigger the shutter.
The flash range The range of the built-in flash depends on the ISO sensitivity and aperture value. Refer to the following table. Aperture ISO setting F2.8 F4.0 F5.6 AUTO 1.4 – 7.1 m (4.6 – 23 1 – 5 m (3.3 – 16 feet) feet) 1 – 3.6 m (3.3 – 11 feet) 100 1 – 3.6 m (3.3 – 11 feet) 1 – 2.5 m (3.3 – 8.2 feet) 1 – 1.8 m (3.3 – 5.9 feet) 200 1 – 5.1 m (3.3 – 16 feet) 1 – 3.5 m (3.3 – 11 feet) 1 – 2.5 m (3.3 – 8.2 feet) 400 1.4 – 7.1 m (4.6 – 23 1 – 5 m (3.3 – 16 feet) feet) 800 2 – 10 m (6.
Performing wireless flash shooting With an external wireless flash (sold separately), you can shoot with the flash without a cord when the external flash is not attached to the camera. By changing the position of the flash, you can shoot an image with a three dimensional feel by highlighting the contrast of light and shadow on the subject. For the actual steps of shooting, refer to the operating instructions of the flash.
Adjusting the brightness of the image (Exposure, Flash compensation, Metering) Using brightness compensation for the entire image (Exposure compensation) Except for recording mode M, the exposure is automatically selected (Automatic exposure). Based on the exposure acquired by the automatic exposure, you can perform exposure compensation by shifting the exposure to either the + side or the – side, depending on your preference. You can make the entire image brighter by shifting to the + side.
3 Adjust the focus and shoot the subject. Shooting techniques • Adjust the compensation level by checking the recorded image. • Using bracket shooting, you can shoot multiple images with the exposure shifted to the plus or minus sides (page 101). Note • This item cannot be set when the exposure mode is set to AUTO or Scene Selection. To shoot while checking the screen using the histogram Dark Light The exposure compensation will change the histogram accordingly. The right illustration is an example.
Notes • The histogram displayed in Live View mode does not indicate the final recorded image. It indicates the condition of the image just monitored on the LCD monitor. The histogram will differ based on aperture setting, etc. • The histogram differs between shooting and playback in the following situations: – When firing the flash. – When the subject has low intensity, such as night scenery.
Selecting the method for measuring the brightness of a subject (Metering mode) Fn button t [Metering mode] t Select the desired mode (Multi segment) This mode measures light on each area after dividing the total area into multiple areas and determines the proper exposure of the entire screen. (Center weighted) While emphasizing the central area of the screen, this mode measures the average brightness of the entire screen.
Setting ISO Sensitivity to light is expressed by the ISO number (recommended exposure index). The larger the number, the higher the sensitivity. 1 Press ISO on the control button to display the ISO screen. 2 Select the desired value with v/V on the control button. • The larger the number, the higher the noise level. Notes • When the exposure mode is set to AUTO or Scene Selection, ISO is fixed to AUTO and you cannot select other ISO numbers.
Adjusting the color tones (White balance) The color tone of the subject changes depending on the characteristics of the light source. The table below shows how the color tone changes based on various light sources, compared with a subject that appears white under the sunlight.
AWB (Auto WB) The camera automatically detects a light source and adjusts the color tones. (Daylight) If you select an option to suit a specific light source, the color tones are adjusted for the light source (preset white balance). (Shade) (Cloudy) (Tungsten) (Fluorescent) (Flash) Shooting technique • When you select (Custom), you can register your setting (below).
4 Press the center of the control button. The monitor returns to the recording information display with the memorized custom white balance setting retained. • The custom white balance setting registered in this operation is effective until a new setting is registered. Note • The message “Custom WB error” indicates that the value is beyond the expected range. (When the flash is used on a subject in close proximity or a subject with a bright color is in the frame.
Image processing Correcting the brightness of the image (D-Range Optimizer) Fn button t [D-RangeOptimizer] t Select the desired setting (Off) No optimization. (Standard) When there is a sharp contrast of light and shadow between the subject and the background, which is common when shooting into the sun, the camera attenuates the contrast across the entire image to produce an image with proper brightness and contrast.
(Standard) For shooting various scenes with rich gradation and beautiful colors. (Vivid) The saturation and contrast are heightened for shooting striking images of colorful scenes and subjects such as flowers, spring greenery, blue sky, or ocean views. (Portrait) For shooting the skin color in a soft tone, ideally suited to shooting portraits. (Landscape) The saturation, contrast, and sharpness are heightened for shooting vivid and crisp scenery. Distant landscapes also stand out more.
Changing the range of color reproduction (Color Space) The way colors are represented with combinations of numbers or the range of color reproduction is called “color space.” You can change the color space, depending on your purpose. MENU button t setting 2 t [Color Space] t Select the desired sRGB This is the standard color space of the digital camera. Use sRGB in normal shooting, such as when you intend to print out the images without any modification.
Selecting the drive mode This camera has five drive modes, such as single-shot advanced, and continuous advanced. Use them to suit your purpose. Shooting single shot This mode is for normal shooting. on the control button t (Single-shot adv.) (Sports Action) in Scene Selection, you cannot Shooting continuously The camera records the images continuously at the following speeds*. Live View mode Maximum 2 images per second Viewfinder mode Maximum 2.5 images per second * Our measurement conditions.
2 Adjust the focus and shoot the subject. • When you press and hold the shutter button, the recording continues. The maximum number of continuous shots The number of continuous shooting images obtainable has an upper limit. Fine/Standard No limit (Until the memory card is full) RAW & JPEG 3 images RAW 6 images Notes • You cannot shoot images continuously when “0” flashes in the viewfinder. Wait until the indicator disappears.
2 Adjust the focus and shoot the subject. • When the self-timer is activated, audio signals and the self-timer lamp indicate the condition. The self-timer lamp flashes quickly and the audio signal sounds quickly right before the shooting. To cancel the self-timer Press on the control button. Note • When you shoot images using the viewfinder, use the eyepiece cover (page 28). Shooting images with the exposure shifted (Exposure bracket) – direction + direction 1 on the control button t (Bracket: Cont.
* (Bracket: Cont.) Shoots three images with the exposure shifted by a selected step. Press and hold the shutter button until the recording stops. When the flash is fired, press the shutter button shot by shot. * _ EV displayed with is the step currently selected. Notes • When the mode dial is set to M, the exposure is shifted by adjusting the shutter speed. • When you adjust the exposure, the exposure is shifted based on the compensated value.
• In viewfinder mode, if the shutter button is pressed halfway down and released, “br 1” appears. “Fbr 1” appears for the flash bracket. When flash bracket shooting starts, it indicates what number the next frame is, for instance, “Fbr 2,” “Fbr 3.” Shooting with the Remote Commander You can shoot using the SHUTTER and 2SEC (the shutter is released after 2 seconds) buttons on the RMT-DSLR1 Wireless Remote Commander (sold separately).
Using the viewing function Playing back images The last recorded image is displayed on the LCD monitor. 1 Press the button. button 2 Select an image with b/B on the control button. To return to the shooting mode Press the button again. To switch the recording data display Press DISP on the control button. Each time you press DISP on the control button, the screen changes as follows.
Rotating an image 1 Fn button t [Rotate] 2 Press the center of the control button. The image is rotated counter-clockwise. When you want to do another rotation, repeat step 2. • Once you rotate the image, the image is played back in the rotated position, even if you turn off the power. To return to the normal playback screen Press the button. Enlarging images An image can be enlarged for closer examination. This is convenient to check the focus condition of a recorded image.
3 Select the portion you want to enlarge with v/V/b/B on the control button. To cancel the enlarged playback Press the button so that the image returns to the normal size. Scaling range The scaling range is as follows. Image size Scaling range DSLR-A380 DSLR-A330 L Approx. ×1.1 – ×14 Approx. ×1.1 – ×12 M Approx. ×1.1 – ×11 Approx. ×1.1 – ×9.1 S Approx. ×1.1 – ×7.2 Approx. ×1.1 – ×6.
Playing back images automatically (Slide show) The slide show can be operated either using the Fn button or the MENU button. Here operation using the Fn button is described. Fn button t [Slide show]t [OK] Plays back recorded images in order (Slide show). The slide show automatically stops after all the images have been played back. • You can view the previous/next image with b/B on the control button. To pause the slide show Press the center of the control button.
Checking the information of recorded images Each time you press DISP on the control button, the information display changes (page 104). Basic information display Display Indication Display Indication Memory card (22) NO CARD “No card” warning 100-0003 Folder - file number (137) - Protect (111) DPOF3 DPOF set (145) Image quality (119) Image size (118)/Aspect ratio (118) Remaining battery warning (18) 1/125 Shutter speed (62) F3.
Histogram display A Display Display –0.
About the flashing segments on the histogram display When the image has a high-key or lowkey portion, that portion is flashed on the histogram display (Luminance limit warning).
Protecting images (Protect) You can protect images against accidental erasure. The protect function can be operated either using the Fn button or the MENU button. Here operation using the Fn button is described. Protecting selected images/canceling the protection of the selected images 1 Fn button t [Protect] t [Marked images] 2 Select the image you want to protect with b/B on the control button, then press the center of the control button.
Deleting images (Delete) Once you have deleted an image, you cannot restore it. Check whether to delete the image or not beforehand. The delete function can be operated either from the Fn button or from the MENU button. Here operation using the Fn button is described. Note • Protected images cannot be deleted. Deleting the image that is currently displayed 1 Display the image you want to delete and press the button. button 2 Select [Delete] with v, then press the center of the control button.
4 Press the Fn button. 5 Select [Delete] with v on the control button, then press the center of the control button. Deleting all the images in the folder 1 Fn button t [Image Index] t Select the desired number of images 2 Select the folder bar with b on the control button. 3 Press the center of the control button, then select the folder you want to delete with v/V. 4 Press the button. 5 Select [Delete] with v, then press the center of the control button.
Viewing images on a TV screen To view images recorded on the camera on a TV set, an HDMI cable (sold separately) and an HD TV equipped with an HDMI connector are required. 1 Turn off both your camera and the TV, and connect the camera to the TV. 1 To the HDMI connector HDMI cable (sold separately) 2 To the HDMI terminal 2 Turn on the TV and switch the input. • See also the operating instructions supplied with the TV. 3 Turn on the camera. Images shot with the camera appear on the TV screen.
• By connecting your camera to Sony’s VIDEO-A compatible TV using an HDMI cable, the TV automatically selects the appropriate image quality for viewing still pictures. Please refer to the operating instructions of Sony’s VIDEO-A compatible TV for more details. • Some devices may not work properly. • Do not connect the output connector of the device with the HDMI terminal on the camera. This may cause a malfunction. On “PhotoTV HD” This camera is compatible with the “PhotoTV HD” standard.
PAL-N system Argentina, Paraguay, Uruguay SECAM system Bulgaria, France, Guiana, Iran, Iraq, Monaco, Russia, Ukraine, etc. Using “BRAVIA” Sync By connecting the camera to a TV that supports “BRAVIA” Sync using an HDMI cable, you can operate the camera with the TV Remote Control. 1 Connect a TV that supports “BRAVIA” Sync to the camera (page 114). The input is automatically switched and the image shot with the camera appears on the TV screen. 2 Press the LINK MENU button on the TV Remote Control.
• If the camera performs unnecessary operations in response to the TV Remote Control when the camera is connected to another manufacturer’s TV using an HDMI connection, set [CTRL FOR HDMI] in the Setup menu to [Off].
Changing your setup Setting image size and image quality Image size MENU button t 1 t [Image size] t Select the desired size [Aspect ratio]: [3:2] DSLR-A380 L:14M 4592 × 3056 pixels M:7.7M 3408 × 2272 pixels S:3.5M 2288 × 1520 pixels DSLR-A330 L:10M 3872 × 2592 pixels M:5.6M 2896 × 1936 pixels S:2.5M 1920 × 1280 pixels [Aspect ratio]: [16:9] DSLR-A380 L:12M 4592 × 2576 pixels M:6.5M 3408 × 1920 pixels S:2.9M 2288 × 1280 pixels DSLR-A330 L:8.4M 3872 × 2176 pixels M:4.
3:2 A normal ratio. 16:9 An HDTV ratio. Quality MENU button t (RAW) (RAW & JPEG) (Fine) (Standard) 1 t [Quality] t Select the desired setting File format: RAW (raw data) This format does not perform any digital processing on the images. Select this format to process images on a computer for professional purposes. • The image size is fixed to the maximum size. The image size is not displayed on the LCD monitor.
Setting the method for recording on a memory card Selecting the method for assigning file numbers to images MENU button t setting 2 t [File number] t Select the desired Series The camera does not reset numbers and assigns numbers to files in sequence until the number reaches “9999.” Reset The camera resets numbers in the following cases and assigns numbers to files from “0001.” When the recording folder contains a file, a number one higher than the largest number is assigned.
Creating a new folder You can create a folder in a memory card for recording images. A new folder is created with a number incremented one higher than the largest number currently used, and the folder becomes the current recording folder. MENU button t 2 t [New folder] Selecting the recording folder When a standard form folder is selected and there are two or more folders, you can select the recording folder to be used to record images.
Changing the noise reduction setting Disabling the noise reduction during long exposure shootings When you set the shutter speed to a second or longer (Long exposure shooting), noise reduction is turned on for the same duration that the shutter is open. This is to reduce the grainy noise typical in a long exposure. When noise reduction is in progress, a message appears and you cannot take another picture. Select [On] to prioritize the image quality. Select [Off] to prioritize the timing of shooting.
Changing the functions of the control dial Changing the function of the control dial When the recording mode is M (Manual exposure), you can set the camera so that the adjustable item (the shutter speed or the aperture value) can be selected using only the control dial. It is convenient if you select the most commonly-used item when adjusting the exposure.
Changing other settings Setting the sound on/off Selects the sound produced when the shutter is locked, during self-timer countdown, etc. MENU button t setting 3 t [Audio signals] t Select the desired Selecting the background color of the screen display You can select the background color of the LCD monitor from [Black], [White], [Brown], or [Pink].
Note • Regardless of the setting here, the camera turns to power save mode after 30 minutes when the camera is connected to a TV or the drive mode is set to (Remote Commander). Setting the date Resets the date. See page 25 for details.
Setting the LCD monitor Setting the brightness of the LCD monitor manually The brightness of the LCD monitor is automatically adjusted to the surrounding lighting conditions using the light sensor (page 36). You can set the brightness of the LCD monitor manually. MENU button t 1 t [LCD brightness] t [Manual] t Select the desired setting Notes • When it is set to [Auto], do not cover the light sensor with your hand and so on.
Keeping the LCD monitor tuned on while looking into the viewfinder When the LIVE VIEW/OVF switch is set to “OVF,” looking into the viewfinder turns off the LCD monitor. In the default setting, while looking into the viewfinder, the LCD monitor is turned off to prevent the battery pack from wearing down. If you want to turn on the LCD monitor while looking into the viewfinder, select [Off].
Confirming the version of the camera Displaying the version Displays the version of your camera. Confirm the version when a firmware update is released. MENU button t 3 t [Version] Note • An update can be performed only when the battery level is (three remaining battery icons) or more. We recommend that you use a sufficient battery or the ACPW10AM AC Adaptor (sold separately).
Resetting to the default You can reset the main functions of the camera. MENU button t 3 t [Reset default] t [OK] The items to be reset are as follows. Items Reset to Exposure compensation (88) ±0.0 Recording information display (70) Graphic Display Playback display (104) Single-image screen (with recording information) Drive mode (99) Single-shot adv.
Custom menu Items Reset to Eye-Start AF (68) On Ctrl dial setup (123) Shutter speed Red eye reduc.
Viewing images on a computer Copying images to your computer This section describes how to copy images in a memory card to a computer connected using a USB cable. Recommended computer environment The following environment is recommended for a computer connected to the camera to import images.
Stage 1: Connecting the camera and your computer 1 Insert a memory card with recorded images into the camera. 2 Select the type of memory card you want to copy images from using the memory card switch. 3 Insert the sufficiently charged battery pack in the camera, or connect the camera to a wall outlet (wall socket) with the AC Adaptor (sold separately).
Stage 2: Copying images to a computer For Windows This section describes an example of copying images to a “Documents” (For Windows XP: “My Documents”) folder. When you use the supplied “PMB” software, you can copy images easily (page 139). 1 Click [Open folder to view files] (For Windows XP: [Open folder to view files] t [OK]) as the wizard screen appears automatically on the desktop. • When the wizard screen does not appear, click [Computer] (For Windows XP: [My Computer]) t [Removable Disk].
4 Double-click the [Documents] folder. Then, right-click on the “Documents” window to display the menu and click [Paste]. The image files are copied to the “Documents” folder. • When an image with the same file name exists in the copy destination folder, the overwrite confirmation message appears. When you overwrite an existing image with a new one, the original file data is deleted.
Viewing images on your computer For Windows This section describes the procedure for viewing copied images in the “Documents” (For Windows XP: “My Documents”) folder. To view RAW images, the supplied “Image Data Converter SR” software is required (page 142). 1 Click [Start] t [Documents]. • If you are using Windows 2000, double-click [My Documents] on the desktop. 2 Double-click the desired image file. The image is displayed.
x For Windows Double-click on the tasktray, then click (USB Mass Storage Device) t [Stop]. Confirm the device on the confirmation window, then click [OK]. The device is disconnected. x For Macintosh Drag and drop the drive icon or the icon of the memory card to the “Trash” icon. The camera is disconnected from the computer.
Image file storage destinations and file names The image files recorded with your camera are grouped as folders on the memory card. Example: viewing folders on Windows Vista Copying images stored on a computer to a memory card and viewing the images This section describes the process using a Windows computer as an example. Step 1 is not necessary if the file name has not been changed. When you use the supplied “PMB” software, you can copy images easily (page 139).
1 Right-click the image file, then click [Rename]. Change the file name to “DSC0ssss.” • Enter a number from 0001 to 9999 for ssss. • If the overwrite confirmation message appears, enter a different number. • An extension may be displayed depending on the computer settings. The extension for images is JPG. Do not change the extension. 2 Copy the image file to the memory card folder in the following order. 1 Right-click the image file, then click [Copy].
Using the software To utilize images recorded with the camera, the following software is provided: • Sony Image Data Suite “Image Data Converter SR” “Image Data Lightbox SR” • Sony Picture Utility “PMB” (Picture Motion Browser) Note • “PMB” is not compatible with Macintosh computers. Recommended computer environment x Windows Recommended environment for using “Image Data Converter SR Ver.
x Macintosh Recommended environment for using “Image Data Converter SR Ver.3”/ “Image Data Lightbox SR” OS (pre-installed): Mac OS X (v10.4/v10.5) CPU: Power PC G4/G5 series (1.0 GHz or faster is recommended)/Intel Core Solo/Core Duo/Core 2 Duo or faster Memory: 1 GB or more is recommended. Display: 1024 × 768 dots or more Installing the software x Windows • Log on as Administrator. 1 Turn on your computer, and insert the CD-ROM (supplied) into the CD-ROM drive. The installation menu screen appears.
3 Remove the CD-ROM after the installation is complete. The following software is installed and shortcut icons appear on the desktop. • Sony Image Data Suite “Image Data Converter SR” “Image Data Lightbox SR” • Sony Picture Utility “PMB” “PMB Guide” x Macintosh • Log on as Administrator. 1 Turn on your Macintosh computer, and insert the CD-ROM (supplied) into the CD-ROM drive. 2 Double-click the CD-ROM icon. 3 Copy the [IDS_INST.pkg] file in the [MAC] folder to the hard disk icon.
Using “Image Data Converter SR” Note • If you save an image as RAW data, the image is saved in the ARW2.1 format. With “Image Data Converter SR” you can: • Edit images recorded in RAW format with various corrections, such as tone curve, and sharpness. • Adjust images with white balance, exposure, and creative style, etc. • Save the images displayed and edited on a computer. You can either save the image as RAW format or save it in the general file format.
To start Help from the Start menu, click [Start] t [All Programs] t [Sony Image Data Suite] t [Help] t [Image Data Lightbox SR]. To start up/exit “Image Data Lightbox SR” x Windows Double-click [Image Data Lightbox SR] on the desktop. When starting up from the Start menu, click [Start] t [All Programs] t [Sony Image Data Suite] t [Image Data Lightbox SR]. To exit, click the button on the upper-right corner of the screen. The dialogue used for saving a collection appears.
To start up/exit “PMB” Double-click the (PMB) icon on the desktop. Or, from the Start menu: Click [Start] t [All Programs] t [Sony Picture Utility] t [PMB]. To exit the “PMB,” click button on the upper-right corner of the screen. Note • The confirmation message of the Information tool appears on the screen when starting “PMB” for the first time. Select [Start]. This function informs you of news, such as software updates. You can change the setting later.
Printing images Specifying DPOF Using the camera, you can specify the images and the number of images to print before you print images at a shop or with your printer. Follow the procedure below. DPOF specifications are left with images after printing. It is recommended that you unspecify them after printing. Specifying /unspecifying DPOF on selected images DPOF specifications can be operated either using the Fn button or the MENU button. Here operation using the Fn button is described.
• You can select a value for the number of images to be printed after you have selected [All images]. The same value will be used for all images. Dating images You can date images when printing them. The position of the date (inside or outside the image, character size, etc.) depends on your printer. Fn button t [Specify Printing] t [Date imprint] t [On] Note • This function may not be provided, depending on the printer.
Printing images by connecting the camera to a PictBridge compliant printer Even if you do not have a computer, you can print images shot using your camera by connecting the camera directly to a PictBridge compliant printer. “PictBridge” is based on the CIPA standard. (CIPA: Camera & Imaging Products Association) Note • You cannot print RAW images. Stage 1: Setting the camera Note • It is recommended to use the AC Adaptor (sold separately) to prevent the power from turning off partway through printing.
Stage 2: Connecting the camera to the printer 1 Connect the camera to the printer. 1 To the USB terminal USB cable 2 To the USB terminal 2 Turn on your camera and the printer. The screen used for selecting images you want to print appears. Stage 3: Printing 1 Select the image to print with b/B on the control button, then press the center of the control button. • To cancel, press the center again. 2 Repeat step 1 if you want to print other images. 3 Press the MENU button and set up each item.
To cancel the print During printing, pressing the center of the control button cancels the print. Remove the USB cable or turn off the camera. When you want to print again, follow the procedure (Stages 1 to 3) above. PictBridge menu Print Prints the selected images. For details, see “Stage 3: Printing.” Set print q’ty You can specify the number of prints, up to 20. The same number of prints is specified on all the selected images. Paper size Auto Printer setup 9×13cm/3.
Others Specifications [Anti-Dust] System Camera Charge protection coating on Low-Pass Filter and image sensor-shift mechanism [System] [Auto Focus System] Camera Type Digital Single Lens Reflex Camera with built-in flash and interchangeable lenses System Lens All of α Lenses [Image sensor] Total pixel number of camera DSLR-A380 Approx. 14 900 000 pixels DSLR-A330 Approx.
Eye Relief Approximately 19.7 mm from the eyepiece, 14.1 mm from the eyepiece frame at –1 diopter (–1 m–1) Dioptor Adjustment –3.0 to +1.0 m–1 [Exposure control] Metering Cell SPC Metering method 40-segment honeycombpattern, the exclusive image sensor for Live View in Live View mode Metering Range 2 to 20 EV (4 to 20 EV with Spot metering), (at ISO 100 with F1.4 lens) 2 to 17 EV in Live View mode (on all metering modes, at ISO 100 with F1.
File format JPEG (DCF Ver. 2.0, Exif Ver. 2.21, MPF Baseline) compliant, DPOF compatible Capacity USB communication Hi-Speed USB (USB 2.0 compliant) Maximum dimensions Approx. 31.8 × 18.5 × 45.0 mm (1 5/16 × 3/4 × 1 13/16 inches) (W/H/D) BC-VH1 Battery charger Mass Input rating 100 V – 240 V AC, 50/60 Hz, 4 W Design and specifications are subject to change without notice. Typical 6.1 Wh (900 mAh) Minimum 5.9 Wh (870 mAh) Approx. 50 g (1.8 oz) Output rating 8.4 V DC, 0.
• Adobe is a registered trademark or a trademark of Adobe Systems Incorporated in the United States and/or other countries. • D-Range Optimizer Advanced uses technology provided by Apical Limited. • In addition, system and product names used in this manual are, in general, trademarks or registered trademarks of their respective developers or manufacturers. However, the ™ or ® marks are not used in all cases in this manual. Others Trademarks • is a trademark of Sony Corporation.
Troubleshooting If you experience trouble with your camera, try the following solutions. Check the items on pages 154 to 163. Consult your Sony dealer or local authorized Sony service facility. 1 Check the following items. 2 Remove the battery pack, and insert the battery pack again after about one minute, and turn on the power. 3 Reset the settings (page 129). 4 Consult your Sony dealer or local authorized Sony service facility. Battery pack and power The battery pack cannot be installed.
The power turns off suddenly. • If you do not operate the camera for given period of time, the camera turns to power saving mode and nearly shuts down. To cancel the power save, operate the camera, such as pressing the shutter button halfway down (page 124). The CHARGE lamp flashes when charging the battery pack. • Remove and re-insert the battery pack correctly. • Charge the battery pack under the suitable temperatures between 10 and 30°C (50 and 86°F).
• • • • You cannot record images while charging the built-in flash (page 84). The shutter cannot be released when the subject is out of focus. The lens is not attached properly. Attach the lens properly (page 20). When an astronomical telescope, etc., is attached to the camera, set the recording mode to M and do your shooting. • The subject may require special focusing (page 77). Use the focus-lock or manual focus function (pages 78, 81). Recording takes a long time.
A picture taken with the flash is too dark. • If the subject is beyond the flash range (the distance that the flash can reach), the pictures will be dark because the flash light does not reach the subject. If the ISO is changed, the flash range also changes with it (page 86). • In the following cases, the image may be dark. Remove these accessories, then shoot. – An ND filter or a PL filter. – A diffuser. – A wide panel for the HVL-F36AM flash. The date and time are recorded incorrectly.
Dots appear and remain on the LCD monitor. • This is not a malfunction. These dots are not recorded (page 7). • You may reduce the effect of these issues using the “Pixel mapping” function. 1 Set the LIVE VIEW/OVF switch to “LIVE VIEW.” 2 Attach the lens cap. 3 MENU button t 3 t [Pixel mapping] t [OK] The image is blurred. • The picture was taken in a dark location without the flash, resulting in camera shake. The use of a tripod or the flash is recommended (pages 47, 84).
You have deleted an image by mistake. • Once you have deleted an image, you cannot restore it. We recommend that you protect images that you do not want to delete (page 111). You cannot mark a DPOF mark. • You cannot mark DPOF marks on RAW images. Computers You do not know if the OS of your computer is compatible with the camera. • Check “Recommended computer environment” (pages 131, 139). Your computer does not recognize your camera. • Check that the camera is turned on.
After making a USB connection, “PMB” does not start automatically. • Make the USB connection after the computer is turned on (page 132). You do not know how to operate the software (supplied). • See help or the guide of each software. Memory card Cannot insert a memory card. • Insertion direction of the memory card is wrong. Insert it in the correct direction (page 22). Cannot record on a memory card. • The memory card is full. Delete unnecessary images (page 112).
Images are printed with both edges cut off. • Depending on your printer, the left, right, top, and bottom edges of the image may be cut off. Especially when you print an image shot with the aspect ratio set to [16:9], the lateral end of the image may be cut off. • When printing images using your own printer, cancel the trimming or borderless settings. Consult the printer manufacturer as to whether the printer provides these functions or not.
Cannot print images. • Check that the camera and the printer are properly connected using the USB cable. • RAW images cannot be printed. • Images shot using cameras other than this camera or images modified with a computer may not be printed. “---- -- --” is printed on the date-inserted part of the image. • Images that do not have the recording data/time information cannot be printed with the date inserted. Set [Date imprint] to [Off] and print the image again (page 149).
The setting is reset without the resetting operation. • The battery pack was removed when the power switch was set to ON. When removing the battery pack, make sure the camera is turned off and the access lamp is not illuminated (pages 17, 37). The camera does not work properly. • Turn off the camera. Remove the battery pack and insert it again. If an AC Adaptor (sold separately) is used, disconnect the power cord. If the camera is hot, allow it to cool down before trying this corrective procedure.
Warning messages If the following messages appear, follow the instructions below. Incompatible battery. Use correct model. • An incompatible battery pack is being used (page 18). Set date and time? • Set the date and time. If you have not used the camera for a long time, charge the internal rechargeable battery (pages 25, 167). Power insufficient • You tried to perform [Cleaning mode] when the battery level is insufficient. Charge the battery pack or use the AC Adaptor (sold separately).
Unable to display. • Images recorded with other cameras or images modified with a computer may not be able to be displayed. No lens attached. Shutter is locked. • The lens is not attached properly, or the lens is not attached. • When attaching the camera to an astronomical telescope or something similar, set the recording mode to M. No images • There is no image in the memory card. Image protected • You tried to delete protected images. Camera overheating. Allow it to cool.
Unable to mark. • You attempted to mark RAW images on the PictBridge screen. Printer error • Check the printer. • Check if the image you want to print is corrupted. Printer busy • Check the printer.
Precautions On operating temperatures Do not use/store the camera in the following places Your camera is designed for use under the temperatures between 0 and 40°C (32 and 104°F). Shooting in extremely cold or hot places that exceed this range is not recommended. • In an extremely hot, dry or humid place In places such as in a car parked in the sun, the camera body may become deformed and this may cause a malfunction.
This rechargeable battery is continually charged as long as you are using the camera. However, if you use the camera for only short periods, it discharges gradually, and if you do not use the camera at all for about 3 months it becomes completely discharged. In this case, be sure to charge this rechargeable battery before using the camera. However, even if this rechargeable battery is not charged, you can still use the camera as long as you do not record the date and time.
Index Index Numerics 40-segment honeycomb pattern metering ............................... 151 A Adobe RGB................................ 98 AF area....................................... 80 AF illuminator............................ 86 Ambient light ........................... 102 Amount of exposure................... 57 Anti-dust function ...................... 33 Aperture ............................... 57, 60 Aperture priority ........................ 60 Aspect ratio ..............................
ISO sensitivity ........................... 92 Eyecup ........................................28 Eyepiece cover............................28 Eyepiece sensors.................68, 127 Eye-Start AF ...............................68 J F L File number...............................120 Fill-flash .....................................84 Flash bracket.............................101 Flash compensation ....................90 Flash mode..................................84 Flash Off .............................
O OVF ........................................... 68 P PictBridge ................................ 147 Pixel mapping .......................... 158 PlaybackDisplay ...................... 104 PMB ......................................... 143 Portrait ....................................... 51 Power Save .............................. 124 Preset white balance................... 93 Pressing halfway down .............. 49 Print.................................. 145, 147 Program auto............................